similar to: SUSE 10.0 and MGE Ellipse

Hi, I have installed in suse 9.3 and ellipse premium 500 usb a psp 3.0 with yast2 and versions: nut-2.0.2-4 mgeups-psp-3.0.0-3 the first time that I launch psp it seems to contact the UPS and you can make changes to the parameters and all seems ok. If you make a reboot the psp hangs up and if you try /etc/init.d/ups it fails: Starting service NUT: -> Starting UPS driver: Network UPS Tools -

2006/1/13, Paul Mogren <fkamogee@yahoo.com>: > > This thread is FYI. I don't need any help here. > no, but some details for those who will read it, maybe ;-) I have SUSE 10.0 and an MGE Ellipse. I installed the NUT package from MGE. > > 1) The generated ups.conf pointed to a bad location: > /dev//dev/input/event0 > who generated that ? it seems like an old hiddev

I have an Ellipse USBS connected via serial cable to a CentOS 3 box. Do I need to turn off the UPS as the final stage of shutdown, or will the UPS power itself off, before the battery reaches a level to low to safely recharge from? I notice there is the option for the UPS to turn itself off (and on again) unattended if power is restored during shutdown, but there doesn't seem to be an option

Hi, I bought an Ellipse MAX 1100 a few months ago. First I attached it to my desktop and installed mge's personal solution pac. (a graphical interface which uses nut). It works. But I want to attach the ups to my server which runs without an x-server. I followed http://opensource.mgeups.com/install/debian.htm. Didn't work. Then I copied over the configuration files which the personal

Dear List, The driver usbhid-ups does not detect my MGE Ellipse 1500. I'm running openSuSE Linux 10.3, kernel 2.6.22 with mgeups-psp-3.0.4-2, nut-2.2.0-20 installed from MGE's rpm's. (Merci MGE!) lsusb shows: Bus 001 Device 004: ID 0463:ffff MGE UPS Systems UPS /etc/ups/ups.conf says: [myups] driver = usbhid-ups port = auto desc = "Local UPS"

Hi Arnaud, hi all I wish you all the best for 2006. Enjoying of some less stressed time, I follow your advice, Arnaud, to switch our UPS management on the newhidups driver. ( Enfin ! ;) Our goal is to support (soon) the new MGE ASR ELLIPSE ( and of course also the old ELLIPSE and EXTREME models ). I rebuild the libusb-0.1.10a packages to conform to our installation process. I perform the same

Hello, I'm using NUT with an MGE Ellipse USB, which I understand to be rather slow to respond. Every time I start the NUT services, I get the "Communications lost" notifications at first, but then it starts to work normally. I've increased polling frequencies in upsmon.conf to the point that I get only one "Communications lost" before it starts to work, but I can't

Hi I try since a week to run my MGE Protection Center under Suse Linux 9.3. At the MGE site i found an HowTo. I have installed NUT an create the=20 configs but at boot the newhidups driver say=B4s "no USB/HID UPS found".=20= Anyone an Idea? Johannes Schatz=

Fellows, back for 4 days, the baby and the mother are now at home, and the father is... hem, well not so fresh ;-) For those interested in some pictures: http://benjamin.quette.free.fr/ 2006/11/16, Peter Selinger <selinger@mathstat.dal.ca>: > ... > Arnaud: could you please amend the instructions on the NUT download > website http://www.networkupstools.org/source.html (Development

Dear List, I thought it might be useful if I wrote up my notes on getting an MGE UPS to work with NUT and openSUSE. The MGE UPS (an Ellipse 1500 USB) will work well with NUT and openSUSE 10.2, but not "out-of-the-box": there are some things you need to do: Intro. MGE have built rpms of NUT which greatly simplify installation. Merci MGE. I used the rpm's for nut-2.0.5 and the

I'm now doubting if I've made this statement or not, so here it is: newmge-shut is *not* ready for production usage! I've lately found some bugs during the MGE PSP 3.0.4/3.0.5/3.0.6 updates. So for the moment, prefer to keep using mge-shut. 2007/10/25, R?zsa G?bor <mailer.tovis at freemail.hu>: > newmge-shut ??? > Shutdown, switch of ups does not work. Using command >

- UPS MGE Premium Ellipse Premium 1200 - SuSE Linux 10.0 OSS, kernel 2.6.13 smp - gcc version 4.0.2 20050901 (prerelease), glibc-2.3.5-40 - mgeups-psp-3.0.0-3, nut-2.0.2-4 - Dell Dimension 8400 with dual core Intel Xeon. 3.0GHz. lsusb shows: Bus 002 Device 003: ID 0463:ffff MGE UPS Systems UPS less /proc/bus/usb/devices shows for bus 2 device 3: T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=

Hi, I'm forwarding your mail to the NUT list, because of a lack of time, and also since some others (Charles) already looked at this issue IIRC (related to the development branch 'netport'). cheers, Arnaud -- Linux / Unix Expert R&D - Eaton - http://powerquality.eaton.com Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

[fwded to the list] Hi Fran?ois, > I didn't post this on the list as it seems a little bit more MGE > stuff than nut. Anyway feel free to post it if you consider it's > relevant. > > This is the trace you were asking for. The Ellipse 800 correctly shut > down in this test : > > This was running on a i386 recent hardware, the cpu load is under 5%, > 360MB out of

Hello, I have Ellipse ASR 1500 UPS and now I'm trying to monutor it with NUT from FreeBSD. It seems that there are some problems with this UPS: =================================== ugen0: MGE UPS SYSTEMS ELLIPSE, rev 1.10/42.41, addr 2 > usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), NEC(0x0000), rev 1.00 port 1 powered port 2

I've recently bought an MGE 650 that has both cables : USB and Serial. Since it's used on a server, I'd prefer not to load usb drivers just for nut. The problem is, either with newhidups or with mge-shut, the driver instantanly report that the communication with my MGE is lost, and shotly after that my ups is unavailable. It never show up again, and nut constantly says that the

Hello, It is 3 or 4 weeks ago since, i want to set communication with my ups a MGE NOVA 1100 AVR. I do it first with manual configuration but after no success, i prefered to install mgeups-psp package to do it directly. But since when i execute psp, the attempt finish with an "No communication with UPS" error. Same is when i type: mge-shut -u root -DDDDDDDDDD /dev/ttyS0 . I unplog

I have an MGE Ellipse Premium 1200 that I connected to my server using its USB cable. Nut seems to be working fine. I've done a power down test and it worked and came back up when the UPS had power again. I'm using the newhidups driver and the USB cable. The problem I'm having is that if I boot with the cable connected newhidups says it can't find the UPS. If I unplug and plug in

My new MGE Ellipse Premium 1200 is now working fine. I've tested pulling the plug and the computer shuts down properly and comes back up when I replug. The only strange behaviour is that when I put the power back on the battery shows as being at 86%. If it was at 86% it should have lasted longer. Is there any calibration step I can do? The only commands the ups seems to support are: $ upscmd

Hello everybody, Our supoprt team is facing a problem which froze the CPU. They suspect that this happens after an automatic battery test, which lets the battery goes down to 30% and then stop the test. At this level of charge, our kernel also triggers a shutdown (CPU and UPS). I saw (in the doc found here : tools.*mge*ops.net/download/intl/products/*ellipse*-asr/28-umeasr_08.pdf) that this