similar to: Re: Mac Clients for nut

Hi Roger, Thanks very much for your answer. I appreciate! > The silence says that there is currently very little interest in NUT on > Windows, and to the best of my knowledge no-one is working on it. I would not argue the fact that there's obviously less interest in NUT on Windows than on Linux. But still, some few comments: 1/ There's maybe LESS interest, but there's some

Hello, I'm using NUT to manage a MGE Ellipse ASR UPS, with the newhidups driver. It works fine, except that after a few hours, I get a few errors from the kernel and the driver dies. Here's the output from the syslog: Apr 26 02:00:41 ezquiel kernel: usb 1-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110 Apr 26 02:00:43 ezquiel last message repeated 2 times

I changed IP to NAS IP instead of my PC IP and also used NAS login and pass. Didn't work. When I wanted to launch WinNUT with new settings I got: "Fatal error: insufficient power configured!" (same as before) I got this log: Level INFO 10/26/2016 10:46:17 Detected OS as Windows NT Level NOTICE 10/26/2016 10:46:17 Network UPS Tools upsmon 2.0.0.4 Level INFO

Hi, Two weeks and no answer. Any direction how to setup a NUT client on Windows? Any kind of documentation anywhere, even a single page? And if I'm not at the right place, where can I find any help? Any one I should get in touch with? There's at least a developer who did this full port to Window? Thanks for your help! Emmanuel Le mar. 29 oct. 2019 à 00:30, <planet.et at

Hi, I bought an Ellipse MAX 1100 a few months ago. First I attached it to my desktop and installed mge's personal solution pac. (a graphical interface which uses nut). It works. But I want to attach the ups to my server which runs without an x-server. I followed http://opensource.mgeups.com/install/debian.htm. Didn't work. Then I copied over the configuration files which the personal

Hi, Another beginner question. I spend hours trying to find the solution for how to configure winnut properly but I' struggling to make it work. I want my QNAP NAS TS-231 to work as a master and send signal to the PC to shut it down during power outage. I configured QNAP properly (like this: http://geekbeat.tv/qnap-adding-external-devices-qnap), but I don't know what to do next. I work

How do you setup the debug options in WinNUT? Correct, it sets the POWERDOWNFLAG when it receives an FSD but only if it acts as a NUT MASTER (since the UPS is connected locally to the NUT MASTER and can issue a killpower). This is the default value and I did not care to change it because it won't be use on my Windows machine anyway as it is working as a NUT SLAVE. Thank you. Regards, Kevin

Dear List, I thought it might be useful if I wrote up my notes on getting an MGE UPS to work with NUT and openSUSE. The MGE UPS (an Ellipse 1500 USB) will work well with NUT and openSUSE 10.2, but not "out-of-the-box": there are some things you need to do: Intro. MGE have built rpms of NUT which greatly simplify installation. Merci MGE. I used the rpm's for nut-2.0.5 and the

Hi, I have an Eaton 5SC UPS with only 1 USB communication port, but... I need 3 devices to safely switch off in case of power failure, 2 Synology NAS and 1 PC under Windows 7 (soon 10)! So I've decided to connect the UPS to the main NAS (via the USB cable), enabled the "Network UPS server" on the NAS, entered the other NAS and PC IP addresses to let them receive NUT messages in case

- UPS MGE Premium Ellipse Premium 1200 - SuSE Linux 10.0 OSS, kernel 2.6.13 smp - gcc version 4.0.2 20050901 (prerelease), glibc-2.3.5-40 - mgeups-psp-3.0.0-3, nut-2.0.2-4 - Dell Dimension 8400 with dual core Intel Xeon. 3.0GHz. lsusb shows: Bus 002 Device 003: ID 0463:ffff MGE UPS Systems UPS less /proc/bus/usb/devices shows for bus 2 device 3: T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=

Hi All! This time I'm using Nut 2.2.0, Debian etch and kernel v. 2.6.23.9. My hardware config is quite simple. There are 2 PCs connected to my PowerMust 600VA. One is mensioned above the other is a Windows PC using Winnut 2.0.0b. The Linux PC is connected to the UPS via a serial cable and acts as the server. The problem is that both upsmon and winnut disconnect regularly but in random

Thank You very much !!! Now I see how was entered the master password in the file : "-v "concat(' password = ',//system/password)" -n \" I will test the proposed solution. Two questions - Do I need separate users for each WinNUT client or they can use the same user for monitoring&shutdown client machines ? - This is maybe a newbie question,

Any comments here? Thank you. Regards, Kevin Mychal M. Ong Sr Infrastructure Engineer, Microsoft Technology Services - Messaging Global Infrastructure Operations Ingram Micro Inc. 4F Three World Square, 22 Upper McKinley Hill, Fort Bonifacio Taguig City, Philippines 1634 Direct +1-716-633-3600 ext. 33996 Mobile +63-917-511-0251 *: kevin.ong at ingrammicro.com<mailto:kevin.ong at

Hello, I'm experiencing a strange early shutdown behavior with the following system: * */OS/*: Slackware Linux 14.2 x86_64 * */NUT/*: 2.7.4 (from my own package <https://sotirov-bg.net/slackpack/pack.cgi?id=4083>) * */UPS/*: MGE Ellipse PRO 1600 <powerquality.eaton.com/Products-services/Backup-Power-UPS/Ellipse-PRO.aspx> (bought in September 2017) */Problem

[please use reply-all to include the list - the headers are not mangled] On Oct 25, 2016, at 9:53 AM, Tomasz Przychodzie? wrote: > > Hi, > > Another beginner question. I spend hours trying to find the solution for how to configure winnut properly but I' struggling to make it work. I want my QNAP NAS TS-231 to work as a master and send signal to the PC to shut it down during

On Oct 26, 2016, at 4:56 AM, Tomasz Przychodzie? wrote: > > Level INFO 10/26/2016 10:46:17 Detected OS as Windows NT > Level NOTICE 10/26/2016 10:46:17 Network UPS Tools upsmon 2.0.0.4 > Level INFO 10/26/2016 10:46:17 Config Load: MINSUPPLIES set to 1 > Level INFO 10/26/2016 10:46:17 Config Load: NOTIFYCMD set to "c:\Program

Hey Guys, I figured someone might have use of this at some point. I've created an iRule for our F5 Load Balancer which performs the following tasks: - Appends STLS to the POP3 Capability list (it does this blindly, so expects the backend POP3 server to not return this) - Watches for the STLS command and initiates SSL negotiation with the client (leaves the connection to the

I am aware of 2 windows nut clients both interestingly called winnut. One (winnut 2.0.0b) is a service based client based on a port of the but client code (I think). The other is a GUI client based on (I think again) on knutclient . I have corresponded with both authors about a feature request - to allow the shut-down action to be (optionally) a windows hibernate. This seems a very

Hello everybody, After succeeded in "tuning" nut-2.0.0's hidups and 2.0.3's newhidups on customized Linux kernels, we are now facing a new challenge : trying to install nut-2.0.5 on a RedHat ES4 which is based on a 2.6.9 kernel. I picked up the 2.0.5 source package and follow the INSTALL doc until step 6. So far so good. RH ES4 is managed by udev, therefore I presume we

Hello, It is 3 or 4 weeks ago since, i want to set communication with my ups a MGE NOVA 1100 AVR. I do it first with manual configuration but after no success, i prefered to install mgeups-psp package to do it directly. But since when i execute psp, the attempt finish with an "No communication with UPS" error. Same is when i type: mge-shut -u root -DDDDDDDDDD /dev/ttyS0 . I unplog