similar to: 64bits bug? (was: my ups shuts down when starting upsd)

Hi, I have a Fenton Powerpal L660, when I try and configure nut with either the metatec or fentonups driver, and start upsd, the UPS instantly turns itself off. It used to work, until I changed my motherboard and CPU, which means it has a different bios and serial port setup. This is happening with Nut 2.0.1 and also Nut 2.0.5. I have an AMD64 bit processor, Mandriva 2007 64 bit. Any

Hi, Has anyone had success with the Dynamix 650VA, that uses the USB cable? I can't get megatec_usb to recognize it, I have tried both stable and development versions. Regards Glen Ogilvie

Network UPS Tools version 2.6.3 has been released: http://www.networkupstools.org/ Direct access: - Download: http://www.networkupstools.org/source/2.6/nut-2.6.3.tar.gz - News: http://www.networkupstools.org/source/2.6/new-2.6.3.txt - ChangeLog: http://www.networkupstools.org/source/2.6/ChangeLog Arnaud and the NUT team -------------- next part -------------- An HTML attachment was scrubbed...

Hi Volker Kuhlmann and Richard Nelson, As both of you are interested in where I got up to with getting my Dynamix 1000 VA UPS working with Linux, here is the details. It works.. But not too well, as the driver still seems to need some work, and is not in the main nut source as far as I know. It also seems to sometimes not respond when it should. The manufacture has uses the same format as

Hi there Would anybody happen to know the correct driver for a Fenton Powerpal S series? upsdrvctl reports: Network UPS Tools - UPS driver controller 1.2.2 Network UPS Tools - Fenton UPS driver 0.90 (1.2.2) Unknown ups - please report this ID string: #FENTON S Series V4.04EG503 Detected Unknown Series on /dev/ttyS0 Alternatively, does anyone know if the manufacturer is likely to

Here's a suggested change for receiver.c in version 2.5.2. It works in aix 4.3.3. *** receiver.c.org --- receiver.c *************** *** 427 **** ! rprintf(FERROR,"mkstemp %s failed\n",fnametmp); --- 427 ---- ! rprintf(FERROR,"mkstemp %s failed: %s\n",template,strerror(errno)); (Sorry, my version of diff doesn't seem to have the format I'm used to

Gidday all - I'm a new user to nut. I've got some cheap powerpal UPSs working fairly well. However I also have a new Dynamix UPS-1700D and an old Powercom KIN-1700 something unit that I cannot make work right. The best method I've found is "trial and error" which sounds a bit last-resort. Is there any better way to find out what protocol is used? -- Criggie

Hi Henning, you should get in touch with Carlos, who his developing a generic megatec driver (available from svn: http://eu1.networkupstools.org/source.html) Arnaud -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer - http://people.debian.org/~aquette/ OpenSource Developer -

Hi, I've got two Dynamix UPS's, both of which are USB and don't seem to work with NUT yet. Can anyone give me some advise on where I should start with working on getting them working. I can do a little C programming, so happy to give things a go but need some guidance. Brian R. Smith (who also subscribes to this list) has one as well. I've attached the output of lsusb -v and

We've used rsync with an old ssh for a couple of years with no problems. Now trying to switch to openssh 3.0.2p1 so we can use protocol 2. Rsync makes the connection via ssh and does it's work. The problem is after rsync runs and exits on the server side the sshd session keeps running and isn't closing the connection. So the rsync client hangs waiting for the connection to end. Is

We needed the group id bit to always be set on directories when rsync creates them. We always run rsync from a script with just the -ltR options. The destination file system uses acl's to control file access so new files need to inherit the properties of the directories they're in. (This is for IBM's global storage architecture on Aix or Linux). I made the following changes to make

Hi ups-devel, As I looked throw www.networkupstools.org site, haven't found any pointers where to send patches, so I hope this is the right place. (Please let me know weather this is the right place.) The patch contains a minor change in the logic of the driver, our Effekta MHD 3000 UPS continuously writes status data to the serial port, so one has to send a CR character and empty the

Hi, Installing a source package on Windows using utils::install.packages() with quiet=TRUE fails, while it works with the default quiet = FALSE. The problem seems to be caused by the fact that when quiet = TRUE, stdout and stderr are set to FALSE when calling "R CMD INSTALL" with base::system2() here:

Hi There, Running on debian sarge. This was working a while ago, but here goes.. When viewing the upsstats.cgi page, im getting a message "Not Supported" in the Model column with a "ONLINE" message, but no other stats. Here is the syslog when booting nut: Oct 15 14:28:40 mx1 upsmon[4835]: Signal 15: exiting Oct 15 14:28:40 mx1 upsmon[4834]: upsmon parent: read: Success Oct

The obvious guess would be that Rstudio is attempting something like redirecting output and getting itself confused. However, it is pretty clearly Their Problem, no? Rstudio has their own support infrastructure. -pd > On 26 Jan 2018, at 09:17 , Andreas Kersting <r-devel at akersting.de> wrote: > > Just noticed that this problem only occurs from within RStudio (v1.1.414). Any

Hi There, i have a strange problem with a fenton powerpal 660. When you switch off the power to the UPS (from the wall), the server (IBM xSeries 203) attached to it dies...However, if you unplug the cable from the server to the UPS and plug it back in again (with the power still out to the UPS), the server starts up again (set to power up after a power failure) and runs with no issues. I have

Hi all... I've tested my installation and everything seems OK, but I'll note a couple of things. System is debian, UPS is Fenton Powerpal 660 L First of all, the ups software did not restart because I had not changed 'no' to 'yes' in /etc/default/nut. Maybe it's a debian thing, I don't know. But I don't remember seeing it noted anywhere in nut docs.

Hi, I have a small problem with Samba in Debian 2.1 (Slink), kernel 2.0.36 and samba 2.0.5. I have a NT Server and a Linux client. I want to get some files from NT Server to the Linux client. They are in the same network and the IP's are: NT Server - 222.222.222.2 Linux Client - 222.222.222.40 Reading samba docs I discover two small utilities:

Hi! I've uploaded Samba 3.0.1 RPMs for SLES 8, SuSE 8.2 and SuSE 9 including some CVS fixes to ftp://ftp.sernet.de/pub/samba http://ftp.sernet.de/pub/samba Merry Christmas from G?ttingen, Volker -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 198 bytes Desc: not available Url :

Like Glen Ogilvie, I got a newer Dynamix 650 VA with USB connection, and was having trouble getting NUT to communicate with it. This appears to be the UPS that megatec_usb was built for - Vendor: 0x0001, Product: 0x0000, uses Megatec's software, has USB chip attached to internal serial lines, and has terrible USB implementation with fake HID tables. But megatec_usb would consistently fail.