similar to: MGE Nova AVR 600 USB on FreeBSD

Hello, It is 3 or 4 weeks ago since, i want to set communication with my ups a MGE NOVA 1100 AVR. I do it first with manual configuration but after no success, i prefered to install mgeups-psp package to do it directly. But since when i execute psp, the attempt finish with an "No communication with UPS" error. Same is when i type: mge-shut -u root -DDDDDDDDDD /dev/ttyS0 . I unplog

[the mailing list you want is nut-upsuser.] On Mon, Aug 3, 2009 at 8:05 AM, Blagovest Kolenichev wrote: > Hi, all > > I had fail to find in the supported hardware page > > http://www.networkupstools.org/compat/stable.html > > support for "NOVA AVR 625", but see that "NOVA AVR 600 Serial" > is supported. Can you tell us is there a big difference between

Hi, I have the above UPS connected to a FreeBSD 6.2 box and it shows 'data stale' very frequently (every few minutes). I have tried the usual trick of setting maxage, poll interval, etc etc but to no avail. When I wind up logging I see (on mge-shut) entering shut_get_report(id: 0d, len: 1800) shut_wait_ack(): ACK received entering shut_get_report(id: 16, len: 1800) shut_wait_ack():

Have recently purchased a MGE Nova 1100 UPS and am trying to get running on netBSD. Configuration netBSD 3.0 amd64 libusb 0.1.10a nut 2.0.3 Built & installed libusb Built kernel with ugen device and uhid removed Build & install nut-2.0.3 with usb Chmod /dev/ugen1 etc to allow access by nut user. Ups.conf [MGENova] driver = newhidups port = auto

I have nut 2.6.4-2.3+deb7u1 on debian 7 32bit, with UPS Eaton Nova AVR 1250 connected via USB. It happens several times a day that I get a message about Apr 3 16:41:49 kernel: [422581.049671] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 4 ret -110 Apr 3 16:41:54 kernel: [422586.041057] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 3 ret

On Apr 3, 2014, at 3:40 PM, Adam Pribyl wrote: > I have nut 2.6.4-2.3+deb7u1 on debian 7 32bit, with UPS Eaton Nova AVR 1250 connected via USB. Which kernel version? > It happens several times a day that I get a message about > > Apr 3 16:41:49 kernel: [422581.049671] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 4 ret -110 > Apr 3 16:41:54 kernel:

Hi, I'm having problems to configure upssched in order to notify me only when the disconnection exceeds the 30 seconds. Now, I'm getting a mail if it is disconnected just for a second, or even worse, when I got low tension. So, mail notifications are well configured, I guess... I think the problem is in upssched. I'm new to this, so it could be a stupid thing that I'm missing...

Hello, I'm facing problems as I'm installing NUT to monitor a MGE Ellipse ASR600USBS on a FreeBSD 6.1 box. UPS is recognized as : ugen0: MGE UPS SYSTEMS ELLIPSE, rev 1.10/42.41, addr 2 I'm temporarily using root profile (devfs/devd scripts not modified atm). newhidups starts & runs fine (unplugging mains makes newhidups outputs lots of data when started with -DDDD flags)

I have been testing out my new MGE Nova 1100 on a system (dual Athlon) running Fedora Core 5 and the newhidups driver seems to be regularly dying. The UPS is the USB model, I have nut-2.0.3-0.1.fc5 and nut-cgi-2.0.3-0.1.fc5 installed. I am running a 2.6.16 kernel. (I haven't upgraded to FC5's 2.6.17 kernel yet as there seem to be some complaints about it.) The driver initially works.

(Sorry, I accidentally discarded the wrong message in the moderation queue - please subscribe to the list to avoid this in the future.) > From: <onyx at netfusion.fr> > Subject: [HCL] MGE Pulsar Evolution 1100 - not recognized by USB driver > Date: December 22, 2011 12:15:16 AM EST > To: <nut-upsuser at lists.alioth.debian.org> > > > Hi everybody, > > It

Hi Vladimir, I have got 2.0.3 working on netBSD 3.0. To get it operational I needed to do the following (most of this is from memory...). 1). Recompile kernel with uhid removed. If uhid ataches to the device then libusb is not able to. Have to allow generic usb driver ugen to claim port. >From dmesg usb0 at uhci0: USB revision 1.0 uhub0 at usb0 uhub0: VIA Technologies UHCI root hub, class

Hello there. I've just install nut 2.2 from source on my FreeBSD box. I have an MGE AVR 600 UPS on a USB cable. Following the INSTALL instructions, everything works in term of the USB driver detecting the right UPS and upsd loads up and runs without error. However, upsc reports the following error: # upsc mge600 at localhost Error: Connection failure:Can't assign requested address

Hello, I've installed Nut (2.0.5) on RedHat a week ago, and upsmon seems to generate false alarms every hour: ... Jun 8 06:10:56 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on line power Jun 8 06:35:46 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on battery Jun 8 06:35:51 nutevalserver upsmon[2849]: UPS usb-mge-evolution at localhost on line power

Hi all, First of all thanks for the great work on nut ! (despite it's not fully functional yet overhere). Everything seemed to go fine until the final test : shutdown the UPS ! The system is running FreeBSD 5.3, the UPS is MGE Ellipse 800 USBS both linked with the MGE serial cable. The system is a remote server, only running some file services and large disks. The porting,

Hi, I'm using debian sarge on my server and connected a MGE-ups ellipse via the serial port. I searched the internet for the answer, but can't find it. My config files: <upsd.users> [admin] password = pwd allowfrom = 127.0.0.1/32 actions = set instcmds = all [upsmon] password = pwd allowfrom = 127.0.0.1/32 10.0.0.224/32 upsmon master [upsslave] password

Hello, I have Ellipse ASR 1500 UPS and now I'm trying to monutor it with NUT from FreeBSD. It seems that there are some problems with this UPS: =================================== ugen0: MGE UPS SYSTEMS ELLIPSE, rev 1.10/42.41, addr 2 > usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), NEC(0x0000), rev 1.00 port 1 powered port 2

The UPS is connected to the following environment: OS: Debian GNU/Linux 9.6 (stretch) NUT version: 2.7.4-5 Device output from lsusb: 0463:ffff MGE UPS Systems UPS Model name: MGE EllipseMAX 1500 URLs: http://powerquality.eaton.com/Products-services/Backup-Power-UPS/Ellipse-MAX-eol.aspx?cx=97&GUID=7BB6CD53-9F6D-4D62-B326-1099F137BF8D http://powerquality.eaton.com/68558.aspx?cx=97 The problem

Hi, I have had a long standing problem with NUT talking to 110V MGE UPSs on FreeBSD, I was recently investigating again and noticed that upsd seems overly noisy, eg.. May 5 03:50:36 egbert upsd[96662]: UPS [ups1] data is no longer stale May 5 03:50:36 egbert upsd[96662]: Data for UPS [ups1] is stale - check driver May 5 03:50:36 egbert upsd[96662]: UPS [ups1] data is no longer stale May 5

hello, at first I'm sorry my english isn't perfect but I tried to be clear I work with mandriva 2007 and with nut 2.0.1 installed with urpmi my UPS is a MGE Evolution 2200 connected with RS232 in my ups.conf I try to use mge-utalk driver and also mge-shut both seem to work I don't really known which I add to use It's the first point. As I saw on web site, I add maxage 25 in

I was testing my new MGE Nova 1100 and I am seeing negative numbers for ups.delay.start and ups.delay.shutdown which seems odd, but also seems to be expected according to examples I have found for MGE Systems. Can someone explain or point me to an explanation of what those numbers mean? The short descriptions don't appear to be compatible with negative numbers.