similar to: Problem with GeekSquad GS-1500 (Cyberpower 1500 avr lcd)

Hello All I have a MicroDowell ups (BBox BP 1000) connected to a Gentoo box by serial cable. If I try to start the driver , I see the following : Network UPS Tools - CyberPower text protocol UPS driver .05 (2.0.5) Warning: This is an experimental driver. Some features may not function correctly. debug level is '13' ups_sync: send [\rP4\r] ups_sync: got ret 46 [#1000VA

I know others have seen this before, I just never saw any real resolution to it. I am not a programmer, or at the least a very bad one, so I don't think this is something I can do properly myself. I have a Cyberpower 1500 AVR rack mount that worked good, except for the output voltage listing, with an older version of NUT (I don't remember the version of NUT, but the O/s was Fedora

Hi, I wanted to report some success with monitoring this UPS, a "Geek Squad" brand GS-700U that I purchased earlier this year from Best Buy Canada. Information about this... thing is very scarce so here is what I know: The unit itself is probably made by Cyberpower. It has a 9-pin serial port on the UPS, as well as a serial-USB adapter thing. I cracked open the serial-USB

We are interested in using Nut on our Federa 6.0 servers. However, our UPS systems are sold under the name "Geek Squad" (sold through the Best Buy chain of department stores). I'm pretty certain Geek Squad does not manufacture these units and they just rebrand them. Does anyone know who makes these units or what they are compatible with in terms of driver level protocol? The ones we

Hi, I want to set a make a contingency table which will look like this.. The problem is that I can't  set the table like the following.                      col1     col2       Total     row1              a         b         n10                      rp1       rp2        100                      cp1       cp2       rtp1   ---------------------------------------------     row2            

Hi there First a big thank you to all nut developers. I tried the 2.0.4 as well as the 2.0.5-pre1 versions with my CyberPower OP1000E connected to a serial to USB converter. All I got was the following: # /usr/local/ups/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.5-pre1 Network UPS Tools - CyberPower text protocol UPS driver .05 (2.0.5-pre1) Warning: This is an

Hi Recently i bought a MicroDoWell BP50, and with it followed a USB 2 serial converter. When i plug it into my 2.6.19 kernel, dmesg shows hiddev96: USB HID v1.10 Device [Cyber Power System CPS RS232 USB BRIDGE for UPS] on usb-0000:00:04.2-2 usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver So, i figured i should use usbhid-ups,

I checked Best Buy again. The second system I recommended is in stock at the Best Buy in Warwick. It's on sale for $353. :) http://www.bestbuy.com/site/olspage.jsp?skuId=8254569&type=product&id=1169512522677 I'm thinking about getting out of Dodge today to unwind so if you pick it up early today I can come up and help you install it and then just come home later in the day.

> -----Original Message----- > From: centos-bounces at centos.org [mailto:centos-bounces at centos.org] On > Behalf Of Alice Wonder > Sent: Sunday, September 25, 2016 1:40 PM > To: centos at centos.org > Subject: Re: [CentOS] How to move /var to another partition > > > > On 09/25/2016 10:23 AM, J Martin Rushton wrote: > > > > > > On 25/09/16

Hey All: I have a CyberPower OP1250 and I'm trying to mod the cpsups driver to work with it. I added the following lines to cpsups.c /* Added: Andrew Tubbiolo EXPERIMENTAL Aug 15, 2008 */ if(!strcmp(abbr, "#1250VA ")) { dstate_setinfo("ups.mfr", "%s", "CyberPower"); dstate_setinfo("ups.model",

https://bugs.freedesktop.org/show_bug.cgi?id=85570 alexander korolev <kilork at yandex.ru> changed: What |Removed |Added ---------------------------------------------------------------------------- Hardware|Other |x86-64 (AMD64) -- You are receiving this mail because: You are the assignee for the bug. -------------- next

I have an old (1997) Best Ferrups (model FE18KVA) that I am trying to monitor for the first time, but all the Best drivers fail to communicate with it. In ups_sync() in bestuferrups.c and bestfcom.c, the "time" command is sent and a one-line response is read. However, on my UPS, that command returns the current time and then prompts for a new time setting. I worked around that by just

I recently purchased a Cyber Power 700 AVR UPS. I installed it just fine and wanted to install NUT to monitor the unit. I searched the mailing list and found a similar post. However, the distro used in that post was different and the unit was slightly different (900 AVR). My server is running Debian Lenny. The Cyber Power UPS is connect to one of the serial ports using the cable that came with

Arjen, I read the following in the upgrade notes and just wanted to see what the status was for the cyberpower driver? The note reads: - The cpsups and nitram drivers have been replaced by the powerpanel driver, and removed from the tree. The cyberpower driver may suffer the same in the future. What does this mean to me -- a cyberpower user? -- David C. Rankin, J.D.,P.E. Rankin Law

Hello! I got my hands on a CyberPower 1500AVRT, and i'm trying to get it connected to my Gentoo machine. I've followed all the basic guides on setting up NUT and UPS' but have had no luck. My current ups.conf is: [cyberpower-gentoo] driver = cyberpower port = /dev/ttyS0 desc = Workstation Upon running /etc/init.d/upsd start or upsdrv start I get: * Starting

Arjen de Korte wrote: > Author: adkorte-guest > Date: Sun Jun 24 18:57:03 2007 > New Revision: 983 > > Log: > Make 'powerpanel' driver first choice for Cyber Power text and binary protocol UPS systems. > > Modified: > trunk/ChangeLog > trunk/data/driver.list > trunk/drivers/cpsups.c Is it OK to backport this into Testing, with the exception

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I've just noticed that cpsups isn't listed anymore in driver.list. Any reason not have removed it from the source too? Still on the way to 2.4; any update on your confidence level to remove nitram and cyberpower too? -- Arnaud

So I just bought one of these fabulous CyberPower UPS devices from BestBuy hoping I could control it with my machine. Luckily, I found NUT! I've got the SVN sources and compiled and installed them but I haven't been able to get it to recognize the usb AE550. When I plug the usb cable in I see this in syslog: Feb 6 22:36:56 mythbox kernel: usb 1-1: new low speed USB device using