similar to: Please Help for MGE NOVA 1100 AVR Serial configuration!

Hello, I want to manage my SMART APC with nut 2.0.3 on Fedora Core 4. But i have this output at start of my ups: D?marrage de apcsmart :Network UPS Tools (version 2.0.3) - APC Smart protocol driver Driver version 1.99.7, command table version 2.0 Detected Smart-UPS SC1500 [5S0713T66466] on /dev/ttyS0 [ OK ] D?marrage de upsd

Hi, I bought an Ellipse MAX 1100 a few months ago. First I attached it to my desktop and installed mge's personal solution pac. (a graphical interface which uses nut). It works. But I want to attach the ups to my server which runs without an x-server. I followed http://opensource.mgeups.com/install/debian.htm. Didn't work. Then I copied over the configuration files which the personal

Dear List, I thought it might be useful if I wrote up my notes on getting an MGE UPS to work with NUT and openSUSE. The MGE UPS (an Ellipse 1500 USB) will work well with NUT and openSUSE 10.2, but not "out-of-the-box": there are some things you need to do: Intro. MGE have built rpms of NUT which greatly simplify installation. Merci MGE. I used the rpm's for nut-2.0.5 and the

- UPS MGE Premium Ellipse Premium 1200 - SuSE Linux 10.0 OSS, kernel 2.6.13 smp - gcc version 4.0.2 20050901 (prerelease), glibc-2.3.5-40 - mgeups-psp-3.0.0-3, nut-2.0.2-4 - Dell Dimension 8400 with dual core Intel Xeon. 3.0GHz. lsusb shows: Bus 002 Device 003: ID 0463:ffff MGE UPS Systems UPS less /proc/bus/usb/devices shows for bus 2 device 3: T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=

I'll be back one more time perhaps I found the reason of these errors Nov 13 11:09:22 mezenc upsmon[3865]: Poll UPS [mgeups at localhost] failed - Data stale it happens when daemon upsd et upsmon are started after the boot obviously, there isn't any errors when upsd and upsmon are started at boot following later ... -----Message d'origine----- De : goudard sabine Envoy? : mardi

Hi, I'm having problems to configure upssched in order to notify me only when the disconnection exceeds the 30 seconds. Now, I'm getting a mail if it is disconnected just for a second, or even worse, when I got low tension. So, mail notifications are well configured, I guess... I think the problem is in upssched. I'm new to this, so it could be a stupid thing that I'm missing...

I have a SIP trunk from my Asterisk server to an Avaya CM server. If I place calls inbound, everything works fine. If I place calls outbound, originating from the Asterisk box, everything works fine (I have done this with the use of the .call files). If I setup an extension with the findme-followme feature and have it try to hair-pin a call back out the same trunk to the Avaya, I get a

Hello, I have installed mgeups (for Mge ellipse premium 500) in a Suse 10 x86_64 machine with yast2. But when I try to launch psp I receive the next error: psp: error while loading shared libraries: libgtkmm-2.4.so.1: cannot open shared object file: No such file or directory and don't start. The rpms installed are: mgeups-psp-3.0.1-3 nut-2.0.2-5 glibmm24-2.8.0-2 gtkmm24-2.8.0-2

Hi, I have a strange problem. At a site where there are 20+ phones, there is one phone that cannot make outbound (to PSTN) calls. Each call is dropped after 20s with "no response to our critical packet". Calls to voicemail and internal extensions work fine. I understand that everything points to a NAT problem, but I don't understand how it could be because: 1) It does not affect

Hello, I'm using NUT to manage a MGE Ellipse ASR UPS, with the newhidups driver. It works fine, except that after a few hours, I get a few errors from the kernel and the driver dies. Here's the output from the syslog: Apr 26 02:00:41 ezquiel kernel: usb 1-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110 Apr 26 02:00:43 ezquiel last message repeated 2 times

[the mailing list you want is nut-upsuser.] On Mon, Aug 3, 2009 at 8:05 AM, Blagovest Kolenichev wrote: > Hi, all > > I had fail to find in the supported hardware page > > http://www.networkupstools.org/compat/stable.html > > support for "NOVA AVR 625", but see that "NOVA AVR 600 Serial" > is supported. Can you tell us is there a big difference between

Hi, I have installed in suse 9.3 and ellipse premium 500 usb a psp 3.0 with yast2 and versions: nut-2.0.2-4 mgeups-psp-3.0.0-3 the first time that I launch psp it seems to contact the UPS and you can make changes to the parameters and all seems ok. If you make a reboot the psp hangs up and if you try /etc/init.d/ups it fails: Starting service NUT: -> Starting UPS driver: Network UPS Tools -

On Apr 3, 2014, at 3:40 PM, Adam Pribyl wrote: > I have nut 2.6.4-2.3+deb7u1 on debian 7 32bit, with UPS Eaton Nova AVR 1250 connected via USB. Which kernel version? > It happens several times a day that I get a message about > > Apr 3 16:41:49 kernel: [422581.049671] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 4 ret -110 > Apr 3 16:41:54 kernel:

Dear List, The driver usbhid-ups does not detect my MGE Ellipse 1500. I'm running openSuSE Linux 10.3, kernel 2.6.22 with mgeups-psp-3.0.4-2, nut-2.2.0-20 installed from MGE's rpm's. (Merci MGE!) lsusb shows: Bus 001 Device 004: ID 0463:ffff MGE UPS Systems UPS /etc/ups/ups.conf says: [myups] driver = usbhid-ups port = auto desc = "Local UPS"

Hi I try since a week to run my MGE Protection Center under Suse Linux 9.3. At the MGE site i found an HowTo. I have installed NUT an create the=20 configs but at boot the newhidups driver say=B4s "no USB/HID UPS found".=20= Anyone an Idea? Johannes Schatz=

Hello, I'm experiencing a strange early shutdown behavior with the following system: * */OS/*: Slackware Linux 14.2 x86_64 * */NUT/*: 2.7.4 (from my own package <https://sotirov-bg.net/slackpack/pack.cgi?id=4083>) * */UPS/*: MGE Ellipse PRO 1600 <powerquality.eaton.com/Products-services/Backup-Power-UPS/Ellipse-PRO.aspx> (bought in September 2017) */Problem

I have nut 2.6.4-2.3+deb7u1 on debian 7 32bit, with UPS Eaton Nova AVR 1250 connected via USB. It happens several times a day that I get a message about Apr 3 16:41:49 kernel: [422581.049671] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 4 ret -110 Apr 3 16:41:54 kernel: [422586.041057] usb 5-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 3 ret

Hello everybody, After succeeded in "tuning" nut-2.0.0's hidups and 2.0.3's newhidups on customized Linux kernels, we are now facing a new challenge : trying to install nut-2.0.5 on a RedHat ES4 which is based on a 2.6.9 kernel. I picked up the 2.0.5 source package and follow the INSTALL doc until step 6. So far so good. RH ES4 is managed by udev, therefore I presume we

All: I have recently discovered pxeLinux/memdisk and have been using them without alot of pain in a somewhat unconventional setup.. Win2k DHCP server and tftpd32 on WinXP. Don't throw rocks at me - you use what you've got. Anyways, thanks to HPA for a great tool. I am running into an odd little problem now for which I was wondering if there might be some remedy. On a particular

Hi, I've seen a few emails in the archives about problems polling MGE UPSs via USB under FreeBSD, but unfortunately I didn't find a solution in them that works for me. A few details about my setup.. The UPS is a MGE Nova AVR 600 connected via USB to a FreeBSD 6.2 box. I have tried both the nut port (2.0.5) and the svn trunk but have had no success yet. I am running nut as root to