similar to: bcmxcp_usb and powerware 5115

Hi Arnaud, Any luck with the latest subversion trunk? From: Greg Sent: Wednesday, May 13, 2009 10:34 PM To: Greg ; Arnaud Quette Cc: Kjell Claesson ; nut-upsuser at lists.alioth.debian.org Subject: Re: [Nut-upsuser] Nut and PowerWare 5115 Hi Arnaud, Some more testing on Ubuntu 9.04. Here is the output of bcmxcp_usb and lsusb ============================================ root at

Hi! all. I have been reading every mail and news about nut and 06da:0002 Phoenixtec but not found a solution. I have a very nice working ups from: CENER ref: "Active 1000VA 230V 12 CENER" and front logo "LA 900" It has COM3 and USB plugs, I don't know if it needs a standar RS232 I have test with varius drivers in ups.conf [MyUPS] driver = bcmxcp_usb | usbhid-ups |

On Dec 3, 2014, at 2:02 PM, janc at telefonica.net wrote: > USB error: error sending control message: Invalid or incomplete > multibyte or wide character This is a wild guess, but what about using the option "langid_fix=0x0409"? -- Charles Lepple clepple at gmail

Hi I try since a week to run my MGE Protection Center under Suse Linux 9.3. At the MGE site i found an HowTo. I have installed NUT an create the=20 configs but at boot the newhidups driver say=B4s "no USB/HID UPS found".=20= Anyone an Idea? Johannes Schatz=

Hi, I'm trying to get a Powerware 5115 to communicate with the NUT via USB under Debian Linux and need help. Here is the output that I see. co-nh5:/tmp/mnt/projects/pwusb/nut-2.4.1# /usr/local/ups/bin/upsdrvctl -u root start Network UPS Tools - UPS driver controller 2.4.1 Network UPS Tools - BCMXCP UPS driver 0.21 (2.4.1) USB communication subdriver 0.17 Communications with UPS lost:

Hi Please could someone assist me? I?e got a 3g usb dongle - Huawei E1552. [root@]# lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 03f0:8407 Hewlett-Packard Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus

Hello, I 'm trying to set up an Eaton PW5110 using nut-2.4.1 in OpenBSD, my ups.conf follows : [myups] driver = bcmxcp_usb port = auto desc = "Eaton PW 5110 (1500VA)" My first attempt to run upsdrvctl ended up complaining about unimplemented usb_clear_halt() in libusb. I patched libusb-0.1.12 with the following patch :

Hi Charles. I have got this output with driver usbhid-ups ups.conf [Phoenixtec] driver = usbhid-ups vendorid = 06da productid = 0002 port = auto #~ langid_fix=0x0409 desc = "CENER ONLINE 1000VA" # export USB_DEBUG=5 # ./usbhid-ups -a Phoenixtec Network UPS Tools - Generic HID driver 0.37 (2.6.4) USB communication driver 0.32 0.000000 debug level is '3' 0.000557

# export USB_DEBUG=5 # /usr/local/ups/bin/usbhid-ups -a CP550SLG -DDDDD Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 0.000000 debug level is '5' 0.000426 upsdrv_initups... usb_set_debug: Setting debugging level to 5 (on) usb_os_init: Found USB VFS at /dev/bus/usb usb_os_find_busses: Found 001 usb_os_find_busses: Found 002

Citeren "Daniel O'Connor" <doconnor at gsoft.com.au>: > usb_control_msg: 161 1 769 0 0x813310c 2 4000 > USB error: error sending control message: Input/output error > Can't retrieve Report 1: Input/output error > upsdrv_updateinfo... > Got to reconnect! > > usb_set_debug: Setting debugging level to 3 (on) > usb_os_find_busses: Found /dev/usb0 >

Howdy, I had this working with lots of help for a developer before (Charles Lepple), but after upgrading to a somewhat more current version of FreeBSD the patched-up version stopped working. Seeing as this was more than a few years ago, I thought I'd give a new libusb and NUT a try to see if it might work out of the box. So far, no luck. Some info: FreeBSD 6.3 libusb 0.1.12 NUT 2.4.1

I'm running FreeBSD 6.2 with Nut 2.0.5 installed from ports... I have a TrippLite OmniVS1500XL plugged in, but I'm having little luck with the tripplite_usb module. I have already built and booted a new kernel with UHID disabled so that libusb can grab /dev/ugen0. At first I was able to get the following out of the driver: # USB_DEBUG=5 /usr/local/libexec/nut/tripplite_usb -u root

Hi, folks! There is FreeBSD 7.1, NUT 2.4.1, UPS APC Smart 2200 XL. NUT is compiled from ports with following options: --------------------------------------- _OPTIONS_READ=nut-2.4.1_5 WITH_SERIAL=true WITH_USB=true WITH_SNMP=true WITHOUT_NEON=true WITHOUT_PDU=true WITHOUT_HAL=true WITHOUT_IPV6=true WITHOUT_CGI=true --------------------------------------- UPS is successfully recognized by OS

Hello, I have a Salicru UPS connected by USB using nutdrv_qx driver. As I see that it was using too much CPU time (or at least, too much for what I think it should be normal), I used strace to see what is was using, and got a lot of lines like these: %<------------%<------------%<------------%<------------ ioctl(4, USBDEVFS_REAPURBNDELAY, 0x7ffdca143278) = -1 EAGAIN (Resource

I recently purchased a Tripp Lite OmniSV1500XL and I've had no luck getting nut to work. # lsusb Bus 001 Device 001: ID 0000:0000 Bus 006 Device 002: ID 05e3:0702 Genesys Logic, Inc. USB 2.0 IDE Adapter Bus 006 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 005 Device 001: ID 0000:0000 Bus 007 Device 001: ID 0000:0000 Bus 004 Device 009: ID 09ae:0001 Tripp Lite Bus 004 Device

One small comment: When the driver has no permission to access the device, it exits with a segmentation fault, it would be nice to have a more informative error. I'm not really sure if the issue is speciffic to this driver or is it general. I attached the output of an strace with the driver crashing. Best regards. -------------- next part --------------

I used strace and the result is bus is busy: clock_gettime(CLOCK_MONOTONIC, {8158, 708518222}) = 0 timerfd_settime(11, TFD_TIMER_ABSTIME, {it_interval={0, 0}, it_value={8159, 708518000}}, NULL) = 0 ioctl(12, USBDEVFS_SUBMITURB, 0x40810) = 0 poll([{fd=7, events=POLLIN}, {fd=9, events=POLLIN}, {fd=11, events=POLLIN}, {fd=12, events=POLLOUT}], 4, 60000) = 1 ([{fd=12, revents=POLLOUT}]) ioctl(12,

Hi Sven, 2008/1/25, Sven Koch <haegar at sdinet.de>: > Package: nut > Version: 2.2.1-1 > Severity: normal > > I am using a Mustec PowerMust 1000 USB, connected with a USB cable to > the PC. > > With nut 2.2.0-2.1 everything works without problems - but since the > 2.2.1-1 update the "upsdrvctl start" from the init script just fails, > executing the

Hi Charles, I've been monitoring for the past few days and NUT has been running solid. Tested and everything's working as it should. Thanks for all of your help on this, great to have it running well again and learned lot. ________________________________ From: Daniel Shields <grungelizard9 at hotmail.com> Sent: Tuesday, October 25, 2016 8:01 PM To: Charles Lepple Subject:

I'm running Solaris 11 Express (snv_151a X86) with NUT 2.6.0 compliled from the source tarball and a Powerware 5115. I was seeing the driver hang, so gave it some '-D's (23 apparently ;-) and found that it seems to be getting into an infinite loop when reading data from the UPS. The debug output is attached and I would be very grateful for some help or advice on what to try next.