similar to: CyberPower 1500AVRT won't load driver!

Hi there First a big thank you to all nut developers. I tried the 2.0.4 as well as the 2.0.5-pre1 versions with my CyberPower OP1000E connected to a serial to USB converter. All I got was the following: # /usr/local/ups/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.5-pre1 Network UPS Tools - CyberPower text protocol UPS driver .05 (2.0.5-pre1) Warning: This is an

Hi, I've installed Nut 2.0.5 on a RedHat 9 box. I have a GeekSquad 1500 UPS. (GeekSquad is a BestBuy brand) I've found out that it's actually a CyberPower 1500 AVR LCD. I'm using it with the serial cable. I'm unable to get it working with any of the drivers provided with NUT. I've tried cpsups, cyberpower and powerpanel. here's the output of the different drivers

Hi Recently i bought a MicroDoWell BP50, and with it followed a USB 2 serial converter. When i plug it into my 2.6.19 kernel, dmesg shows hiddev96: USB HID v1.10 Device [Cyber Power System CPS RS232 USB BRIDGE for UPS] on usb-0000:00:04.2-2 usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver So, i figured i should use usbhid-ups,

Hello All I have a MicroDowell ups (BBox BP 1000) connected to a Gentoo box by serial cable. If I try to start the driver , I see the following : Network UPS Tools - CyberPower text protocol UPS driver .05 (2.0.5) Warning: This is an experimental driver. Some features may not function correctly. debug level is '13' ups_sync: send [\rP4\r] ups_sync: got ret 46 [#1000VA

This unit works fine with the "cyberpower" driver (which reports it as "Unknown model - 15"). It reads this much from it: battery.charge : 100 driver.name : cyberpower driver.parameter.pollinterval : 2 driver.parameter.port : /dev/ttyS0 driver.version : 2.2.0- driver.version.internal : 1.00 input.frequency : 60.2 input.voltage : 121 ups.firmware : 5.100

I recently purchased a CyberPower CP1200AVR UPS and am trying to get NUT 2.0.3 or NUT 2.1.0 to work with the newhidups driver, but am having little success. Before I purchased I did some googling and saw people talking about problems so I'm guessing it may not be supported yet? I did find some posts about people getting it to (sort of) work with some hacks, but couldn't tell if they

Arjen, I read the following in the upgrade notes and just wanted to see what the status was for the cyberpower driver? The note reads: - The cpsups and nitram drivers have been replaced by the powerpanel driver, and removed from the tree. The cyberpower driver may suffer the same in the future. What does this mean to me -- a cyberpower user? -- David C. Rankin, J.D.,P.E. Rankin Law

Hi, I wanted to report some success with monitoring this UPS, a "Geek Squad" brand GS-700U that I purchased earlier this year from Best Buy Canada. Information about this... thing is very scarce so here is what I know: The unit itself is probably made by Cyberpower. It has a 9-pin serial port on the UPS, as well as a serial-USB adapter thing. I cracked open the serial-USB

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I know others have seen this before, I just never saw any real resolution to it. I am not a programmer, or at the least a very bad one, so I don't think this is something I can do properly myself. I have a Cyberpower 1500 AVR rack mount that worked good, except for the output voltage listing, with an older version of NUT (I don't remember the version of NUT, but the O/s was Fedora

Hello, I'm a new to NUT and I'm having some setup problems. Here's my setup: Nut 2.0.2 Gentoo Linux 2.6.13-r3 CyberPower AVR900 According to the hardware compatibility guide this setup should work. Here's what I get: root@gentoo (0) [552] % upsdrvctl start Network UPS Tools - UPS driver controller 2.0.2 Network UPS Tools - CyberPower driver 1.00 (2.0.2)

All, I have a Cyberpower UPS that I have been working with for about a year. I have used NUT in the past with good results, but as of late have been seeing issues with nut talking to the UPS. I will start with the information on the server that is running NUT, and has the UPS connected VIA an RS232 cable. O/S : Fedora 9 Kernal (uname -a): Linux haruhi 2.6.26.5-45.fc9.x86_64 #1 SMP Sat

All, I have a Cyberpower UPS that I have been working with for about a year. I have used NUT in the past with good results, but as of late have been seeing issues with nut talking to the UPS. I will start with the information on the server that is running NUT, and has the UPS connected VIA an RS232 cable. O/S : Fedora 9 Kernal (uname -a): Linux haruhi 2.6.26.5-45.fc9.x86_64 #1 SMP Sat

Hey All: I have a CyberPower OP1250 and I'm trying to mod the cpsups driver to work with it. I added the following lines to cpsups.c /* Added: Andrew Tubbiolo EXPERIMENTAL Aug 15, 2008 */ if(!strcmp(abbr, "#1250VA ")) { dstate_setinfo("ups.mfr", "%s", "CyberPower"); dstate_setinfo("ups.model",

I'm looking for people that are using the 'cyberpower' driver that has been available for some years now. It seems the overhauled 'powerpanel' driver could support your UPS too. The commands and status bytes used are identical, the only difference being the way the values read for battery charge, temperature and frequency are interpreted. If we can find a way to detect when to

I'm looking for people that are using the 'cyberpower' driver that has been available for some years now. It seems the overhauled 'powerpanel' driver could support your UPS too. The commands and status bytes used are identical, the only difference being the way the values read for battery charge, temperature and frequency are interpreted. If we can find a way to detect when to

I recently purchased a Cyber Power 700 AVR UPS. I installed it just fine and wanted to install NUT to monitor the unit. I searched the mailing list and found a similar post. However, the distro used in that post was different and the unit was slightly different (900 AVR). My server is running Debian Lenny. The Cyber Power UPS is connect to one of the serial ports using the cable that came with

Hey all, I ended up picking up the module listed in Subject line. I switched over my config but apparently not all going smoothly. My config is: [office] driver = powerpanel port = /dev/ttyS0 desc = "Office UPS" When I test the driver running power-panel as a test, I get: > [root at cornelius init.d]# powerpanel -a office -D -D -D -D >

I've just noticed that cpsups isn't listed anymore in driver.list. Any reason not have removed it from the source too? Still on the way to 2.4; any update on your confidence level to remove nitram and cyberpower too? -- Arnaud