similar to: [PATCH] rescue: fix sscanf placeholders for --smp and --memsize

Argon2 is the default LUKS Password-Based Key Derivation Function (PBKDF) for some new guests such as RHEL 8.2 and Fedora. It is designed to be "memory hard", meaning that by design it requires large amounts of memory, making it expensive to brute-force. Unfortunately the default for guests which had more than a few GB of RAM at install time is to require about 1 GB of RAM to decrypt

These three patches (for discussion only, NOT to be applied) implement a mutex system that lets the user limit the number of libguestfs instances that can be launched per host. There are two uses that I have identified for this: firstly so we can enable parallel-tests (the default in automake >= 1.13) without blowing up the host. Secondly oVirt has raised concerns about how to limit the

Hi, I finally updated the Debian libguestfs packages: http://honk.sigxcpu.org/con/Libguestfs__Virtual_Machine_Image_Swiss_Army_Knife.html Sine we can't run the fuse tests easily in a chroot (since we might be unable to load the module) I'm using the attached patch to skip the tests if /dev/fuse doesn't exist. This probably isn't clean enough to go upstream though. The other

As you know, HVM save/restore broke recently because restored config miss guest memsize that used by xc_hvm_restore to locate some pfn. After discussion, we decided to remove the pfn deduction logic from restore side by adding a general memory layout. I have a patch for it. But then qemu broke, because it also require the memsize to locate the share page. We can''t use the previous

In data mercoledì 1 giugno 2016 02:04:33, Maros Zatko ha scritto: > --autosysroot option uses suggestions to user on how to mount filesystems > and change root suggested by --suggest option in virt-rescue. IMHO it should be called -i, like in the other tools, as what --autosysroot does is basically the same. > Commands are passed on kernel command line in format >

Depends on the previous 5 patches that modified virt-rescue to work without direct mode: https://www.redhat.com/archives/libguestfs/2017-March/msg00017.html Rich.

This supersedes the two previous patch series: https://www.redhat.com/archives/libguestfs/2017-March/msg00017.html https://www.redhat.com/archives/libguestfs/2017-March/msg00046.html Rich.

--autosysroot option uses suggestions to user on how to mount filesystems and change root suggested by --suggest option in virt-rescue. Commands are passed on kernel command line in format guestfs_command=command;. Command ends with a semicolon and there can be multiple commands specified. These are executed just before bash starts. On successfull run user is presented directly with bash in

--autosysroot option uses suggestions to user on how to mount filesystems and change root suggested by --suggest option in virt-rescue. Commands are passed on kernel command line in format guestfs_command=command;. Command ends with a semicolon and there can be multiple commands specified. These are executed just before bash starts. On successfull run user is presented directly with bash in

--autosysroot option uses suggestions to user on how to mount filesystems and change root suggested by --suggest option in virt-rescue. Commands are passed on kernel command line in format guestfs_command=command;. Command ends with a semicolon and there can be multiple commands specified. These are executed just before bash starts. On successfull run user is presented directly with bash in

Version 3: - Tidies up the code further. - Implements correct handling of SIGTSTP and SIGCONT. - Adds: ^] s - sync filesystems - Adds: ^] z - suspend virt-rescue Rich.

Hi everyone, lately I've been getting familiar with library and working on slight re-layering of the library. It's about having locking layer in public API and tracing one layer below that (let's call it __t_ layer. I'm not very good at making up names, so this is temporary:) ). Then making sure that all generated public stuff call __t_ layer and all other internal stuff

On 06/09/2016 03:18 PM, Pino Toscano wrote: > In data mercoledì 1 giugno 2016 02:04:33, Maros Zatko ha scritto: >> --autosysroot option uses suggestions to user on how to mount filesystems >> and change root suggested by --suggest option in virt-rescue. > IMHO it should be called -i, like in the other tools, as what > --autosysroot does is basically the same. We can call it

Hello, I was trying to understand the ELF file generated by the virsh dump (--memory-only) command. I have successfully generated a dump of the VM memory using this command. I specifically am trying to understand the loadable segments of this ELF file. I ran readelf -a <filename> to get the information that I need. Below shows the details of the loadable segments in a much better format

[Moving the conversation on @xen-devel and adding Jan, as that seems more appropriate] [Jan, this came up as I''m implementing some NUMA bits in libvirt but, as you see, the core of Jim''s question is purely about Xen] On lun, 2013-07-01 at 16:47 -0600, Jim Fehlig wrote: > On my non-NUMA test machine I have the cell memory reported as > > <memory

Alternate way to fix test-255-disks.sh running out of memory. See previous discussion here: https://www.redhat.com/archives/libguestfs/2018-May/msg00082.html Rich.

Instead of creating Guestfs handles and manually apply common options (e.g. debug and trace), use the open_guestfs in Common_utils. This also applies the common options to handles which didn't set them before, so we can inspect also their messages if needed. --- builder/builder.ml | 8 ++------ customize/customize_main.ml | 4 +--- dib/dib.ml | 4 +---

Make sure that -x enables tracing and -v enables verbose mode, just like other tools do. Kind of followup of commit b6b9b90dd74c7b9204bdf218aa9360e117308e78. --- builder/builder.ml | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/builder/builder.ml b/builder/builder.ml index a519913..0ddf076 100644 --- a/builder/builder.ml +++ b/builder/builder.ml @@ -555,7 +555,8 @@ let

Hi, I tried to rewrite virt-rescue from C to OCaml. Goals were feature parity with C implementation, smaller codebase and hopefully better maintainability. I still don't know if I've covered everything right. So, please check it out. PS: my git send-email seems to be broken, so I'm sending it from thunderbird Thanks! maros

https://bugzilla.redhat.com/show_bug.cgi?id=1175196 Currently if you write something like LIBGUESTFS_DEBUG=0 or LIBGUESTFS_DEBUG=true then it doesn't do what you probably expect. This patch series fixes that. Rich.