similar to: RAID1 migration - /dev/md1 is not there

Ok, this is the case: I've got two raid-5 arrays with software raid, both with three disks. Setup: md0 has hdb2, hdd1 and sda1 md1 has hdb5, hdd3 and sda3 Tonight, the system lost power due to a power spike. The result was a reboot where it attempted to fix the raid, but it didn't exactly work. I have now booted a live CD and using utilities there. It seems the checksum value is

I have configured 2x 500G sata HDD as Software RAID1 with three partitions md0,md1 and md2 with md2 as 400+ gigs Now it is almost 36 hours the status is cat /proc/mdstat Personalities : [raid1] md0 : active raid1 hdb1[1] hda1[0] 104320 blocks [2/2] [UU] resync=DELAYED md1 : active raid1 hdb2[1] hda2[0] 4096448 blocks [2/2] [UU] resync=DELAYED md2 : active raid1

Hi all, This morning I received this notification from mdadm: This is an automatically generated mail message from mdadm running on server-mail.mydomain.kom A Fail event had been detected on md device /dev/md1. Faithfully yours, etc. In /proc/mdstat I see this: Personalities : [raid1] md1 : active raid1 sdb2[2](F) sda2[0] 77842880 blocks [2/1] [U_] md0 : active raid1 sdb1[1] sda1[0]

Hi, I'm currently experimenting with software RAID1 on a spare PC with two 40 GB hard disks. Normally, on a desktop PC with only one hard disk, I have a very simple partitioning scheme like this : /dev/hda1 80 MB /boot ext2 /dev/hda2 1 GB swap /dev/hda3 39 GB / ext3 Here's what I'd like to do. Partition a second hard disk (say, /dev/hdb) with three

Hi. CENTOS 7.6.1810, fresh install - use this as a base to create/upgrade new/old machines. I was trying to setup two disks as a RAID1 array, using these lines mdadm --create --verbose /dev/md0 --level=0 --raid-devices=2 /dev/sdb1 /dev/sdc1 mdadm --create --verbose /dev/md1 --level=0 --raid-devices=2 /dev/sdb2 /dev/sdc2 mdadm --create --verbose /dev/md2 --level=0 --raid-devices=2

Hi list, I'm new with UEFI and GPT. For several years I've used MBR partition table. I've installed my system on software raid1 (mdadm) using md0(sda1,sdb1) for swap, md1(sda2, sdb2) for /, md2 (sda3,sdb3) for /home. From several how-to concerning raid1 installation, I must put each partition on a different md devices. I've asked times ago if it's more correct create the

System is CentOS 6 all up to date, previously had two drives in MD RAID configuration. md0: sda1/sdb1, 20 GB, OS / Partition md1: sda2/sdb2, 1 TB, data mounted as /home Installed kmod ZFS via yum, reboot, zpool works fine. Backed up the /home data 2x, then stopped the sd[ab]2 partition with: mdadm --stop /dev/md1; mdadm --zero-superblock /dev/sd[ab]1; Removed /home in /etc/fstab. Used

I am running software RAID1 on a somewhat critical server. Today I noticed one drive is giving errors. Good thing I had RAID. I planned on upgrading this server in next month or so. Just wandering if there was an easy way to fix this to avoid rushing the upgrade? Having a single drive is slowing down reads as well, I think. Thanks. Feb 7 15:28:28 server smartd[2980]: Device: /dev/sdb

Hello, Having a problem with software RAID that is driving me crazy. Here's the details: 1. CentOS 6.2 x86_64 install from the minimal iso (via pxeboot). 2. Reasonably good PC hardware (i.e. not budget, but not server grade either) with a pair of 1TB Western Digital SATA3 Drives. 3. Drives are plugged into the SATA3 ports on the mainboard (both drives and cables say they can do 6Gb/s). 4.

So I'm trying to RAID-1 this system which has two identical disks installed in it, and it isn't working for some reason. I started by doing a CentOS-4 install on /dev/sda1 as root, and with /dev/sda2 as my swap. I finish the install, yum update, and then I want to make the mirrors. I copy the partition table from one disk to the other: # sfdisk -d /dev/sda | sfdisk /dev/sdb I create

Hello All, on a Centos5 system installed with software raid I'm getting: raid1: raid set md127 active with 2 out of 2 mirrors md:.... autorun DONE md: Autodetecting RAID arrays md: autorun..... md : autorun DONE trying to resume form /dev/md1 creating root device mounting root device mounting root filesystem ext3-fs : unable to read superblock mount :

I have a large disk full of data that I'd like to upgrade to SW RAID 1 with a minimum of downtime. Taking it offline for a day or more to rsync all the files over is a non-starter. Since I've mounted SW RAID1 drives directly with "mount -t ext3 /dev/sdX" it would seem possible to flip the process around, perhaps change the partition type with fdisk or parted, and remount as

hi all! back in Aug several of you assisted me in solving a problem where one of my drives had dropped out of (or been kicked out of) the raid1 array. something vaguely similar appears to have happened just a few mins ago, upon rebooting after a small update. I received four emails like this, one for /dev/md0, one for /dev/md1, one for /dev/md125 and one for /dev/md126: Subject: DegradedArray

Received the following message in mail to root: Message 257: >From root at desk4.localdomain Tue Oct 28 07:25:37 2014 Return-Path: <root at desk4.localdomain> X-Original-To: root Delivered-To: root at desk4.localdomain From: mdadm monitoring <root at desk4.localdomain> To: root at desk4.localdomain Subject: DegradedArray event on /dev/md0:desk4 Date: Tue, 28 Oct 2014 07:25:27

Somewhere, mdadm is cacheing information. Here is my /etc/mdadm.conf file: more /etc/mdadm.conf # mdadm.conf written out by anaconda DEVICE partitions MAILADDR root ARRAY /dev/md0 level=raid1 num-devices=4 metadata=0.90 UUID=55ff58b2:0abb5bad:42911890:5950dfce ARRAY /dev/md1 level=raid1 num-devices=2 metadata=0.90 UUID=315eaf5c:776c85bd:5fa8189c:68a99382 ARRAY /dev/md2 level=raid1 num-devices=2

I have followed the procedure on the Centos page: http://wiki.centos.org/HowTos/CentOS5ConvertToRAID My setup is slightly different. I am using two partitions, / and /home. I have setup swap as a file, /home/swapfile. My hard drives are 500Gig sda and sdb. In modifying the instructions for initializing sdb I have: used /dev/md0 for / (sdb1) used /dev/md1 for /home (sdb2) In section 3.6 The

Hi all. I have a Dell SC440 running Centos 4.4. It has two 500GB disks in a RAID1 array using linux software raid (md1 is / and md0 is /boot). Recently the root file system was remounted read-only for some reason. The logs don't show anything unusual, presumably the file system was read-only before anythng was logged. Running dmesg showed this error repeated many times: EXT3-fs error (device

Hi I have a Raid 1 centos 4.4 setup and now have this /proc/mdstat output: [root at server admin]# cat /proc/mdstat Personalities : [raid1] md2 : active raid1 hdc2[1] hda2[0] 1052160 blocks [2/2] [UU] md1 : active raid1 hda3[0] 77023552 blocks [2/1] [U_] md0 : active raid1 hdc1[1] hda1[0] 104320 blocks [2/2] [UU] What happens with md1 ? My dmesg output is: [root at

Hello, i have a little problem. Our server has an broken RAID. # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sda1[2](F) sdb1[1] 2096064 blocks [2/1] [_U] md2 : active raid1 sda3[2](F) sdb3[1] 1462516672 blocks [2/1] [_U] md1 : active raid1 sda2[0] sdb2[1] 524224 blocks [2/2] [UU] unused devices: <none> I have remove the partition: # mdadm --remove

> Hi. > > CENTOS 7.6.1810, fresh install - use this as a base to create/upgrade > new/old machines. > > I was trying to setup two disks as a RAID1 array, using these lines > > mdadm --create --verbose /dev/md0 --level=0 --raid-devices=2 /dev/sdb1 > /dev/sdc1 > mdadm --create --verbose /dev/md1 --level=0 --raid-devices=2 /dev/sdb2 > /dev/sdc2 > mdadm