similar to: drbd

I am running a two-node web cluster on OCFS2 via DRBD Primary/Primary (v8.3.8) and Pacemaker. Everything seems to be working great, except during testing of hard-boot scenarios. Whenever I hard-boot one of the nodes, the other node is successfully fenced and marked ?Outdated? * <resource minor="0" cs="WFConnection" ro1="Primary" ro2="Unknown"

Hi all. I have two hosts with drbd: kmod-drbd83-8.3.8-1.el5.centos drbd83-8.3.8-1.el5.centos and kernel (CentOS 5.7): 2.6.18-308.4.1.el5 After a recent upgrade of kernel I have had two sitiuations when my ext3 filesystem on /dev/drbd0 became read-only. I've checked disks with smartctl -t long, they are ok. There are no messages with disks problems in /var/log/messages | dmesg. I've made

Hiya, I'm new to Centos but learning rapidly but I have been using FreeBSD. I'm trying to setup a HA NFS server using 2 machines. Both machines are running 4.3 updated to the latest via Yum. I did yum groupinstall drbd-heartbeat and yum install kernel-module-drbd-kernel-module-drbd-2.6.9-34.EL to match my kernel. The problem I have is that on 1 machine drbd works fine, but when I start

Hi, Sorry for the need of the long winded email. Looking for some answers to the following. I am setting up a xen PV domU on top of a LVM partitioned DRBD device. Everything was going just fine until I tried to test the filesystems in the domU. Here is my setup; Dom0 OS: CentOS release 5 (Final) Kernel: 2.6.18-8.1.4.el5.centos.plusxen Xen: xen-3.0.3-25.0.3.el5 DRBD:

We're trying to setup a dual-primary DRBD environment, with a shared disk with either OCFS2 or GFS. The environment is a Centos 5.3 with DRBD82 (but also tried with DRBD83 from testing) . Setting up a single primary disk and running bonnie++ on it works. Setting up a dual-primary disk, only mounting it on one node (ext3) and running bonnie++ works When setting up ocfs2 on the /dev/drbd0

We're trying to setup a dual-primary DRBD environment, with a shared disk with either OCFS2 or GFS. The environment is a Centos 5.3 with DRBD82 (but also tried with DRBD83 from testing) . Setting up a single primary disk and running bonnie++ on it works. Setting up a dual-primary disk, only mounting it on one node (ext3) and running bonnie++ works When setting up ocfs2 on the /dev/drbd0

Hi, i''ve a problem with drbd 0.7.10 module on an xenU OS (testing). I''ve compiling drbd with "make clean all" then "make install" without error. modprobe drbd OK with no error too and now and trying to start drdb /etc/init.d/drbd start Starting DRBD resources: can not open /dev/drbd0: No such device or address [ d0 can not open /dev/drbd0: No such device

Dear All, Currently using RHEL6 Linux and Kernel Version is 2.6.32-71.el6.i686 and DRBD Version is 8.3.10 DRBD is build from source and Configured DRBD with 2 Node testing with Simplex Setup Server 1 : 192.168.13.131 IP Address and hostname is primary Server 2 : 192.168.13.132 IP Address and hostname is secondary Finally found that drbd0, drbd1 mount failed problem *Found some error messages

Hi all, Where i want to arrive: 1) having two storage server replicating partition with DRBD 2) exporting via GNBD from the primary server the drbd with GFS2 3) inporting the GNBD on some nodes and mount it with GFS2 Assuming no logical error are done in the last points logic this is the situation: Server 1: LogVol09, DRDB configured as /dev/drbd0 replicated to Server 2. DRBD seems to work

Hi! I found a similar problem in an user maillist about my problem, but didnt work here. Im using a CentOS 5.2, with a Xen 2.6.18 kernel and a compiled Drbd 8. So, a load a ocfs2 module and use the mkfs.ocfs2 successfully with /dev/drbd0 But, when i try to mount it a take this log: # mount.ocfs2 /dev/drbd0 /mnt mount.ocfs2: I/O error on channel while trying to join the group # tail

Hello Everyone, I just ran fsck.ocfs2 on /dev/drbd0 which is a one gig partition on a vm with limited resource (100meg of ram). I am worried that the process crashed because it has not responded in the past hour or so? fsck.ocfs2 /dev/drbd0 fsck.ocfs2 1.6.4 [RECOVER_CLUSTER_INFO] The running cluster is using the cman stack with the cluster name ASTCluster, but the filesystem is configured for

Hi list. I am dealing with DRBD (+GFS as its DLM). GFS configuration needs a CLVMD configuration. So, after syncronized my (two) /dev/drbd0 block devices, I start the clvmd service and try to create a clustered logical volume. I get this: On "alice": [root at alice ~]# pvcreate /dev/drbd0 Physical volume "/dev/drbd0" successfully created [root at alice ~]# vgcreate

On Fri, Oct 21, 2016 at 02:24:37PM +0800, Liang Li wrote: > The implementation of the current virtio-balloon is not very > efficient, the time spends on different stages of inflating > the balloon to 7GB of a 8GB idle guest: > > a. allocating pages (6.5%) > b. sending PFNs to host (68.3%) > c. address translation (6.1%) > d. madvise (19%) > > It takes about 4126ms

On Fri, Oct 21, 2016 at 02:24:37PM +0800, Liang Li wrote: > The implementation of the current virtio-balloon is not very > efficient, the time spends on different stages of inflating > the balloon to 7GB of a 8GB idle guest: > > a. allocating pages (6.5%) > b. sending PFNs to host (68.3%) > c. address translation (6.1%) > d. madvise (19%) > > It takes about 4126ms

Hi! We operate a 2-node cluster running OCFS2 on top of DRBD. It shows about 4.3 GB free space on the OCFS2 filesystem using df on both nodes, but one node can't even write 10 MB: df (ouput identical on both the nodes) $ df -k /cluster Filesystem 1K-blocks Used Available Use% Mounted on /dev/drbd0 83883484 80071096 3812388 96% /cluster $ df -i /cluster

I have a pair of centos 6 systems, with a rather large raid thats DRBD replicated from box 1 to box 2... box 1 mounts this as /data when box 1 reboots, /data doesn't get mounted, but the drbd replication starts up just fine. the entry in fstab is... /dev/drbd0 /data xfs inode64 1 0 once the system is booted up, if I `mount /data`, it mounts just fine.

Hi Everyone, I''m trying to get Xen to use a native DRBD device but it seems it will not create the virtual machine. It does not seem to like the DRBD device type, any ideas on what might be wrong? I''m pretty sure my xen config file is OK and the DRBD device looks fine too. Full details below. xm create centostest Using config file "./centostest".

On 5/3/2016 2:52 PM, Clint Dilks wrote: > Are you using SE Linux? If so does the context for /dev/drbd0 match on > both systems ? afaik, this has nothing to do with the drbd slave. I reboot the master, replication resumes just fine, but the /data filesystem doesn't get automounted til I manually mount it. -- john r pierce, recycling bits in santa cruz

Hi guys I have few problems with live migration ... and I need some professional help :) I have 2 xen servers ... CentOS 5.3 and I want to have a high available cluster Now let`s begin .... xen0: [root@xen0 ~]# fdisk -l Disk /dev/sda: 218.2 GB, 218238025728 bytes 255 heads, 63 sectors/track, 26532 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start

centOs5.5/samba4/named here is a short guide setting it up to work. First of all do not install the bind package coming with centos 5.5!! Install needs for samba yum install libacl* gnutls* readline* python* gdb* autoconf* Named installation: Here is a description on what to do: http://jason.roysdon.net/2009/10/16/building-bind-9-6-on-rhel5-centos5-for-d nssec-nsec3-support/ The steps, yum