similar to: OT: hardware question

Fellow server-builders out there, this is for you. :) I was trying to build a cheap JBOD type storage solution running CentOS. Ended up snagging a Supermicro SC826TQ-R800LPB 2U case (12 drives slots) and a Supermicro X7DBE-O motherboard. Unfortunately, without thinking I snagged a 3ware 9650SE-12ML SATA RAID card which is a full height card and thus does not fit in my case. I have a few

hi there. anyone have any tips on params to pass to the kernel etc in order to install Centos4 or Centos5 32bit or 64 bit installed on this unit i can get it close to install, yet no cigar. it is a tyan MB and ill try to get more info if needed... for this case, please assume for now that the hardware itself is not "bad" thanks in advance... - rh Rackable Systems Dual Opteron 2.0

The systems will be operating the Center 5.2 32-bit, below the model, one will doubt that the system of controlling the media to do a RAID 0+1 PowerEdge SC1435 Processor AMD Opteron ? 2344HE Quad Core (1.7 GHz, 4x512 KB L2 cache, 1 GHz HyperTransport) - BRH8835 edit Memory 8GB Memory, 667MHz (4x2GB), Single Ranked Primary controller Integrated SATA Controller - No RAID edit First Hard Drive SAS

Hello I'd like to build myself an Asterisk server for SOHO use. Intel's D201GLY2 motherboard (http://tinyurl.com/ddarzp) looks like a very good deal, but I'm concerned about two things: 1. Will an A400P (from OpenVox, but supposed to be Digium-compatible http://tinyurl.com/ck6nfu) fit with a PCI riser, or will the CPU heatsink/fan be in the way? I downloaded the PDF from

I have a TDM400p with 3 fxs and 1 fxo daughter cards. It's in a mini-itx case with a 'right-angle' PCI riser card so the TDM400p is 'sandwiched' between the Atom D525 CPU and the 2.5" hard drive. I'm getting a bunch of clicks and pops on all ports. Has anybody had a similar experience? Did you find a solution? -- Thanks in advance,

Just to drag this thread on a bit further ... I've been looking into these little boxes, thinking I could use one as a firewall/gateway. My one requirement is that it would need to have two PCI slots (one can be low-profile), and although I've seen PCI riser cards that can give me two slots, they've been rare, and cases that are suitable (i.e have the space, and back panels are

Hello For those SOHO customers (ie. at most, a couple of POTS/ISDN connections and simultaneous SIP calls) who'd rather not use a big, noisy PC to run Asterisk, I'd like to offer an alternative that has the following features: - not old hardware sold on eBay, ie. it must be up-to-date hardware sold by a company currently in business - compact, silent - has room for a 2.5" hard-disk,

After having read this mailing list for a little while, I get the impression that there are at least some people who regularly experience on-disk corruption that ZFS should be able to report and handle. I?ve been running a raidz1 on three 1TB consumer disks for approx. 2 years now (about 90% full), and I scrub the pool every 3-4 weeks and have never had a single error. From the oft-quoted 10^14

Guys. Anybody using supermicro mobos and chassis with TDM cards? I would like to know which models are you using (mobos and chassis and also CPUs) and how many TDM cards have you been able to put in without having IRQ issues like in other cases. Ive read supermicro servers play nice with asterisk but it is always good to ask I guess. Thx! AK

On 12/25/2016 09:45 PM, Luigi Rosa wrote: <<>> > The other kind of server is sold both in "tower" and rack form factor; > they are bigger the airflow is forced by bigger fans that can turn to a > lower speed to exchange the heat. > > If the noise is produced by the rack fans, use, as someone else > suggested, variable speed fans regulated by a temperature

Hi, I'm looking for IBM hardware to support: 100 SIP hard phone users 10 fax machines on SIP ata's maybe later an additional 100 sip soft phones. Initially, all calls will be through PRI. Some conferencing. Don't know yet if this will even get used. Using 1.4 + ( probably business edition ) I'm looking for anyone who some experience / gotchas. I've google'd and

So, in the ongoing saga of the unusual 1U short-depth workstation, we have narrowed the field to two choices. Both entrants are configured with 16GB memory (4x4GB), two 2.5" drives (1x250GB SSD and 1x1TB HDD), and an NVIDIA NVS510 graphic card (quad display): 1) SuperMicro 5017R-MF, Xeon E5-2609 processor 2) SuperMicro 5017C-LF, Xeon E3-1220 processor (I wish SuperMicro had a list of their

Another day, another apparant unexplained hardware incompatibility. I have a TE412P and a TDM400B living quite happily in a whitebox using an Intel motherboard: http://www.intel.com/design/servers/boards/se7230nh1-e/index.htm I tried to move to an IBM x3650 system. It uses a slightly newer chipset, but apparantly it's in the same family. The SE-7230 board has been EOL'd and the

Hello I'm sure someone has already tried this: I use a couple of electric heaters to heat my office. I'd like to somehow connect them to Asterisk so that I could switch them on remotely by either calling the IVR or sending an e-mail to the Asterisk host, so that the room is warm when I get to the office :-) Any information appreciated. Thank you.

Hi, folks, Since I've gotten a total of one response in days on the HP forum, maybe the collective mind here has an answer.... As I've mentioned in other posts, we have an HP dl580 g5 that started throwing ECC errors. But wait, it's worse: memory is mirrored.... And the thing is fully populated with 32 DIMMs. I took my best guess, pulled the matching set of DIMMs, and took two

Hello all this is my first post to this list so i would like to than you all in advance for your time and consideration. I am in the process of building a new server and have purchased some used hardware. There seems to be some hardware issuses and i am hoping nothing was damaged during shipping. However i am in contact with intel and we are tring to figure out the exact problem via email. So

Hey, folks, I've got an HP Proliant DL580 G5 throwing ECC errors. This is annoying, since a) it's all new as of a few months ago, and b) it's *fully* populated. The two things I need to figure out are a) *which* DIMM it is, and b) is it mirrored; if so, which *other* DIMM needs to come out until we get replacements from the OEM. Here's one of many, all identical, from dmesg:

Hello, Digium uses the Dell PE 2850 for their testing. This site says that 3.3V PCI slot. http://www.voip-info.org/wiki/view/Asterisk+hardware We are planning on purchasing a Dell PE 2850 and putting a TE205P card on it. However, the needs a 5V PCI slot. Does Dell PE 2850 has a 5V PCI slot? A person in our group tried to call Dell's customer support but they do not seem to know.

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 49 bytes Desc: bullet.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050125/1dbc7ddf/attachment.gif

Hello, Some time ago, I noticed that whilst I had upgraded to Xen 3.1 (kernel 2.6.18-xen), I''d forgot to upgrade the paravirt DomU .cfg kernels from 2.6.16-xen to reflect this. So, I upgraded the DomU kernels & ran into issues with mounting devices, and the ext3 module not being available. After a bit of faffing about, I managed to sort this out and load the ext3 module.