similar to: external esata RAID box, how to spin down drives when idle?

Hi all! I've got a Venus DS3R Pro2 external drive unit with two drives set up as RAID-1, and the raid volume is formatted as ext4. it is listed in /etc/fstab as: UUID=f787c482-fb92-4ba7-87d6-cfeaef6b64c2 /mnt/backup ext4 defaults,users 0 2 if the external unit (which attaches via e-sata) is NOT powered on when the system boots, it hangs and drops to a maintenance prompt. I'd sure like

Had to replace dying cpu and mobo, so also replaced IDE with new SATA drive. Installed from latest ISO onto SATA and can't get networking to lease an IP address from my ISP (Comcast). The network utility always comes up with a private address (192.168.0.2) instead of Comcast IP. To add to confusion, if I boot into old IDE drive, I get proper network connection to internet, but lose my

After much head scratching and throwing most of a ream of paper into the trash, I just found and solved the problem. Thinking that perhaps I have a cable issue, I was re-seating the usb cable that connects my Xerox Phaser 3250 printer to the computer and realized that the printer was plugged into a USB 3.0 port on my computer. When I moved it to a USB 2.0 port, the printer immediately started

Hi all, my motherboard ma78gm is working. I am trying to get working the esata. I plug in my external driver, power cycle the external drive. then turn on my machine. My drive sda is detect as normal. however I dont see anything about any other disk. dmesg didnt show anything. Is there something special needed to activate the esata drive? Jerry

Does any one know how to, if at all possible currently, to export a block device via eSATA? i.e. how do I do something like iSCSI, but over eSATA? I have a cheat ($15 probably?) media player at home (Egreat EG-M31B Network Media Tank - awesome little machine) that runs some flavor of Debian and can be connected to any PC via eSATA as an external HDD's. i.e. it exports the built-in HDD as a

I am trying to get esata working. my lspci is below. When I plug in the disk an turn it on - dmesg reports nothing. Is it supposed to report anything like a usb disk does? Is there a module to load? My motherboard is GA-MA78GM-US2H. Jerry --------- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge

Hi, I'm looking for SATA controller with a eSATA port that is supported by Centos 4.4 ( rhel 4.4) Do you have any suggestions for a eSATA controller with good Linux support ? How can I list the sata controllers supported by Centos 4.4 ? Thanks JF Leblond Jean-Fran?ois Leblond jfleblond68 at hotmail.com _________________________________________________________________ D?couvrez

Hey, just bought an eSATA/USB dual drive docking station and my CentOS 5 can only see one drive at a time... Any one knows if there are specific parameters to set somewhere? Or do I need a more recent kernel (like upgrading to CentOS 6?) The docking is a Sharkoon Quickport Duo v2 + 2 drives + 1 eSATA cable... http://www.sharkoon.com/?q=en/content/sata-quickport-duo-v2 The eSATA controller is an

We've got this Dell server. In it, we've got two LSI HBAs. Mini-SAS to one RAID box. The other, cheapo RAID box, has eSATA. We got a mini-SAS-to-eSATA cable - actually, it's one mini-SAS to three eSATA. The systems sees not those disks. Will this just not work, with the HBA, or is there a driver that will let the what, mpt2SAS driver see the eSATA drives? mark

Has anyone ever triend to hang a eSATA drive chasis off oc a centos box? Not specifically this box, but something like this.... http://www.compsource.com/ttechnote.asp?part_no=DS1220&src=F I have used internal SATA drives on 3ware cards before without an issue. Didn't know if this was in the same arena. Thanks! Andrew

Is this possible? I want an external case with 4 HD in, each having an individual eSata cable. I plug in this case only when needed (each HD plugs into my PC separately), and do something like ">import ZFS pool" and use my ZFS raid. When done, I unplug it with ">export ZFS pool" or something similar command. This way I save energy, less noise, etc. I want it only as a

Hello, for quick harddrive tests (SMART, noise, backup etc..) I bought a very nice "docking" station connected to my ICH9 SATA controller (http://www.sharkoon.com/html/produkte/externe_gehaeuse/sata_quickport_pro/index_en.html) I can read/write to inserted disks, also smartctl works, but my favourite test doesn't run: diskinfo -t /dev/ad10 returns: ioctl(DIOCGMEDIASIZE) failed,

Hello all. Not sure how many people here also frequent the CentOS forums, so apologies for the 'cross post'. I know some here are using CentOS on HP's ProLiant Microserver, so if anyone's tried eSATA on their box, please let me know. Perhaps best to reply over at the forum - https://www.centos.org/modules/newbb/viewtopic.php?viewmode=flat&topic_id=31558&forum=39 Thanks

Hi list I am running out of space on my notebook. So wanna buy additional and external storage. I don't wanna do a DIY-work, so searching for pre-built external hard disks. I wish to buy Seagate FreeAgent Pro [0]. Does it work under CentOS 5? Would you recommend me even better products? I am searching for good performance, noise-less, smart standard support and no useless features like

Hi all, Does anyone know if this USB to SATA / e-SATA adapter will work on Linux? http://www.vantecusa.com/front/product/view_detail/266 Their website and knowledgebase doesn't say anything about it, so I'm checking the list to try my luck :) -- Kind Regards Rudi Ahlers

HI All, I have a dilemma and I would appreciate advice 1. Get a good size case, mobo, processor, etc and put 8 hard drives it in and RAID them. (yes an 8 port SATA mobo). Running CentOS. or 2. Get an eSATA enclosure that has room for 8 or 10 drives and just connect it to box? I know that RAID is not a full proof backup, but I am looking for a solution to store all of my data, projects, music,

Ok, got a quickie. I have an eSATA drive, a 750GB Seagate in an eSATA external enclosure, and a Silicon Image sil3132 ExpressCard controller for my laptop. The disk and controller work great in CentOS 5 (or F7, for that matter), if I specifically mount it. This is not how I want to have to use this drive, however. I want to hotplug it; that is, plug the controller into the laptop, and then

Hello Everyone, I have a CentOS 6.3 host running a few KVMs. One of them is a CentOS 6.3 KVM that I want to use for making backups with BackupPC. What I'm having a problem with is assigning the KVM an external drive. I used to run BackupPC on an Ubuntu box. The backups went to an external eSATA 1.5TB, ext4 format, single partition drive (regular 3.5" in an enclosure). I want to now

Hi All, I know Centos 5 is almost EOL and all this is old but.... I'm helping a colleague who has moved a Centos 5 install on an IDE disk to system with a Foxconn M'board. His idea is to use the SATA interface that's on the Foxconn. The thing boots OK and then gets into a loop trying to start the interfaces to the SATA disks. Oceans of stuff like this in /var/log/messages Aug 7

On 19/03/18 14:01, Morgan Read wrote: > Hello list > > I've been running the following command, first in fc20 and then now > (since the beginning of March) in fc26: > now=$(date +"%Y%m%d-%H%M"); sudo rsync -ahuAESX -vi /home/ > /run/media/readlegal/Backup/home > > /run/media/readlegal/Backup/rsync-changes_$now > > Since the move to fc26, this