similar to: I need some guidance to design my vpn.

ofcourse there is no freepbx, and there is no difference between the version of asterisk , ATM we are using asterisk 1.6.2.19 , i've also tried it on asterisk 1.10 , which resulted in the same way , does anyone have any ideas , why is it happening like this . thank you. On 9 January 2012 14:30, <tinc-request at tinc-vpn.org> wrote: > Send tinc mailing list submissions to >

actually at the moment the setup is like this , it has the same ip address , both lan and tinc , but iax doesn't work at all , moreover , i want to be able to make an IAX trunk to the rest of the machines from different networks together . what happens is that , asterisk says that the request is sent , but nothing will be received . if you want i can try to make a tcpdump tomorrow , and send

i need forwarding off , cause i need a central node , which is connected directly to all the network , directly , so it can usually upload content directly , without slowing down other nodes in the network , i also don't want it to act as a forwarder , since ,it only has 2mbps of bandwidth , and i don't want it for that purpose , is there any other way to fix this problem ? On 16 March

Hey everyone , I'm using tinc from iran , and i've been using tinc with tcponly for a few years now , to bypass the filtering , and have access to the free internet , but recently , our government started to apply some sort of exotic filtering scheme , they've completely blocked outgoing and incoming ssh requests , and ssl encrypted packets , and the only thing allowed is https !! ,

Hi everyone , i have a large network , connected together by tinc , and the whole network is connected so that i can access all the devices through out the networks simply and easily , but when i try to interconnect my asterisk servers usin iax , it doesn't work , if i try to register to my server using the tinc's interface it's ok, the registry is done ok , and the connection works

Hi everyone , i have a few questions/problems with tinc , which i need to address ASAP , so i'll make it brief . i have 33 sites , connected with each other using wan , in each site , there are two linux firewalls + 3-4 more servers , i preferred to have a full mesh within my network , but unfortunately it was not possible , when i wanted every site to be connected to every other , as the

Hi,Andy Thank your very much! For the MLPPP LFI,I found that in Cisco configuration,it use "ppp multilink;ppp multilink fragmentation;ppp multilink fragment-delay 20;ppp multilink interleave " command to enable MLPPP LFI.So I think just realizing the same function on my linux router would be fine.But I got no idea how to do this on linux.So is there anything with iproute2?Would you

Hi,all I am using iproute2/tc to manage bandwidth and control traffic.I must realize these two tricky functions in mips linux(kernel 2.4.17): 1.The device MUST support the capability to fragment AF and BE traffic in order to constrain the perturbing impact of AF and BE packets on EF traffic delay, for example using a mechanism such as MLPPP LFI.(RFC1990) 2. The packet size threshold before

Hi , today i was trying to connect my windows 7 client to my tinc server and i ran into a strange problem :) my tinc server is running tinc 1.0.11 on ubuntu 10.04 in switch mode , and the windows client is running tinc 1.0.13, there is a very strange problem , i tried to connect the windows system , i configured it , and it didn't work , so i ran it in debug mode -D -d5 , and it told me: Got

Hi , at the moment i'm managing a distributed network country wide , which i want to use tinc on all the machines so we can have direct access to all the servers (including those behind firewall) . the problem arises with the fact that , my firewalls are connect to two separate networks , one is actually a country wide network , and the other is internet access , is there a way , that tinc

Hi , I've added one node to my tinc mesh , with forwarding off , and the network got splitted into several pieces !!, the thing is that , the node with forwarding off is connected to all hosts , directly with connect to , and seems like that for some nodes the shortest path , that the tinc network can find is through the node with forwarding off , here are the results of my first ping to all

Hi all I have installed vyatta system, (vyatta-livecd-vc4-alpha2.iso ) on top of Centos5. Our system requirement is, * Centos 5.1 (2.6.18-92.1.10.el5xen ) * 2 Gb RAM, * x86_64 And cpu information is as follow, [root at turtle4 ~]# cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 15 model : 107 model name : AMD Athlon(tm) 64 X2 Dual Core

I have three ADSL lines that I''d like to use as one big pipe to the internet. The ADSL service works by establishing a pppoe connection (the ADSL "modem" is a bridge), and each pppoe interface gets its own IP address. This means I''d have to have 4 ethernet interfaces (3 for each of the ADSL modems and 1 for the LAN) in my gateway. I''d setup the gateway to NAT

Hi, I've got a client with two ADSL connections for redundancy. Is it possible to set up asterisk to connect to one SIP provider using both adsl connections and load balance between the two connections? Or to use one connection as the main one, and automatically fail over if the first connection drops? Or does this kind of thing need a serious network switch? Thanks Dan --------------

?I've a dovecot instance setup with submission proxy, protocols = imap lmtp submission sieve hostname = internal.mx.example.com submission_relay_host = internal.mx.example.com submission_relay_port = 465 submission_relay_trusted = yes submission_relay_ssl = smtps submission_relay_ssl_verify = yes service submission-login { inet_listener submission { address = 10.2.2.10,

Hi There, We currently using iproute2 for load balancing. However we need more upload speed as we load balance over 3 dsl lines. I''ve been looking for a way to combine the upload speed to more faster. Found a site called www.upstreaminter.net where these guys bond the adsl channels to improve uploads, Since downloading is problem as its need to know the ip address of the downloader they

Hey all - New to Ruby, though I''ve managed to stumble around in PHP (well, enough to hack together what I needed). I''ve initiated a (hopefully) simple project to keep track of upcoming stories in our newspaper. It''s a one-table database with just a few fields (writer, publication date, synopsis, notes, page assignment). I''m slowly replacing the default

Try http://www.rubyonrails.org/ -----Original Message----- From: rails-bounces@lists.rubyonrails.org on behalf of Michael Greenberg Sent: Sun 26/02/2006 21:26 To: rails@lists.rubyonrails.org Cc: Subject: [Rails] Newbie needs some guidance Hi folks, Im pretty much a newbie to Rails and I was wondering if anyone can point me in the way of tutorials and/or some good books.

Hi, all    I tried to search the web and can only find a little without details. I think maybe a lot of people here think it''s a piece of cake to create VM or template from scratch. But for newbie like me, it''s not that easy. If there is no suitable template in the XCP platform, it''s quite difficult for me to create VM as I wish.    I wonder if there is anything helpful

Hi can you please give guidance for generating future prediction values from existing heart disease data and we want to know the which type of models are using for generating the future prediction. can you please tell me how can i write the formula for future predictive values. can you see the following attachment and send me solution for that problem..... -- Thanks and Regards, Bala Chand