similar to: How to read RTP ports from CLI ?

Just like the subject sais - how expensive is it to execute a lot of these commands to keep track of different things in asterisk? I have avoided doing this because it feels a bit like a risk to spam the asterisk CLI this way, but is it really? CPU-wise it doesn't seem very expensive to do it 100 times a second (from a simple test I did), but is it possible it will affect the asterisk

We have a system where calls are coming in from telcos via an opensips server and then being redirected out to a regular sip destination. There is no NAT, DTMF features, call recording, or codec translation being performed so I would expect asterisk to issue a reinvite after the call is answered and switch the audio however it is not happening. Here is the sip peer information for the call

Hi all my asterisk server, 2 sip client softphones are the same LAN asterisk ip address : 192.168.1.5 sip client 1 : 192.168.1.4 sip client 2 : 192.168.1.2 asterisk starts ok with sip setup the sip.conf [test] type=friend username=test secret=1000 host=dynamic context=cucku directmedia=yes directrtpsetup=yes [1000] type=friend username=1000 secret=1000 host=dynamic context=cucku

Hi, I am using codec g729 on two asterisk machines, but when call is forwarded from asterisk server 1 (32bit) to server 2(64bit). server 1 outputs following error and there is no audio. Also the IVRs being played have choppy voice. "Insufficient information for SDP (m = 'audio 0000 RTP/AVP 18 127', c = '')" It is running fine when codec gsm is in RTP traffic. Also I

The latest revision of the draft RTP Profile is attached for review. This will be submitted to the IETF Audio-Video Transport Working Group for consideration immediately, so if you have any more comments, let us know. In addition, we will be applying for an official MIME type. Note that the AVP code and the MIME type in this latest revision have been changed from "SPX" to

>> The main idea is that Speex supports many bit-rates, but for one reason >> or another, some modes may be left out in implementations (e.g. for RAM >> or network reasons). What we're saying here is that you should make an >> effoft to at least support (and offer) the 8 kbps mode to maximise >> compatibility. > > I understood this. But as you may know: the

Hi, I would like to originate my first call from CLI. As I'm new to this, I'm wondering if it's possible. When I type "originate" from CLI, I've got this : " There are two ways to use this command. A call can be originated between a channel and a specific application, or between a channel and an extension in the dialplan. This is similar to call files or the

Hello, Is there a way to let someone access to Asterisk CLI and type whatever command (s)he likes but the shell command (the ones started by !) ? Ideally, it could be an argument to rasterisk: rasterisk --no-shell When done, a session could be like this: > pjsip show endpoints ... > core reload ... > !rm /etc/foobar Forbidden Suggestions ? Best regards -------------- next part

Do not forget to add the "Copying conditions" to the RFC. Check http://wiki.debian.org/NonFreeIETFDocuments That page contains a section titled "Template for RFC authors to release additional rights". To follow that guideline a section like the following should be added: x. Copying conditions The author(s) agree to grant third parties the irrevocable right to

Dear All, I am having some problems with connecting with a UA. Sometimes there is not sound in the call made, sometimes the caller would near no sound, while the callee can hear the caller. I have attached the rtp debug and sip debug for you comments. Please help me. Thank you all. Asterisk Version is 1.2.1 Asterisk RTP Range is 10000 to 20000 UA Listen RTP Port is 15000 Below is the the

Hello, Could you help me to summarize what is SIP Early Media useful for ? I was thinking of: - Passing error messages to caller, - Custom ringing tones to caller. Did I miss something ? Best regards -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20160203/33dec62b/attachment.html>

I receive an INVITE/SDP containing: m=audio 11310 RTP/AVP 3 0 101 which I interpret as gsm, ulaw, rfc2833. and I reply with an OK/SDP containing: m=audio 15884 RTP/AVP 0 3 101 which I interpret as ulaw, gsm, rfc2833. How can I tell which codec was actually used for the call? -- Thanks in advance, ------------------------------------------------------------------------- Steve Edwards

Hi, I succesfully install spandsp chan_misdn and digium card. the rxfax works fine and I get the fax result by email. I would like to do the same using a Patton gw + zaptel but I can't receive fax anymore, the call comes in from ISDN in the Patton gw, patton sends it to asterisk, asterisk run a macro to make a tif file using rxfax, the tif file is correctly created but with a 0 size the call

Hi, I was able to use Unsniff to validate that the incoming 20 byte payloads of audio from the downstream IAX2 trunk was definitely G.729a whilst Asterisk 16.13.0 transcodes to G.711a unnecessarily. Media is confirmed as having been negotiated as g729 on all four streams. Nuance with this call is that it's from a WebRTC client which doesn't transmit any audio, could this be influencing

Hi all, Please find below an updated Speex Internet Draft document. It would be good if we could book some time for discussion on Speex at the IETF meeting in Vienna (scheduled for 14th July). The cutoff for submission is 9:00am EDT, (GMT -04:00), 30th June. Comments and feedback welcomed! Regards Phil

Hi, I have 2 systems (A and B). I have an 800 number... when someone calls the 800 number it goes: IAX2-->A---IAX---B--->SIP PHONE However.. if the user calling the 800 number is a SIP user that is registered to A it goes: SIP--->A---IAX---B--->SIP PHONE This is the problem... when a call comes in from the IAX2 800 provider, things work fine... however if a SIP user registered to

Hi All, I posted this a couple weeks ago with no response, I'm hoping that someone will see it this time around and be so kind as to offer advice for resolving this issue (or point me in the direction of a better place to ask) "Some" (but not all) calls on one of our Asterisk boxes are being dropped in Voicemail -- only in voicemail -- after about 20 seconds with the error logged

Am I missing something here? I see if (needvideo) { /* only if video response is appropriate */ add_line(resp, m_video->str); add_line(resp, a_video->str); add_line(resp, hold); /* Repeat hold for the video stream */ } else if (p->offered_media[SDP_VIDEO].offered) { snprintf(dummy_answer,

Hi, I am try to configure Asterisk as PBX system with two interfaces as shown below. One interface pointing to the local subnet with a SIP phone and another interface pointing to the external ISP SIP Sever. SJPhone(X.X.141.32)<--------->(Y.Y.47.149)local-intf-|Asterisk|external- intf(Z.Z.247.106)<-------->(w.w.158.26)ISP-SIP-Server----OutsideWorld I am able to setup a call from the

Hi, I am facing an issue while testing the video mail service of Asterisk. I have two different setup on one setup client being used is Mercuro while on the other client is Android based. On the Mercuro setup video mail is stored and retrieved properly while with Android based setup video?mail is not stored (audio is through). Both the client?use H.264 codec with following sdp information: