similar to: Dimensioning asterisk 11

I have been trying to get a feel for scaling or dimensioning using asterisk 11. if I desire to use something like a dell r320, hardware RAID, 2G E5-2420, 4G RAM and only SIP trunking using gsm (least bandwidth and no transcoding) how many calls "out" can I expect to make at one time and asterisk still be OK and responsive? Thanks, Jerry -------------- next part -------------- An HTML

Is there a way on Dell R320 (two power supplies and hardware RAID-1) on centos to get a message that a power supply is failing or that one of the hardware RAID disks is failing? Sure there is the front panel - but no-one is there ... Is that reported to linux/centos some way? This is my first R320. Thanks, Jerry

Hi, I have installed CentOS 6.4 on Dell Server R320 64bit with UEFI BIOS. Do i need both /boot and /boot/efi partitions. Please help me understand the difference between these. Regards, Kaushal

Hi all ! Thanks for the very good support of Dell R320 hardware, perc H310 is well supported, BCM5720 seems to work correctly and performances are great. The only problem i have found is very strange. The FreeBSD bootloader take many times to load, 30sec-2minutes to boot the kernel and show the bootloader menu. After that, the system boots properly, at a normal speed. Is there any issue or

Hi I am evaluating some voice broadcasting solutions based on Asterisks for more than 1000 simultaneous calls. Connection to Asterisk all are based on SIP and SIP Trunks so no DAHDI hardware is required. According to some recommendations like http://osdial.org/howto/? "Internal timing is very critical with Asterisk when it is under load" and we must use DAHDI hardware or "USB Voice

This is... odd. Got a 6.8 box, a Dell R320 lspci tells me 01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2008 [Falcon] (rev 03) so it *should* accept an SAS drive. I've got a Cheetah that's a few years old, and having pulled it out of another server (in the datecenter), I put it in this box to zero it out for reuse... and the box refuses to see the drive. *Nothing* in

Howdy, I built an LXC container with an "image" of asterisk 11.18 precompiled and installed. It runs fine on the dev platform, which is a Dell R320 running Ubuntu 14.04LTS. I shutdown the container, tarred it up, and untarred on a Dell PE1850, also running Ubuntu 14.04LTS. The container itself is Ubuntu 14.04LTS. Both platforms as far as I know are amd64. The container boots

On 7/26/2016 2:38 PM, Peter wrote: > On 27/07/16 09:11,m.roth at 5-cent.us wrote: >> >This is... odd. Got a 6.8 box, a Dell R320 lspci tells me >> >01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2008 >> >[Falcon] (rev 03) >> >so it*should* accept an SAS drive. I've got a Cheetah that's a few years >> >old, and having

Have a new TE133 in a dell R320. dahdi_cfg -vvv shows: DAHDI Tools Version - 2.9.1 DAHDI Version: 2.9.1 Echo Canceller(s): Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 02: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 02) Channel 03: Clear

Hi, folks, This is a test post; to make it of interest, here's an issue you might want to be aware of, those with not brand new hardware. We've got a few Dell PE R415s. A 2TB b/u drive on one was getting full, so I went to replace it with a 3TB drive (a WD Red, not that it matters.) We got the system in '11. I built the drive - a GPT, 1 3TB partition, on an R320, from '12.

I am trying to install CentOS5 on a new HP DL360e G8 with B120i disk controller. It appears that a proprietary HP driver is needed for it. I found a useful description at http://www.linuxhelp.in/2013/08/Installing-centos-on-HP-Proliant-DL360e-Gen8-with-B120i-controller.html I have a pair of hard drives to use as a RAID1 mirror. My question to people who may have been this way already is: is it

I'm trying to determine the capacity of my host running Asterisk 11.8.1 on CentOS 6.5. The host is an Intel E3-1240v3 with 8GB RAM, an SSD, and gigabit Ethernet. The primary application will be bridging groups of users using meetme(). I'm using 2 boxes -- 1 to initiate calls using call files (box1), and 1 behaving a bit more like a production box -- bridging calls (box2). The call

Greetings Richard, To add to the above information, we are following the understated steps: 1. We have 2 BL460c (Gen8) with Fedora 21 installed. Both the machines(BL1 & BL2) have been updated with virt-v2v packages 2. On BL1, we execute the following commands: 1. virt-p2v-make-kickstart fedora 2. livecd-creator p2v.ks 3. After creating the

On 11/01/2015 12:07 PM, Karel Hendrych wrote: > Hi, just a heads-up: 3.18.21 didn't boot up on HP ML310e Gen8 v2, SATA drives in AHCI mode, / on software raid 1, no LVM. It ended up in kernel panic > with unable to mount root fs. Attached. No difference in grub kernel/xen settings. > > I didn't investigate the things deeper so far. 4.4.3-3/3.18.17 is booting fine. > >

On Sat, Oct 31, 2015 at 06:11:05PM +0000, Richard W.M. Jones wrote: > > On Sat, Oct 31, 2015 at 10:14:32PM +0530, Tejas Gadaria wrote: > > Hi, > > > > We are trying to do P2V conversion with virt-p2v. > > > > we have conversion server (virt-p2v) and physical server (virt-p2v) server > > configured as per below documentation. > > > >

Hi, We are trying to do P2V conversion with virt-p2v. we have conversion server (virt-p2v) and physical server (virt-p2v) server configured as per below documentation. http://libguestfs.org/virt-p2v.1.html#kernel-command-line-configuration After "Start Conversion" from GUI interface, we are conversion fails with "/run/lvm/lvmetad.socket: connect failed: No such file or

Hello, I am fairly new to Ruby and deployment. Have started creating a some apps and going through tutorials, etc. I am thinking about buying my own server like a HP ProLiant DL380e Gen8 Server<http://h10010.www1.hp.com/wwpc/de/de/sm/WF25a/15351-15351-3328412-241475-241475-5261094.html> to host and deploy my own web app which is a project management database where externals and

Hello, i'm trying to convert my physical web servers to a virtual guest. What i'm experiencing is a poor disk i/o, compared to the physical counterpart (having strace telling me that each write takes approximately 100 times the time needed on physical). Tested hardware is pretty good (HP Proliant 360p Gen8 with 2xSAS 15k rpm 48 Gb Ram). The hypervisor part is a minimal Centos 6.5 with

I have released to the master mirror the following packages for Xen4CentOS: b518e3b0fd4f735b34d7784815793cb787283d9029776bd9794cedeb274b9204 kernel-3.18.21-16.el6.x86_64.rpm 4b17373a0ef6806b26d02eb87fc299020beb60b6e31ed08a9c57d30a1410fbe7 kernel-devel-3.18.21-16.el6.x86_64.rpm cacedf6771849f7525145ad4ed7d36a2cad5b49b546173bb7c132b236cb7ac49 kernel-doc-3.18.21-16.el6.noarch.rpm

On Sun, Nov 01, 2015 at 09:23:28AM +0530, Tejas Gadaria wrote: > Hi Richard, > > Thanks for your replay, > > We are using Fedora 21 with SAS drive and RAID 0 config on both Physical > and conversion server. We're going to need a bit more information about the hardware in the physical server, like what 'RAID 0' means - hardware RAID? What precise RAID controller