similar to: PRI Error on span 1: Received MDL/TEI management message, but configured for mode other than PTMP

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

I have 2 ISDN BRI boxes, each with 4 spans, where the first one is configured as CPE, the second one as NET(so I don't need real lines for developing and testing). Once in a while I do see the following libpri error messages simultaneously on both boxes: PRI Span: 1 TEI=0 MDL-ERROR (A): Got supervisory frame with F=1 in state 7(Multi-frame established) PRI Span: 2 TEI=0 MDL-ERROR (A): Got

I have some more investigation to do on this, but I wanted to see if anyone here had any insight into the issue I've run into. The hardware is a HP DL360 G6 with a TE420 gen 5 4-port T1 PRI card. It is one of several systems that have been running without issue since 2010/2011. They have all been running CentOS 4 32-bit with Zaptel 1.4.12.1 (with patch for gen 5 card), libpri 1.2.8 and

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

In article <CAHZ_z=w5DMg93gShtC93kuC+fnmraPgV46BS956U5BQXVgyhxg at mail.gmail.com>, Matt Fredrickson <creslin at digium.com> wrote: > On Tue, Apr 3, 2018 at 5:44 AM, Tony Mountifield <tony at softins.co.uk> wrote: > > I have some more investigation to do on this, but I wanted to see if anyone > > here had any insight into the issue I've run into. > > >

Hi, As you may know, these ISDN BRI features are very important here in Europe as ISDN Basic Rate Access is very popular among Small & Medium Entreprises. I don't really know why but it seems that in many countries, default is to install small PBX using Point-to-Multipoint (PtMP) mode as opposed to Point-to-Point (PtP) which is the norm for PRI. So basically, in several countries, SME

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Hi, In BRI/TE/PtmP mode, pri show span 1 used to display "Type: CPE (PtMP)" (setup is bristuffed 1.2 asterisk) It seems, it displays now "Type: CPE" without any mention to PtMP (with asterisk 1.6). I'm far from 100% sure it used to include the PtMP word but do you think it should display it ? Does it make sense ? Regards -------------- next part -------------- An HTML

Hi list! We currently have a PRI gateway composed by a box with two Digium quad-span PRI cards (a TE420 and a ). One of the cards is filled with TELCO1, while the other has first two slots filled with TELCO2, and 3rd slot with TELCO3. I am currently having (timer ?) issues on TELCO3 (span 7) D-Chan (202 as determined by dahdi_genconf ) is constantly failing causing on-going calls to terminate.

Hi, In my lab, I'm testing BRI spans in NT/ptmp mode. My setup is: asterisk 11.2.1 libpri 1.4.14 dahdi 2.6.1 wctdm24xxp (HA8 hybrid with B400M) SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk <----> SIP phone The single BRI line I'm testing remains down: CLI> pri show spans PRI span 1/0: In Alarm, Up, Active I'm quite certain this

Hello, I have successfully installed MDL ISIS Draw 2.5 (a program used in chemistry) under Wine (0.9.12 in Debian). Now, I need to install an addon (AutoNom2000, which is used to give IUPAC names of compounds) for this program. (This addon requires Windows 2000/XP; Wine was configured to "mimic" Windows 98 by default). When I try to run its installer, I get the following:

Hey, I'm looking for a function which provides a supervised Fayyad & Irani discretization (MDL). I've already found RWeka which has such a function. But is there anything else? I'd prefer to use sth lighter in my own package. Regards, Peter

The Asterisk Development Team has announced the release of libpri 1.4.13. This release is available for immediate download at http://downloads.asterisk.org/pub/telephony/libpri The release of libpri 1.4.13 resolves several issues reported by the community and would have not been possible without your participation. Thank you! The following are the issues resolved in this release: * --- Outgoing

I have installed two HFC PCI A-cards running zaphfc from bristuff-0.0.2, which seems to work quite fine, but I continously receive the messages "D-Channel on span 1 up" followed by "D-Channel on span 1 down" with a few seconds interval. Why is that? Bri intense debug log and configuration files below. I don't need ztdummy or zaprtc, do I? I get some frame slips as well,

Hi, My setup is: IPPhone1 --- Asterisk1 with B410P ---- Patton 4638 --- Asterisk2 --- IPPhone2 I want to evaluate Asterisk1 in TE/PtmP mode. So, Patton box is configured in NT/PtmP (with 3 BRI links between both systems). Anyway, asterisk -rx "pri show spans" keeps replying : PRI span 1/0: Provisioned, Down, Active PRI span 2/0: Provisioned, Down, Active PRI span 3/0: Provisioned,

Hi, I've read that the new dahdi channel supporting B410P doesn't support PtmP when in NT mode. Does it support PtmP when in TE mode ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm

connecting legacy PBX to Asterisk (for the very same reason, those PBX use TE-PTMP). If others could join this thread and say if they agree or not with NT-PTMP being the 2nd most needed mode, would be great. Please, do not hesitate to comment. > > > Right now, I would not preclude the possibility that NT-PTMP support > might be added, but I could not give you a concrete time at which

Hi all, I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns QuadBRI running in NT-mode. Connected to the BRI-Ports are 12 Fax-Modems (Elsa MicroLink ISDN/TL V.34) which are only operating in dial out analog mode to deliver fax messages. After a while of running fine (50-200 dial out connections) on some S0 spans the following message occurs