similar to: Host = Dynamic in a Register Free Setup

I want to do something like: exten => _NXXXNxxxxxx,1,Dial(${BABY}/${EXTEN}) exten => _Nxxxxxx,1,Dial(${BABY}/${EXTEN}) exten => _1NXXNxxxxxx,1,Dial(${BABY}/${EXTEN}) exten => _011.,1,Dial(Dial({TOLL}/${EXTEN}) exten => _9NXXXNxxxxxx,1,Dial(${BABY}/${EXTEN}) exten => _9Nxxxxxx,1,Dial(${BABY}/${EXTEN}) exten => _91NXXNxxxxxx,1,Dial(${BABY}/${EXTEN}) exten =>

Hi all, While trying to track down a T.38 issue, I came across a series of log entries like this: ============================================================================ [Jan 26 10:23:31] WARNING[32508]: udptl.c:948 ast_udptl_new_with_bindaddr: Unable to allocate socket: Too many open files [Jan 26 10:23:31] ERROR[32508]: acl.c:488 ast_ouraddrfor: Cannot create socket

Hello Everyone, We are looking for a simple open source auto dialer with "polling" capabilities. What we would like is a program that we can upload leads to, and have asterisk: i) Dial numbers ii) Play pre-recorded iii) If user presses one, forward the call to an agent There are so many solutions out there it's hard to make a decision on what works, what has just a limited free

Hi all, A week or so down the list, i read that not many people were using realtime on an Asterisk18, so i had this afternoon a go at it... [sorry for the inconveneant line-wraps] First i did: mysql> create database asterisk; mysql> grant all on asterisk.* to 'voipadmin'@'localhost' identified by next i used the info from the wiki: CREATE TABLE `sip_devices` ( `id`

Hello Everyone, I have gone through a few really good tutorials from the OpenSIPS site, Asterisk resources etc.. The unanswered question (and final piece of our puzzle) is if it's possible to have a register free environment in an OpenSIPS/Asterisk integration. Most approaches have OpenSIPS relay the UA's REGISTER request to Asterisk which has "host=dynamic" set for the

Still a couple of questions...... I did configure extconfig.conf ... ;iaxusers => odbc,asterisk ;iaxpeers => odbc,asterisk ;sipusers => odbc,asterisk sipusers => mysql,asterisk,sip_devices sippeers => mysql,asterisk,sip_devices ;sippeers => odbc,asterisk ;sipregs => odbc,asterisk ;voicemail => odbc,asterisk ;extensions => odbc,asterisk ;meetme => mysql,general

Hello mailinglist, I want to connect Asterisk with OpenBTS and make a call with a mobile phone. I use: Ubuntu 11.10 + Kernel 3.0.22 GnuRadio 3.3.0 Asterisk 1.8.13 OpenBTS 2.8 Nokia Mobile Phone OpenBTS works and I can send sms from the OpenBTS server to the mobile phone. What I also need is a call between Asterisk and OpenBTS. I have also two soft phones which works with Asterisk. And also

Ok, i tried the suggestion: Instead of: sippuser => resource, database_name, table_name sippeer => resource, database_name, table_name I put in: sippuser => resource, context, table_name sippeer => resource, context, table_name Unfortunately, with the same results. btw i tried both "general" as "default" Besids the commands i tried below, isn't there any

Hi, list. We have a problem with loss peers after 'sip reload', our configuration: Asterisk 11.6-cert1, SIP realtime peers, sip.conf: - rtcachefriends=yes - rtsavesysname=yes - rtupdate=yes - rtautoclear=yes When we do 'sip reload' , peers are removing from available. Before `sip reload` : srv-pbx2*CLI> sip show peers Name/username Host

Hi All, I have a Polycom Handset on a front door and I'd like the phone to dial a number as soon as the handset is lifted without having to press and buttons or enter any numbers. I know how to do this on a Linksys but I can't find out how to do it on a Polycom. I would be greatly appreciate is some is able to tell me how this is accomplished. Regards David. -------------- next part

I am trying to use a simple tool in the Dial plan so that if the first number does not connect the logic will go to the second and/or third. Basically, I want the call to ring and connect to the first number Then, if it is not answered I want another number to try to get connected Then, if second number does not answer I want the third to be tried i only list the scenario for the first two

Hello, Our asterisk is connected to an ericsson pbx by PRI. What i want is the asterisk clients should call operator numbers by dialing 0 But, when a call is made to ericsson via number 0, it assumes that the call is made from outside, so it doesnt allow to be dialed. There are 3 real operator extensions which is grouped by ericsson for operators. Lets assume 1111 1112 1113. What i want to know

Hi all, I am configuring asterisk as a prepaid calling card. I am getting different local rate from my ISDN provider e.g 0.002 for landline and 0.13 for mobile etc. In this case I thing I have to say my asterisk/a2billing to bill based on local access number. so How can I retrieve called number (eg. 03-6832-1040 and 0120-272-060 is our ISDN PRI access number) to my asterisk server so i can

Hi, i need to match a number with like 03012345678*0 or 03012345*9 I tried _X.*X and _X!*X but both are maching 03012345678 too, ignoring that *X is required at the end. The interesting part is that like expected _X*X is matching only numbers like 1*1 and not 11 Regards Robert Wagner -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type:

It seems that for local channels (asterisk 1.4.33) the variable Variable: SIPADDHEADER="Alert-Info: Ring Answer" (call polycom phones and ring then auto answer) Is ignored, Is this just an oversite or is there some reason? It works fine with I call the SIP phone directly - however - when I first call the Local channel - then Dial the SIP phone the SIPADDHEADER doesnt seem to do

Has any one ever worked with placing idle display images onto the Polycom SPIP331 phones? I have got it working but when the image is displayed the clock is moved to the top of the screen. That is great but it scrolls between the clock and the registered extension(s) . Has anyone figured out a way to stop the scrolling and just display the time? If so could you provide me the configuration

Hi, I'm trying to install voicemail-imap support but there seems to be a missing module: imap_tk checking for mandatory modules: IMAP_TK... fail configure: *** configure: *** The IMAP_TK installation appears to be missing or broken. configure: *** Either correct the installation, or run configure configure: *** including --without-imap. My configuration Ubuntu 14.04 LTS Asterisk

when running asterisk -r, is there a way to turn off the messages? I didn't find the answer in the man page. thanks, Thufir

On 11 Mar 2015, at 17:53, Matthew Jordan <mjordan at digium.com> wrote: > On Wed, Mar 11, 2015 at 10:28 AM, Steven Howes > <steve-lists at geekinter.net> wrote: >> Anyone know where it?s gone?.. Appears to have been down all day. > The hamsters should be running in their wheels again now. Cheers Matthew. Give them some food from me. Steve

On Mon, 27 Apr 2015, Bryant Zimmerman wrote: > exten => _9XXXXXXX,n,Set(dialnumber=${l_HomeAreaCode}${EXTEN-1}) Missing a colon? ${EXTEN:-1} -- Thanks in advance, ------------------------------------------------------------------------- Steve Edwards sedwards at sedwards.com Voice: +1-760-468-3867 PST Newline Fax: +1-760-731-3000