similar to: [PATCH v3 0/7] support for cubieboard2 / sunxi processors

See http://www.gossamer-threads.com/lists/xen/devel/297170 for some information on how to get this going. I''ve rebased and addressed the review comments. As before several of the patches are not to be applied because they can be done better using infrastructure from Julien''s "Allow Xen to boot with a raw Device Tree" patch. They are included for completeness. With

The majority of this series went in a while back, what remains is just the basic platform support and the UART blacklisting. The series has also grown a constcorrectness fix for the other existing platforms too. Still no SATA support from upstream sadly. Bamvor has written some generic docs at http://wiki.xenproject.org/wiki/Xen_ARMv7_with_Virtualization_Extensions/Allwinner Thanks, Ian.

Besides single-port serial cards, also accept multi-port ones and such providing mixed functionality (e.g. also having a parallel port). Reading PCI_INTERRUPT_PIN before ACPI gets enabled generally produces an incorrect IRQ (below 16, whereas after enabling ACPI it frequently would end up at a higher one), so this is useful (almost) only when a system already boots in ACPI mode. Signed-off-by:

CID 1091471, Regression caused by 7c1de0038895cbc75ebd0caffc5b0f3f03c5ad51 This appears to be a typo which causes check_existence() to unconditionally return 1 in all cases. Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com> CC: Keir Frser <keir@xen.org> CC: Jan Beulich <jbeulich@suse.com> CC: Ian Campbell <ian.campbell@citrix.com> --- xen/drivers/char/ns16550.c |

On x86 ioremap() is not suitable here, set_fixmap() must be used instead. Also replace some literal numbers by their proper symbolic constants, making the code easier to understand. Signed-off-by: Jan Beulich <jbeulich@suse.com> --- a/xen/drivers/char/ns16550.c +++ b/xen/drivers/char/ns16550.c @@ -20,6 +20,9 @@ #include <xen/pci.h> #include <xen/pci_regs.h> #include

Since OMAP UART has a few distinct features than common 8250 UART, I re-implemented its driver rather than porting it based on ns16550.c. There are mainly two big differences between the implementations. First, OMAP UART introduces the concept of register access mode, which divides the register map into seperated space. Switching the access mode is then necessary when configuring it. Second, THRE

Prior to c/s 23811:f1349a968a5a LSR_THRE was checked only once, while there it got promoted into the surrounding loop''s condition. Since that bit may not clear for an extended period of time (i.e. when no new output is generated), it must not be used in this way indefinitely. Signed-off-by: Jan Beulich <jbeulich@suse.com> --- a/xen/drivers/char/ns16550.c +++

FYI, I see the following build error with this patch... MRJ ---- new warnings/errors for xen ---- keyhandler.c: In function `__dump_execstate'': keyhandler.c:96: warning: asm operand 1 probably doesn''t match constraints gmake[5]: *** [keyhandler.o] Error 1 gmake[4]: *** [/tank/ws/xvm-3.4.3/xen.hg/xen/common/built_in.o] Error 2 gmake[3]: *** [/tank/ws/xvm-3.4.3/xen.hg/xen/xen]

Hi Ian, I try compile the bootwrapper for cubieboard2 like this: joshzhao@joshzhao-ThinkCentre-M58p:~/project/Xen/A20/boot-wrapper$ make cubieboard2_defconfig CROSS_COMPILE=arm-linux-gnueabihf- # # configuration written to .config # joshzhao@joshzhao-ThinkCentre-M58p:~/project/Xen/A20/boot-wrapper$ make CROSS_COMPILE=arm-linux-gnueabihf- make -C scripts/kconfig -f Makefile.bootwrapper

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

The reset control API has two modes: exclusive access, where the driver expects to have full and immediate control over the state of the reset line, and shared (clock-like) access, where drivers only request reset deassertion while active, but don't care about the state of the reset line while inactive. Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting reset

Hi, > > > > +source "drivers/crypto/virtio/Kconfig" > > > > + > > > > endif # CRYPTO_HW > > > > diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile > > > > index ad7250f..bc53cb8 100644 > > > > --- a/drivers/crypto/Makefile > > > > +++ b/drivers/crypto/Makefile > > > > @@ -32,3

Hi, > > > > +source "drivers/crypto/virtio/Kconfig" > > > > + > > > > endif # CRYPTO_HW > > > > diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile > > > > index ad7250f..bc53cb8 100644 > > > > --- a/drivers/crypto/Makefile > > > > +++ b/drivers/crypto/Makefile > > > > @@ -32,3

On Sat, Aug 01, 2015 at 12:58:40PM +0000, Tal Lubko via Syslinux wrote: > Hi > > I would like SYSLINUX to get input from UART and act accordingly. > For example, I want to choose what rootfs to load according to the sequence received from UART. > So I'd like to know if SYSLINUX a the infrastructure for doing this Yes, Syslinux supports serial ports a.k.a. UARTS. Since the very

I am searching for the cheapeat *nix SOC device with ethernet and wifi that can run Python 2.7. Ethernet should be 100mbit and hopefully supporting PXE. OT because im doubting you can squeeze our bloaty friend onto such a device.... :)

# HG changeset patch # User john.levon@sun.com # Date 1190588448 25200 # Node ID 9a8a2d9ad94f20c995a7b59b75fdd6fefb8dafc6 # Parent 20c00448e39c7d8528e40287cafe614a5d4bdbf5 Default serial console to BAUD_AUTO Currently, the defaults for the serial console have a baud rate of zero, which is less than useful. Default to BAUD_AUTO instead, so you can just specify "console=com1" and it will

A call to drm_simple_encoder_init() initializes an encoder without further functionality. It only provides the destroy callback to cleanup the encoder's state. Only few drivers implement more sophisticated encoders than that. Most drivers implement such a simple encoder and can use drm_simple_encoder_init() instead. The patchset converts drivers where the encoder's instance is embedded in

A call to drm_simple_encoder_init() initializes an encoder without further functionality. It only provides the destroy callback to cleanup the encoder's state. Only few drivers implement more sophisticated encoders than that. Most drivers implement such a simple encoder and can use drm_simple_encoder_init() instead. The patchset converts drivers where the encoder's instance is embedded in

On Wed, 2007-12-05 at 14:22 +0000, Xen staging patchbot-unstable wrote: > # HG changeset patch > # User Keir Fraser > # Date 1196864460 0 > # Node ID f0ac46de680cc6fe8c91699fdda153b125ae515c > # Parent bf21e00155b7dd76653c5340099ecedac7a7de08 > [QEMU-DM] Upgrade emulated UART to 16550A. > > This patch adds 16550 emulation to qemu-dm. I still consider it a work > in