similar to: Dial plan flow control

I am dealing with a FreePBX generated dialplan. I have been following the processing traces attempting to make use of the advice I received here respecting setting a custom ring tone. I have discovered that the context I am using for incoming calls is not used at all during a blind transfer. Thus setting a third ring tone for that situation inside that context is an impossibility. I know now

I'm using FreePBX 2.5.2.2 with Asterisk 1.6.1.4. If I make a call and then decide to blind transfer them using ## my side of the call is not hung up. Instead it sends me to voicemail. If somebody calls me and then I blind transfer them with ## I am hung up on as expected. I called from 8678 to 28688. I then transferred the call to 8532. Asterisk acts like it wants to hang up, but then

Arch = x86_64 OS = CentOS-6.4 (freepbx) Asterisk = 11.4.0 FreePBX = 2.11.0.2 We use Snom870 handsets with firmware v.8.7.3.19. I am trying to develop a custom dial plan to invoke a distinctive ring-tone when an external call is transferred internally. Based on an earlier solution I discovered I am attempting this: [from-internal] include => set-alert-if-local [from-internal-original]

Hello all, I have a system running AsteriskNOW with asterisk asterisk-1.8.8.1-1_centos5 from AsteriskNOW repository. I just changed our Polycom 335 sip.conf so that blindpreferred=1 (all transfers default as blind transfers). If a customer calls in & we answer & transfer, everything works fine. But if we call out to a customer & then transfer to another internal extension, that

Whenever I try to drag calls to the Parking Lot or On Hold, FOP would drop my calls. I have searched online and have found similar problem, such as the link below. I have tried their solution but still the FOP is not working correctly. I even installed the HUDLite server and is getting the same results. www.freepbx.org/forum/freepbx/users/flas...ot-transfering-calls Here is the log when I tried

I've got a piece of CPE equipment that has an FXS port that I have tied to an FXO port on a TDM400 clone card. Normally, if I go off-hook with a standard telephone connected to it, I get a dialtone. If I dial a digit, and send a hookflash, the device will provide a dialtone back for the next available channel on the device. I'm trying to recreate this same behavior with Asterisk,

Hello. I am running Asterisk v1.6 on Ubuntu 10.10 with FreePBX v2.8. When I call the voicemail for any of my extensions, the call just dies. On a softphone, I get no sound whatsoever; it just hangs up after a couple of seconds. On my handset attached to my SPA-3102, it get a sound like when you leave an analogue phone off the hook. I have three extensions setup and they all do the same thing.

I have thsi code in a dial plan. The purpose of which is to set distinctive ring tones for internal and transferred calls. exten => _.,1,Noop(CALLERID_ALL=${CALLERID(all)}) exten => _.,n,Set(CallerIDNum=${CALLERID(num)}) ; This just shows a list of interesting variables and their values ; Comment it out when finished debugging ;include => macro-dumpvars ;exten =>

I am using Asterisk 11.17.1 with my program that uses AMI Originate calls to generate a bunch of calls for a callcenter. The PBX configuration is handled by FreePBX 2.11. I want to understand the dialplan behavior in order to figure out why the CDR(recordingfile) is blank on the CDR records despite the dialplan setting it. My program generates the calls by setting Channel=Local/NUMBERTODIAL at

Hi, We are using asterisk 1.4.34, ubuntu 10.4, below is suspicious activity recorded in our full log. Could you help us to explain what had happened. Thanks. === my friend, 801, from his room did a test by dialing echo test in freepbx, *43: [Aug 20 14:42:46] VERBOSE[14427] logger.c: -- Executing [*43 at from-internal:1] Answer("SIP/801-000003f5", "") in new stack [Aug 20

Hello, I have a system with two cards: a HFC-PCI ISDN and a TDM21B (2 FXO and 1 FXS), running Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1l with freePBX beta5 dialplan. I have connected an analog phone to TDM FXS port, but when I pickup the phone to make a call, Asterisk "hangs up" the call. Let me explain: In another system, when I pickup the phone, Asterisk give me tone to dial: >---

Hi all, I'm new in asterisk and I got to set up a dundi config for my work. I have 2 PBX for the test, the two PBX are in the same local network PBX A : 192.168.199.23 PBX B : 192.168.199.21 my config files : (on PBX B , the config files on PBX A looks like it) /etc/asterisk/dundi.conf [general] bind=192.168.199.21 port=4520 cachetime=5 ttl=32 autokill=yes entityid=00:30:18:4C:33:53

Here is the current dial plan section: [custom-michael] exten => _900,1,Playback(custom/extn-xfer) exten => _900,2,SayDigits(${EXTEN}) exten => _900,3,MixMonitor........... exten => _900,4,Dial(SIP/${EXTEN}|${DEFRT}) exten => _900,5,Playback(custom/extn-xfer2) exten => _900,6,Goto(custom-michael,901,4) exten => _901,1,Playback(custom/extn-xfer) exten =>

Hi all, I've recentrly starting to play around with *, when all I wanted is to configure an fritz ISDN card with A@H. Currently I'm stuck at the phase of what do I do with capi after everything is installed. I'm trying to understand how to setup incoming and outgoing calls at A@H since I'm getting a bit lost with the default dial plan. It seems that * answers but disconnect

I have two servers, each connected to the PTSN via PRI. When I call from site A (951-999-9999) to site B (555-1212) and the phone at site B is on the phone, I hear the normal ring tone for about 20 seconds, then the message "all circuits are busy now. please try your call again latter" followed by the congestion tone. Instead, I want this to busy ring and then hang up without any

I have this code which was taken from the phpagi project page along with the following in extensions_conf and the output from the asterisk CLI. When I call the 311 extension, I does nothing then hangs up. What am I doing wrong?? ----php code------------ #!/usr/local/bin/php -q <?php set_time_limit(30); require('phpagi.php'); $agi = new AGI(); $agi->answer(); $cid =

Hello list! I?m having an issue when reloading Asterisk, I?ve had this problem in Asterisk 1.6.1.6 so I upgrade to 1.6.2.1 version, but I still have the same error. For example, I send a "reload" in Asterisk CLI and this is the output: isb152*CLI> reload == Parsing '/etc/asterisk/extconfig.conf': == Found == Parsing '/etc/asterisk/manager.conf': == Found

Hi List, I have another issue on allowing outgoing calls to PSTN on Asterisk via Avaya Phones, I hope that anyone could help me fix this issue: *When I dial through Avaya phone i just here a "good bye message" reply from asterisk server. And here is the log:* == Starting OOH323/(null)-b7db8aa0 at internal,s,1 failed so falling back to exten 's' == Starting

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

Hi Everyone, Using Elastix (FreePBX + Asterisk 1.4.2x combination) with Aastra phones, how can one receive distinctive ring tones for INTERNAL calls ONLY? Even though FreePBX Inbound has an option for Alert_INFO but that doesn't work when the call comes into an IVR or Queue. The calls has to go directly to extension for external ringtone to be different. So, I am looking for internal calls