similar to: One resource immediately after another

Some of the Red Hat Enterprise Linux servers in our environment sometimes get assigned virtual IP addresses (eth0:1, eth0:2, etc). Puppet Dashboard''s parameters seem like an ideal way to define and provision virtual IPs on these servers. One could create a "vip1" parameter on a node, and define a value of the IP address to use for that vip. A manifest could then be written to

I''ve been using Puppet now for a month or so and I''ve come to a problem that may warrant an additional Puppet metaparameter. I''m advocating the addition of a metaparameter called "preaction" (or something like that), which will perform some arbitrary action before the resource is modified. There may be a way to do this within Puppet already (with some

Hello all I am setting up a Centos 6 machine with one network card & one onboard network port. Both are recognized & work. Onboard Network port is unused yet, but is required for dedicated access to LTSP LAN, which would allow older PIII machines to boot from this system. I have installed LTSP but again Networking seems to be the problem area, as the clients won't boot from this

I want to change the contents of my /etc/sysconfig/static-routes-ipv6 and NOT restart the network. Is there a way to do this??? I know about ifup and ifdown for interfaces, but what about routing (and IP6 at that).

Hi Guys, I want to create multiple virtual interfaces on a system running linux 2.6. The main requirment being, to assign unique MAC address fo each of the virtual interfaces. I need to know, if this is possible and will really appriciate if someone can provide me pointer in this direction. Thanks a lot. R. Singh _______________________________________________ LARTC mailing list

I have a series of static routes in route-eth0 Recently I had to made changes and could not find an effective way to get the old routes out and the new routes in. ifdown-route seems to apply the content of route-eth0 to take down the routes listed and ifup-route brings up routes based on route- So what ends up is that the old routes never go away, just new routes added. ifdown eth0; ifup

If eth0 holds virtual IP as its secondary IP and I bring down eth0 by command "ifdown eth0", CTDB will automatically pull eth0 up. Sometime it goes wrong. The virtual IP becomes primary IP, and origin primary IP turns into a secondary IP or just missing. If the origin primary IP is missing, I have to run "ifup eth0" though CTDB has pulled eth0 up. CTDB uses “ip link set eth0

Hi I;ve trixbox installed with 2 NICs. One NIC carries the MPLS-VPN traffic (only a 1 MB link without internet for carrying voice to another site) while the other NIC has a connection with public IP for internet services on that machine. the first NIC (eth0) has IP of 172.16.0.1 and is connected to router with WAN IP: 10.18.6.254 , the second IP is 203.234.82.98 (eth1). i want to have the

My manager tells me a system in the datacenter is down. I go down there, and plug in a monitor-on-a-stick and keyboard. It's up, but no network. I try systemctl restart NetworkManager several times, and ip a shows *no* change. Finally, I do an ifdown, followed by an ifup, and everything's wonderful. My manager thinks that the NM daemon thinks everything's fine, and there've been

Dear developers! I''ve found that recent xen releases cannot be simly run on openSUSE! The script /etc/xen/scripts/xen-network-common.sh makes some incorrect assumptions on the SuSE ifup script. Bridged xen networking only works if the script executes this branch: preiftransfer() { true } ifup() { false } ifdown() { false } Otherwise the xen networking scripts fail to put the

I recently reconfigured some CentOS 4.3 systems that were using DHCP to use static IP addresses. At the same time, the systems were moved to a new VLAN. Here is the approximate sequence of events that took place: 1. ifdown eth0 2. edit /etc/sysconfig/network-scripts/ifcfg-eth0 with static IP address 3. wait for network folks to reconfigure switch 4. ifup eth0 I may have

hi, I seem to have a problem with the Linux xen-network driver leaking skbs. This is probably my own fault, upon resumption after migration I call this: void network_resume(void) { struct net_device* dev = __dev_get_by_name("eth0"); MOD_DEC_USE_COUNT; network_open(dev); } -- which works fine. However, in network_open() the call to NETOP_RESET_RINGS seems to clear all the

Hi, This is a Centos 5.5 host with one xen guest. About 2 weeks ago, the host randomly lost network connection. By this I mean I could not connect to the services on it, or ping it. Also was the status of the guest. From serial console, I connected to the host, trying to see what happened. No clue (any error messages) in messages or dmesg. ifdown/ifup the interface did not help, either. Only

Hi, This is a Centos 5.5 host with one xen guest. About 2 weeks ago, the host randomly lost network connection. By this I mean I could not connect to the services on it, or ping it. Also was the status of the guest. From serial console, I connected to the host, trying to see what happened. No clue (any error messages) in messages or dmesg. ifdown/ifup the interface did not help, either. Only

> First off, I assume you can ping your link-local address: > > ping6 -I eth1 fe80::a00:27ff:fe03:5b8a > > Second, you never mentioned how eth1 was assigned its IPv6 address. > Given that you've tried to embed an IPv4 address within an IPv6 address > (which is normally done with a 0:0:0:0:0: prefix), I'd guess you did it > manually. If so, with what tools?

Hello! Why Debian repo is so strange? Path to a repo should not contain version and subversion numbers. Now you can't receive and even check updates automatically. It's very-very simple to create correct repo. You can even add to it all versions of packages, if it is important. And where is i386 builds? Could anybody create a correct Debian repo for gluster from existing one?

Hi all: I installed xen-3.0.4 on Fedora 7, and installed Fedora 6 as DomainU, but, the network can not work normally. It only work for seconds, then I lose connect. If I ifdown the NIC and ifup it, the network can work for a few seconds, Can anybody help me figure what''s the problem ?? Thank you in advance _______________________________________________ Xen-devel mailing list

Dear All, According to http://wiki.libvirt.org/page/Networking#Debian.2FUbuntu_Bridging May be I have to do "ifdown eth0" How can I define, edit or other task live? ---mohsen

Dear Friends I have 2 netcards (eth0 to Internet and eth1 to internal network) in CENTOS 4.2, bit when I boot system the up eth0 and et1i [OK]. When I run ifconfig the eth1 has not IP configure, then I run command ifdown eth1 and ifup eth1, after eth1 is work perfect. Below I show file /etc/sysconfig/network-scripts/ifcfg-eth1 # Please read /usr/share/doc/initscripts-*/sysconfig.txt # for

I am running Xen on Debian wheezy. I switched from routed networking to bridged networking. Now I can''t seem to get eth0 to come up. When the network script tries to bring it up, it gets an error: RTNETLINK answers: File exists Any tips? details below brian root@trout:/etc/xen# egrep -v ''#|^ *$'' xend-config.sxp (network-script network-bridge) (vif-script vif-bridge)