similar to: odd DTMF behavior on dahdi channel during Echo test

Hi, Continuing with the saga of Digium vs MTNL Mumbai, looking for suggestions on handling incoming Caller-ID issues. The card manages to grab a couple of (random) digits of the incoming CID, but they're more or less useless. Is there any way to fix this? Asterisk 1.8.13, Dahdi 2.5.0.1 on Debian Testing (Wheezy), MTNL Mumbai. Digium, Inc. Wildcard AEX410 4-port analog card (PCI-Express)

We are having an issue where DTMF is not being sent out right away and the tone duration is inconsistent. For a test we send a '5', then a second later we send a '9', and then five seconds later we send a '5'. If you look at the logs below you can see the first '5' is played right away, then the '9' comes in and gets queued, but it doesn't start

Upgrading an ancient customer installation... was running 1.4.23.1 (Trixbox) with Zaptel 1.4.12.9 and a Sangoma A102D, which has been running fine for 5+ years. Customer getting anxious about hardware failure, so we built a new box and installed 1.8.24.0, Dahdi 2.7.0.1, and a new Sangoma A104D. The single active span is an RBS T1 B8ZS/ESF/E&M Wink. I tried to move one span over one

Hi Eric, > On 12 avr. 2016, at 17:48, Eric Cooper <ecc at cmu.edu> wrote: > > On Tue, Apr 12, 2016 at 04:36:58PM +0200, Bertrand LUPART - Linkeo.com wrote: >> I just made a asterisk / dahdi fresh install on Debian 8.4, and ended up with the following packages : >> [...] >> However, i can't find any dahdi startup script, neither init.d neither systemd

Now that I have a new card and my echo problems are 'mostly' solved, I have another major issue to deal with. After about an hour or so the card will stop detecting DTMF tones on incoming calls. dahdi_monitor shows the following: [root at asterisk wctdm24xxp]# dahdi_monitor 1 -v Visual Audio Levels. -------------------- Use chan_dahdi.conf file to adjust the gains if needed. ( # =

OK, using zaptel 1.4 and asterisk 1.4 rev 6745, if someone types an asterisk from the other end of a call, I here it forever till the call hangs up. Looks like it starts the vldtmf, but never ends it from the logs. I am using Digium 400P rev I with one fxs and one fxo module. Any way around this one? Thanks. -- Your life is like a penny. You're going to lose it. The question is: How

A previous issue has popped up and once again I'm out of ideas. During the evenings it seems that the TDM channels will spike (dahdi_monitor) and will refuse to listen for audio of any type, this includes DTMF. The only resolution I know of is to stop Asterisk and restart the dahdi service, but that's not a solution. All channels look like this, even the FXS. [root at asterisk Hardware]#

Hello, I have a server running CentOS release 5.2 (Final) - Elastix 1.3-2 and I have a problem when I try to join to a conference room. When I dial the number I hear the operator voice saying "dial the room number and the # key". I push 4# but the other end doesn?t recognize and I get the operator repeating the message. In the full log I get: [Jan 28 16:54:09] DEBUG[7838]

Hi dears, I am from saudi arabia and using asterisk 1.6.2.13,Dahdi-2.3.0 and Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express) . I am facing problem with detecting caller id before first ring.I recorded the dahdi channel using dahdi_monitor command. Where I am able to see and hear caller-id dtmf tones. Pl tell me the procedure to upload recorded file if you needed. Something I want

Hi, I've kind of ported a DTMF text extry method I wrote some time ago for Dialogic. It is now a semi-working Asterisk app. I've still got to clean up some stuff in how Festival is used to read back what is entered, and then I think it should be OK. Would anyone here find this useful? It takes an entered string, and returns it as a variable. It might sound clunky, but for short entry

Hello, I need to convert the dahdi_monitor output to dBm0, so I can measure Echo Return Loss in dB. I've read a formula that calculate S(k) in ITU-T G.168 recommendation, where S(k) is the signal level in dBm0. Can I use this formula to convert it? If yes, what value should I use to the number of samples if I want to convert a single output from dahdi_monitor? -- Thanks in advance, Gustavo

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.0 DAHDI-Tools-v2.9.0 dahdi-linux-complete-2.9.0+2.9.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete - Introduces support for

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.0 DAHDI-Tools-v2.9.0 dahdi-linux-complete-2.9.0+2.9.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete - Introduces support for

I received a recommendation to check out Asterisk, as a platform to host a simple DTMF response system, something like: Setup up VoIP endpoint on Linux/FreeBSD system Answer incoming VoIP phone calls User enters 100#, perl script plays back "foo" User enters 101#, perl script plays back "fum" User enters 102#, perl script looks up something in

I am studying about echo cancellation in asterisk and I want to use the numeric information from dahdi_monitor verbose for my research. Unfortunately, I couldn't find anything about the unit of measurement used in this tool. Which unit is used to measure the signal level? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, on one of our clients asterisk server we have the problem that you hear nothing on external calls. Here are the details abount the system: Asterisk 1.6.0.22 DIGIUM Wildcard B410 quad-BRI card (rev 01) dahdi-linux-complete-2.2.0+2.2.0 I have setup the following test extension: exten => 9216992,1,ANSWER() exten => 9216992,2,WAIT(2) exten =>

Do you think this should be "Bug Reported"? -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Chris Samaritoni Sent: Wednesday, October 06, 2004 3:42 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Asterisk and Festival, getting gethostbynamefailed error

I just installed Festival 1.9.5 and all dependencies. It works properly from the command line, as I can play the contents of a text string or file from the Festival command line through PC speakers. I then added the code to the festival.scm file, as detailed in Method 1 of http://www.voip-info.org/wiki-Asterisk+Festival+installation I did not apply the patch used in Method 2, because I can not

Hello, I'm in the process of trying to get Festival to work with Asterisk. I followed the install process at http://www.voip-info.org/wiki-Asterisk+festival+installation. To get the Festival to compile I had to add the patch described in the comments. Once added, Festival and the Speech tools compiled without error. How ever, when ever I try to call the test extension, I get a busy

hi group , i am working on dahdi_monitor for measuring voice quality , so i want to know that on which data i can tell that this PRI lines are working properly, is there any measurement on basis of that i can make MOS. i am working from last 2-3 days but i only get idea about making .raw file and making .wav file and visulal mode of RX and TX of PRI line. what i want is measurement of voice