similar to: how to restart the USB driver

I am using centos5.3 x86_64 on a gigabyte GA-MA78GM-US2H motherboard. When I insert a USB thumbdrive its detected with dmesg, I mount it and start to copy files. Then I start getting errors: sdd: assuming drive cache: write through sdd: sdd1 sdd2 sd 7:0:0:0: Attached scsi removable disk sdd sd 7:0:0:0: Attached scsi generic sg4 type 0 usb-storage: device scan complete usb 1-5: reset high speed

To continue here with problems on this compaq v2000 laptop, I put kernel source on a USB disk and plugged it into the v2000. NOTHING IS recognized. I tried to manually mount the disk and nothing either... I thought USB was well established.... I thought trying to recompile the kernel for realtek support might get my networking going... I am stuck??? Jerry -------------- next part

Hi all Is there a procedure to use an 8GIG thumbdrive to copy the centos 5.2 dvd contents to the thumbdrive then run isolinux (or something like it) and be able to use the thumbdrive as the install media? Seems like it should work, however my machine only has syslinux not isolinux. yum provides isolinux does not return anything. Anyway I was trying to get to a point where I can just stick a

Hi, What modules are needed in my mkinird command with --preload to boot from usb thumbdrive? THanks, Jerry

Hi I just grabbed an 8gig thumb drive, took disk 1 centos 4 i386, copied the isolinux directory files to my thumbdrive, then ran syslinux -sf /dev/sdc1 on the device plugged it into my laptop and it does not boot. Is there a step(s) I am missing to get a bootable thumbdrive with centos? Thanks, Jerry

I''m currently working on moving storage services into their own domain and I''ve been looking at blktap2. I''ve been trying to get an image mounted with blktap2 and for some odd reason and tapdisk2 keeps hanging instead of quitting at the end. I haven''t removed any of the storage startup code at this point so everything should be as it normally is in xen-unstable.

I have a bootable usb thumbdrive now... three partions, msdos for syslinux booting, ext3 and swap. How can I grab my QEMU installed centos 4 image and put it on the ext3 /dev/sdc2 partition on my thumbdrive? THanks, Jerry

Hi all, I am trying to find information on taking a DVD of centos 5.2 x86_64 and putting it AND my kickstart file on a USB8G thumbdrive. Note - I am not INSTALLING linux on the USB disk just trying to make installation media for it. I am not taking just the bootdisk.img file to make the USB bootable but the entire DVD content on the USB and my kickstart files. I'd like to just be able to

What subsystem replaces /sbin/hotplug in CentOS 5? The older hotplug package is missing from CentOS 5 and /proc/sys/kernel/hotplug yields an empty string. Since hotpluging for standard devices still seems to work, I presume that something replaces the hotplug helper found on CentOS 4. Can someone point me in the right place? All of my Googleing points me back to the (obsolete?) /sbin/hotplug

Is there anything new on installing centos 5.1 on a 4G thumbdrive? What about the number of writes to the flash? Is that still a problem? Jerry

I move my notebook around my office. Sometimes I am using the internal pointers, sometimes a USB mouse, and sometimes a USB keyboard/mouse adapter that is plugged into a kvm (actually two of them). With one of these USB k/m adapters, when I plug in, the system fails to recognize the mouse (but no problem with the keyboard). The 2 adapters are the same brand/model (Aten), but the KVMs are

Hello I am using a Junghanns QuadBRI ISDN card - the module name is qozap. If I like at my interrupt assignment, qozap is sharing interrupt 10 with libata and uhci_hcd. I think libata is the IDE hard drive module and uhci_hcd is a USB module. linux:~ # modprobe qozap linux:~ # cat /proc/interrupts CPU0 0: 12634579 XT-PIC timer 1: 10 XT-PIC i8042

Hi, I have an IBM xSeries server... and the digium card is sharing IRQ with USB and giving me crackling audio. >>> cat /proc/interrupts >>> >>> It brings up these results: >>> 0: 10566547 IO-APIC-edge timer >>> 1: 9 IO-APIC-edge i8042 >>> 2: 0 XT-PIC cascade >>> 8: 1

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

I am having the darnedest of times trying to get my WinPE to work off the syslinux loader. I used to use isolinux, and my isolinux config would just invoke the etfsboot.com file which i had renamed to loader.bin, and everything would work just fine off a cd. But now I'm trying to transfer all of my cd functionality to thumbdrives. With Syslinux, i have my syslinux.cfg file calling loader.bin

Hi all, I am using a TDM400P card with 2 FXS and 2 FXO modules. Everything seems nice, but i'm not able to make calls nor to receive any. When I try to make a call, I keep receiven the "all circuits are busy now" message, and when I receive calls, asterisk doesn't seems to care (don't get anything on the CLI) I'm using Asterisk 1.2.17 and Zaptel 1.2.16 from Xorcom's

My thumbdrive w/Syslinux and memdisk doesn't work on my Thinkpad laptop. But the thumbdrive does work on desktop platforms. And .. if i use Grub4dos with Syslinux .. it works on the Thinkpad Laptop. Any assistance would be greately appreciated! Thanks! <<john>> ____________________________________________________________________________________ Access over 1 million songs

Are there instructions on how to take the actual ISO install image (not a live image), put that iso file on a USB thumbdrive and install from that instead of DVD? I would be interested in putting a kickstart file on the USB also. so just plug in a USB and everything installs just the way I want/need. Thanks, Jerry