similar to: Megraid SAS virtual disc question

hi all We have a rh linux server connected to two HP SAN controllers, one an HSV200 (on the way out), the other an HSV400 (on the way in). (Via a Qlogic HBA). /etc/multipath.conf contains this : device { vendor "(COMPAQ|HP)" product "HSV1[01]1|HSV2[01]0|HSV300|HSV4[05]0" getuid_callout "/sbin/scsi_id -g -u -s /block/%n"

I have Centos 5.2 and am trying to set up my first tape loader, a Quantum SuperLoader 3. My "cat /proc/scsi/scsi" outputs the following: Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: transtec Model: PV610F16R1C Rev: 373I Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: HP Model: Ultrium

Basically the issue comes down to my Volume Groups not being found by this initrd, causing good ole kernel panic. initrd-2.6.12.6-xen3_12.1_rhel4.1.img [root@xen01 lvm]# uname -a Linux xen01.inside.***.com 2.6.9-22.0.2.ELsmp #1 SMP Thu Jan 5 17:13:01 EST 2006 i686 i686 i386 GNU/Linux [root@xen01 lvm]# cat /etc/redhat-release Red Hat Enterprise Linux ES release 4 (Nahant Update 2) Everything

I'm having speed problems with the SCSI card we're using to do tape backup. It seems to be functioning in 16 bit mode and the current thinking is that perhaps it's using a legacy driver instead of the correct one. The Adaptec site has a 'driver' for RHEL5 which I've downloaded and tried to install but it seems to have a problem installing on a CentOS-5 system. [root at

Hi people, I installed a via SATA controller in a CentOS release 3.8 (Final) - I needed additional disk space. After the first boot, the kudzu service, added the following line to /etc/modules.conf: alias scsi_hostadapter sata_via and I rebooted. After reboot in dmesg one can see: scsi0 : sata_via scsi1 : sata_via Vendor: ATA Model: SAMSUNG HD080HJ Rev: WT10 Type: Direct-Access

Hi, I'm attempting to add virtual SCSI disks to my KVM guests the same way as I did with VMWare, but I'm having issues. Without knowing any better, I'm assuming it has something to do with me attaching the disk incorrectly, and when I'm looking at the VMWare config one thing I noticed was the SCSI mode "independent-persistent" which I cannot find in libvirt

OK - I only have one tape drive but a real problem these days backing up. I ***may*** have connected the SCSI connector to the 'other' external connector when shifting stuff around in the rack. # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: MegaRAID Model: LD 0 RAID5 69G Rev: 4.10 Type: Direct-Access ANSI SCSI revision: 02

I have an IDE based PC running Linux/CentOS4 to which I wish to attach a scsi dlt. The host controller is an Adaptec AHA3940 something that lspci reports as: SCSI storage controller: Initio Corporation 360P (rev 02). I would like to have the system load the driver for this adapter at boot but I have two problems: 1. I am not sure which driver to use; and 2. I do not know how to force

Hi, all! I want to change current RHEL 4.0 ES into CentOS 4.2 on Sun X4100 server. The server has SAS SCSI based two 2.5" hard disks. I could only install RHEL 4.0 Update 1 because the server is equipped with RHEL 4.0 Update 1's device driver only. I've included below the boot process messages concerned with SCSI controller. If it's possible for me to install CentOS 4.0 on my

Everyone, about 4 years ago, I tried to install CentOS 6 on a Supermicro server with SCSI drives using a LSI raid system. I could never figure out or find a way to make the installation disc of Centos 6 identify the SCSI drives. The installation disc for Centos 5 identified the SCSI drives without a problem. I finally gave up on Centos 6 and installed Centos 5 and the system has worked very

I am currently testing an Overland Tape storage unit with a LTO-3 drive on CentOS 4.4. After a random amount of time but usually when we have backed up about 0.5-1TB we get scsi errors which cause the backup to fail. I have rebuilt the box with Solaris 10 x86 and Windoze to prove the hardware and have successfully backed up over 3TB on each OS without error. Can anyone offer advice on how to find

----- Original Message ----- From: Karl Heyes <karl@pts.tele2.co.uk> To: <icecast@xiph.org> Sent: Friday, January 31, 2003 5:29 PM Subject: Re: [icecast] Re: Compiling ices <p>> On Fri, 2003-01-31 at 06:39, Marc Remijn wrote: > ... > > > Kernel output: > > > > invalid operand: 0000 > > CPU: 0 > > EIP: 0010:[<d08e25b1>]

Hello, I have recompiled a Linux 2.4.18 kernel on my Sparc and I receive some oops when quick disk access are performed. For example : I download some files on a local server with ncftp (-TR directory), and ncftp hangs up (with kernel oops !). I cannot umount the device and I must reboot the station. For information, my sparc is a SparcStation 5 (85 MHz) with 160 Mbytes and 3 SCSI

https://bugzilla.redhat.com/show_bug.cgi?id=1441197

I recently came across an enormous cluster of x86 clone machines running fedora core 1 (2.4.24) which have typically all intel or amd have VIA IDE chipsets. They frequently experience corrupted journals rendering the ext3 partition in read-only mode. More important than recovering the filesystem, I am interested in finding the root of the problem. The common hardware that all of these

I increased the SAN partition size for a given volume. Is there a way I can have fdisk recognize the new size without a reboot? Thanks, Scott

I ran some iperf tests today and it looks like the etherbridge is the limiting factor on throughput. In the beforetime, I saw great throughput to the VMs; over 800 Mbps. With the bridge, the numbers are in the 400s somewhere. Is this the speed I can expect from the bridge? Is there some tuning I should try, or another way to get more bandwidth into the VMs? This is with xen-2.0, 2.4.27-xen0

Is there a command that will list the disks that the system currently has? The df and mount commands only display info about filesystems. Charles L. Sliger, Information Systems Engineer, chaz at bctonline.com "No matter where you go, there you are..." -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All, I have a Quantum scalar i40 tape library. I need to configure it to TWO tape partition libraries, e.g., library_a and library_b, so that each library has its own tape drive. Then connect this physical tape library to two different CentOS servers so that each server can see its own media changer and tape drive. I once had a successful configuration on one host but NOT on the other. One

When I try to burn anything to cd, I get a message to insert a CD large enough for my file (normally an ISO image). Doesn't matter if the iso image is a 600Mb Centos ISO or a 48Mb DSL ISO. Same warning. My CD-Rs are Memorex 700MB/80min 52x disks that work just fine on XP systems. So what am I missing configuration-wise?