similar to: parameter of htb

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

I am using the script below to simulate a very low bandwidth connection. I found that I could turn the bandwidth knob down to about 4kbit, but below that I didn''t get any traffic through. I''ve had a look at this generally, but couldn''t find an answer. It doesn''t even seem like the first reply packet gets through. I have tried it with much bigger buffers,

Dear all, I want to make a filter for all IRC-Dalnet traffic, so I want to put all traffic for port 6660, 6661, 6662, 6663, 6664, 6665, 6666, 6667, 6668, 6669, 7000, 7001, 7002, and 8000 to a class. So, I create a TC script as below. I''m sure, it is not effective, and we can write it in simpler. I need help, how to make my script below are simpler. The simpler, the better. Thank you

I''d like to implement something like SFQ, but with a cap of a rate per flow. Essentially, I''d like to be able to limit citrix connections to 30KBps without having an overall traffic flow cap for all citrix connections. Slightly preferable to this would be something that would actually work per flow instead of the stochastic algorithm. Is this possible? Thanks, Bill --

The script is corect ? #!/bin/bash /sbin/iptables -F -t mangle /sbin/iptables -X /sbin/iptables -t mangle -N mark_horiz_src /sbin/iptables -t mangle -N mark_horiz_dst /sbin/iptables -t mangle -A PREROUTING -i eth0 -j mark_horiz_src /sbin/iptables -t mangle -A PREROUTING -i eth1 -j mark_horiz_dst /sbin/iptables -t mangle -A OUTPUT -o eth0 -j mark_horiz_dst /usr/local/bin/mipclasses -s

Howdy all, I posted this message to the netfilter mailing-list and didn''t get much response. I apologize if anyone here is getting this for a second time. Anyway, I recently migrated my firewall from a FreeBSD box running ipfilter, ipnat and dummynet to a Gentoo Linux box running netfilter and tc. I have to admit that I''m having problems visualizing tc in my head. So, I was

htb was used to control traffic stuctrul is like that(default is 1:20): |----1:100 |------1:10| 1:1| |____1:110 | |------1:20 #AC="tc filter add dev eth0 protocol ip parent 1:0 prio 1" #$AC u32 match u32 0xac100b00 ffffff00 at 16 flowid 1:10 #$AC u32 match u32 0xac100b01 ffffffff at 16 flowid 1:100 I copy a file to 172.16.11.1 class 1:100 go into

Hi I''m moving to hfcs (mostly succesfuly:) ), but I''ve encountered a strange problem: When I download something from this server using wget (one thread) via an idle uplink, I get no more than 130 kbit/s, and when I''m using prozilla (or start more wgets), I get about 200 kbit, but still it''s not all the link can do (240) - the rest remamins unused. Is this

Hello mailing list, i stand bevor a mystery and cannot explain it J. I want to do shaping and prioritization and I have done these following configurations and simulations. I can´t explain, that the combination of PRIO and TBF is much better than the HTB (with the prio parameter) alone or in combination with the SFQ. Here are my example configurations: 2 Traffic Classes http (80 = 0x50) and

Hi there, I have a Debian sarge 512 MB RAM machine with icecast2 and ices2 that I installed via aptitude. I have a 3MBit/s download and 800KBit/s upload link. I would like to configure icecast2 and ices2 properly. Here is my situation: 1)I have a dtdns address omac.darktech.org 2)icecast2 and ices2 on port 8000 would be fine. 3)I simply want to broadcast my 6 year old niece's voice which

Hi, I?m fighting with a silly problem: my syslog tells me tinc cannot route a packet. I can use a telnet or the good ol ping, it is the same effect. When I?m pinging from the laptop (172.16.11.2) the network address (172.16.11.0) or any address numerically lower than the laptops address, the packet gets routed, otherwise not. And when I ping the network address, I get the reply twice, as to be

Hello, I have problems setting up HTB. This is my setup : NET 1024/256 ADSL || eth1 Linux Firewall eth0 || LAN 10.a.a.a I want to GUARANTEE for an IP (10.x.y.z) a 800kbit bandwidth for HTTP download. But When 10.x.y.z does no HTTP download, other trafic must get the whole bandwidth, of course. The script I use (see below) is quite the same as presented at (the greeeeat page) :

hello, I have working htb system with about 1000 users. Until now I reload all rules at change, but it take too much time to apply. I cannot delete applyed filters. There is rules for one user: #!/bin/bash -v # Download shaper EX -> 2:20 /sbin/tc class add dev eth2 parent 2:20 classid 2:1775 htb rate 8000Kbit ceil 10000Kbit quantum 1514 /sbin/tc qdisc add dev eth2 parent 2:1775 sfq perturb

About the cbq.init. Four machines which traffic to limit in same LAN. Is the samething if I put limiting rules to four different files or all to the same file? Like: DEVICE=eth0,10Mbit,1Mbit RATE=64Kbit WEIGHT=6Kbit PRIO=5 RULE=192.168.0.5 RULE=192.168.0.6 RULE=192.168.0.7 RULE=192.168.0.8 OR four equal files with different IPs, Ids and no PARENT rule? What style of ID numbering you use if

Hello, I''m trying to get lossless VoIP traffic over my 3000k/500k ADSL line. Shaping outgoing traffic is no problem: I set total ceil for outgiong device (ppp0) to 450kbit and put VoIP into highest prio class. Even during full upload the voice is clean on the other end. Now I tried to get the same result for incoming data. I attached HTB to eth1 where the incoming voip traffic is

Hi, this is my Linux Box ---------------------------- LAN 1 -----|--eth1 <---br1--->eth0.1 | | \ | | eth0--|----- 802.1q tagged 1 Mbps link | / | LAN 2 -----|--eth2 <---br2--->eth0.2 | ---------------------------- I have to bridge the 2 lans

Hello everybody, I have a Linux router with an ethernet adapter and a ADSL device. My router has a GRE tunnel connected to a remote IP address. Using "tc" I have configured 3 different classes: 1. 290kbit rate (used for Voip Services) 2. 180kbit rate (used for GRE tunnel) 3. 80kbit rate (for generic data traffic) For each class, using "iperf", I send some data from a PC

Hi all, I recently installed traffic shaping on my ADSL line with a nominal upload rate of 1MBit. My Modem says it has an upload bitrate of 843 kbits. So I thought, to use a ceiling of 800kbit for the root qdisc is a good idea. But with that setting I only achieved upload rates of around 300kbits whereas I reached around 650 kbits without traffic shaping. Yesterday I played a little with the

Hi there, I am experiencing some issue with X-Lite. When I am calling over the phone thru my PSTN-to-VoIP gateway internationally using G.729 the quality is just perfect. When I am using X-Lite to connect the same box, and then to call internationally - I am experiencing some issues. I have 5Mbit/800Kbit cable link with average 60 msecs to my VoIP box. The transfer rate is never falling below

Hello to everybody, We have an ADSL link with uplink speed of 530kbit, the goal is to divide the traffic into three classes, let say A, B and C. A data rate of 240kbps must be guaratee to class A. The remaing rate must be assigned: at least 180kbit to class B and at least 80kbit to class C. The unused band of class A must be given to class B and C (if needed) The unused band of class B must be