similar to: how to clean "tc" configure

Hi, I want to see bandwidth every ip address in the local network that passing my linux gateway in the console, may be it''s similar like mrtg (web based version) It''s possible ? Best regards, >--<Kristiadi Himawan>--<

ingress can be used to control the incoming packet, such as: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: protocol ip prio 5 u32 match ip src 172.16.1.11 police rate 10kbit burst 10k drop flowid :1 tc filter add dev eth0 parent ffff: protocol ip prio 5 u32 match ip src 172.16.1.22 police rate 10kbit burst 10k drop flowid :2 first ,I do not sure these method can

Hi! I answer to two messages from this thread (I use digest). lartc-request@mailman.ds9a.nl wrote: > > Message: 3 > Date: Fri, 16 Jul 2004 10:51:37 -0700 (PDT) > From: ibro tj <ibb_linux@yahoo.com> > Subject: Re: [LARTC] QoS for Voip. > To: lartc@mailman.ds9a.nl, alessandro.ren@opservices.com.br > > Hi, > > the hint from Martin A Brown which I am

Hi All, concerning the problem when running the "ip ru ls" command. I faced with the same problem, and I solved it by making sure to include the following settings into the kernel configuration (2.4.18): CONFIG_IP_ADVANCED_ROUTER=y <=== CONFIG_IP_MULTIPLE_TABLES=y <=== CONFIG_IP_ROUTE_FWMARK=y CONFIG_IP_ROUTE_NAT=y CONFIG_IP_ROUTE_MULTIPATH=y CONFIG_IP_ROUTE_TOS=y

''imq-2.4.18.diff-9'' patched to kernel18 and ''iptables-1.2.6a-imq.diff-3'' patched to iptables-1.2.6a the following options are choosed: Networking options ---> IP: Netfilter Configuration --->IMQ target support (as a module) Networking options ---> IPv6: Netfilter Configuration --->IMQ target support Network device support --->IMQ

Hi Is there a way of marking packets by mac address instead of ip or ports using a "tc filter u32 match"? I read somewhere that I could use the offset -8 and -14 to grab the mac addresses but if I use anything lower than -8, for example -9, I get an error. I''m modifying the wondershaper script to cap the download speed by mac address. Any sugestions?

Hi everybody! I''ve been trying with htb and tc filter. It seemed to work fine, but after testing with ethloop I''ve realized that traffic is not being distributed through the leaves as I thought. When sending packets to 1:10 and 1:11 at the same time, there''s no bandwidth sharing. There''s no traffic through 1:11 until traffic through 1:10 has finished. Though

I''m trying to implement something similar the the diagram in section 9.5.2.1 in the LARTC HOWTO, but must have missed something somewhere :( I''m trying to hack up wondershaper, as it looked like a good place to start.. Here''s where I currently at, but I''ve tried alot of different things, all failing, some worse than others. The end result is to throttle back 126

For simplicity, I tried this: tc qdisc add dev eth0 root handle 1: prio tc qdisc add dev eth0 parent 1:1 handle 10: sfq perturb 10 tc qdisc add dev eth0 parent 1:2 handle 20: sfq perturb 10 tc qdisc add dev eth0 parent 1:3 handle 30: sfq perturb 10 tc filter add dev eth0 protocol ip parent 1: prio 2 flowid 1:1 The last line prints: Unknown filter "flowid", hence option "1:1"

Hi, I have some interesting problem with htb , I set up root class and sub-classess: $TC qdisc add dev eth0 root handle 1: htb $TC class add dev eth0 parent 1: classid 1:1 htb rate 1990kbit ceil 2000kbit $TC class add dev eth0 parent 1:1 classid 1:10 htb rate 190kbit ceil 200kbit $TC class add dev eth0 parent 1:1 classid 1:11 htb rate 1400kbit ceil 1600kbit $TC class add dev eth0 parent 1:1

Hi, I have a problem with ''tc filter'' on a 2.4.22 kernel from Slackware 9.1 distribution. The tc command binary is from htb3.6-020525.tgz (http://luxik.cdi.cz/~devik/qos/htb) I''m trying the following command sequence: tc qdisc add dev eth0 root handle 1: htb default 1 r2q 1 tc class add dev eth0 parent 1: classid 1:1 htb rate 1200kbit ceil 1200kbit tc class add dev

Will stephen's defrag run in a ext3 partion correctly? What about the performance? _________________________________________________________ Do You Yahoo!? 摊开你的掌心 让我看看你 http://sweepstakes.yahoo.com/2002cnuser

Dear all, Where can I find any document on extended filesystem version 1? thanks. _________________________________________________________ Do You Yahoo!? 摊开你的掌心 让我看看你 http://sweepstakes.yahoo.com/2002cnuser

I''m using htb classes on my firewall to queue traffic and implement different restrictions on different protocols. tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1: htb default 190 tc class add dev eth0 parent 1: classid 1:3 htb rate 2mbit burst 30k tc class add dev eth0 parent 1:1 classid 1:90 htb rate 50kbit ceil 384kbit burst 5k tc qdisc add dev eth0 parent 1:90 handle

Hi, I want work out a GUI interface for htb and now here comes to the part about adding and removing classes and filters. Here is an example script. TC="tc" DEV="dev eth1" echo "Add root qdisc, default traffic go to 1:30" $TC qdisc add $DEV root handle 1: htb default 30 echo "Divide the traffic into different classes and levels" # -------- level 1

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

Hi, One more of those ... 1) what is a ctoken with regard to HTB? Does the ''c'' stand for ceil and if so how is it different from tokens? 2) Is the difference, only in the generation of these tokens? 3) Would the ctokens and token be treated equally once borrowed? Kindly help. Thank you. Regards, suraj. __________________________________ Do you Yahoo!? Protect your

Hi All, I''m using iptables-1.2.7a on RedHat8 kernel 2.4.20. I wanted to limit the file-sharing traffic to the internet. I marked the packets with iptables: iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1024:1862 -j MARK --set-mark 1 iptables -A FORWARD -t mangle -p tcp -s 192.168.1.1/24 -d ! 192.168.1.1/24 --dport 1864:65535 -j MARK --set-mark 1

Hi! I really need help with a u32 filter that won''t match what I think I''m telling it to. The situation is that I have set up an internal computer to change the TOS value of packets sent by certain processes to 0x1E (If anyone known of a better way to mark packets, please tell me. I would love to find some module that adds an IP option with UIDs and GIDs to the packets - does

I posted earlier when I noticed that htb was releasing packets in pairs, even though my burst/quantums were 1 pkt. To fix I set HTB_HYSTERESIS 0 in net/sched/sch_htb.c . This gives a noticable gain in upstream worst case latency, for me with 256kbit/s up I used to see +90 sometimes, now it''s +45. For the many who have 128 up it should limit them to +90 rather than +180. Andy.