similar to: Iptables, SNAT/MASQ, Multiple gateways

Hi, my company have just bought new network and I have question about one problem. As in topic we must use few completely different dsl''s and balance traffic between them. 2M/0,5M 4Mb/0,5M 8M/0,5M M=Mb/s I''ve never done such thing before so I have doubts how it will work. If the links are symmetric 2/2 4/4 8/8 there is no problem because with weights I can compensate the

Hello, Since I could not figure out my previous problem, let me ask in a different way. I have 3 networks inside my LAN. They are 172.16.55.0/24 , 172.16.56.0/24 and 172.16.57.0/24 respectively. They all use eth0 as an alias. I also have 2 uplinks to different ISPs. One of them is leased line and the other one is ADSL. One of my uplink is 81.8.120.18/30 with gateway 81.8.120.17 on eth1 and the

Maybe a strange request, I''ll try to explain this as clearer as I can (forgive my bad english, please :-) ). I''m setting a linux box as a router. My router uses multiple routing tables, so I can address the traffic from specific ip addresses of my lan to distinct ISPs providers (specifying a different default gateway fo r each table), marking packets with iptables

Hi all Does anyone know if i can use ethernet aliases like eth0:1 in advanced routing like multipath routing in order to avoid to have nxEthernet interfaces in my Linux box. Thansk in advanced -- Guillermo Gomez <ggomez@neotechgw.net> neotech _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

Folks, Ive got two ISP connections that I am using with: --- ip route add 192.168.200.0/24 dev eth2 src 192.168.200.11 table connection1 ip route add default via 192.168.200.1 table connection1 ip route add x.175.244.0/24 dev eth1 src x.175.244.2 table connection2 ip route add default via x.175.244.1 table connection2 ip rule add from 192.168.200.11 table connection1 ip rule add from x.175.244.2

Hello, I have finished setting up the load balancer with IPROUTE ... also patch the kernel to support DGD and now it''s working fine with the valuable guide at LARTC website, Julian Anastasov, and the kind people in this mailing list. Now I would like to launch a web server and a ftp server to the public but I''m stuck into a problem and really need your help. Currently internal

I am developing load balancing router, But I have a question about fail over. The follow diagram is my test environment and scripts. ------------------------------------------------------------------- Environment Setting PC1(192.168.10.2) | (LAN) | PC2-eth2(192.168.10.1) +

Hello everybody. I''m running linux 2.6.19 with nth match to alternatively snat outgoing connections to two different ip addresses for load balancing between two adsl lines: Here is: $IPTABLES -t nat -A POSTROUTING -s my_ip --protocol tcp -m multiport --dports 80,443 -m statistic --mode nth --every 2 -j SNAT --to adslA $IPTABLES -t nat -A POSTROUTING -s my_ip --protocol tcp -m multiport

Hi, I have a client connected to the ''net through 3 ISP''s. Have set up a Linux box to do routing and load sharing for the 3 connections. A fourth interface is connected to the LAN with private IP addresses. Am using iptables to SNAT traffic to the appropriate IP depending on the interface the packet gets routed onto. The setup looks something like this: Interface IP

Ok ive been trying to get this to work for about half a year now. Ive searched all over the internet for a solution for my problem. Ive found some solutions, but they only led me to yet more problems. What we want to do is the following: I live in a student complex with 7 other people. Every room has its own internet connection from the same ISP. Ip, gateway, subnet are asigned through dhcp on

Hi Ppl I have 5 adsl lines that after reading quite a bit i managed to get load balanced now abvoiusly it doesnt load balance evenly and this works on what routes are still in the routing cache. my question is my outbound masquerading had to be modified to use snat in iptables instead of just plain masquerading my outbound masquerading now works but my inbound port forwarding doesnt work would

Hi all, I have a similar question like many asked before I know but Please help as i cant figure out where the problem is and how should I tackle. I have 2 ISP connections. I want to share the bandwidth from both. I have copied the script from many places and created my own after changes. Problem is that only one connection is utilized at a time. Not both working. ratio of consuming

how to use iproute/iptables to balance by packet OUTBOUND traffic between 2 PPP (pptp cable modem and pppoe adsl modem) links to the same ISP . also by using the fact that the ISP dosen''t filter source IP address - meaning i can use either PPP''s link assigned IP address as the source IP in the ip header.., it works for both devices.., what i want to achive is : when uploading a

Hi, I am connected to two DSL providers (DSL 1 - 1Mbps downlink/384kbps uplink and DSL 2 - 2Mbps downlink/512kpbs uplink) I would like to only allow ftp, pop3 and http via the DSL 1 and only smtp, ipsec and pptp via DSL 2. How can I do so? Can I use iproute to route these protocols? Below is my ip routing: - # DSL 1 ip route add 2.2.2.208/30 dev eth0 src 2.2.2.210 table 1 ip route add

Hi all iam trying to deploy loadbalance and failover My setup description --Fedora Core 4 --Linux 2.6.12.3 #1 SMP Mon Jul 25 22:37:34 IST 2005 i686 i686 i386 GNU/Linux --tc utility, iproute2-ss050314 --ip utility, iproute2-ss050314 --iptables v1.3.0 And i had deployed Following configuration #table main with priority 50, the highest one ip rule add prio 50 table main #table 201 ip rule add

hi, in the masq file''s documentation, there is a sentence: "If you have a static IP on that interface, listing it here makes processing of output packets a little less expensive for the firewall." this realy means that SNAT to the primary address is less expensive than a MASQ rules in the netfilter? is this documented anywhere in iptables/netfilter? thanks. -- Levente

Sorry for the long descritpion of the problem, I''d like to know If I misunderstand something or if I meet an intrinsic limit of my setup. 217.58.51.162 HDSL eth1 - SRV_XP: 192.168.254.10 eth0: 192.168.254.1 -----+------------------+------- 81.121.243.250 ADSL eth3 - I want to allow incoming pptp request (port 1723) to be forwarded to srv_xp

hello, my name is Denny. I am new in this list. I am trying use multiple uplinks as describe in the lartc documentation (http://lartc.org/howto/lartc.rpdb.multiple-links.html) with squid transparent proxy in my gateway server. let me draw the configuration : /----------------- -----DSL1-----| \ |Transparent proxy |----Local network -----DSL2-----|

snat not working my local ip is aaa.aaa.aaa.aaa asterisk sitting on the internet at ip bbb.bbb.bbb.bbb my firewall''s internal ip is 192.168.0.254 i did snat: iptables -t nat -A POSTROUTING -o ppp0 -j SNAT --to aaa.aaa.aaa iptables -t nat -L -v gives: Chain POSTROUTING (policy ACCEPT 23663 packets, 2182K bytes) pkts bytes target prot opt in out source destination 33056

Hi There, I am also trying to do the same for my network. I have two links from different ISPs and I want to configure a failover and load balancing Linux router. I am facing same problem here, that how to detect link failure and let Linux box switch the gateway. I know it works when the first gateway is physically down and not reachable. But what to do if my link is up but there is problem