similar to: RE: 4 nic advanced routing question update

Hi, I have a simple question (well, at least I think it''s simple!). I have a router, with four Ethernet cards; eth0-eth3. eth0 and eth3 are the ''external'' cards, connecting to my ISPs. eth1 and eth2 are connected to my internal networks. What I want to do is basically filter all the traffic from one card to another, in this configuration: eth1 to eth3 eth2 to eth0

Hi all, I have a similar question like many asked before I know but Please help as i cant figure out where the problem is and how should I tackle. I have 2 ISP connections. I want to share the bandwidth from both. I have copied the script from many places and created my own after changes. Problem is that only one connection is utilized at a time. Not both working. ratio of consuming

Hello,I have single linux router ( fedora core 1 ), 2 ISP, 1 internal network,1 IP space from every ISP My scenario: eth0 1.0.0.2 netmask 255.255.255.252 -> ISP 1 eth1 2.0.0.2 netmask 255.255.255.252 -> ISP 2 eth2 1.0.1.1 netmask 255.255.255.0 -> IP space from ISP1 eth3 2.0.1.1 netmask 255.255.255.0 -> IP space from ISP2 Config I try: /etc/iproute2/rt_tables: 10 isp1 20 isp2 ip

I am working on a split route and ShoreWall system. I reviewed the lartc documentation but have a few areas that I still need help on. Here is my network: 64.xxx.xxx.1/25 66.xxx.xxx.129/26 | | ################################################# # Eth2 64.xxx.xxx.2 eth0 66.xxx.xxx.130 # #

Hi all, i''m puzzled by a ploblem and I don''t know how to debug it... I have a firewall with 2 gateways, adsl and isdn. Main gateway is via adsl, backup via isdn. I setup 2 table ''adsl'' and ''isdn''. You can find a description below. I made a script to test both tables. That mainly 1. adds an iptables -t mangle -A

I have a computer with two interfaces, say with addresses 192.168.1.1 and 192.168.1.2. I want to set up routing such that when I ping 192.168.1.1 it goes out through 192.168.1.2 and not to the local interface. Is this possible - all my attempts so far have been unsuccessful? If so, pointers, etc. would be gratefully appreciated. Jim -- Jim Redman (505) 662 5156 x85

Sorry for the long descritpion of the problem, I''d like to know If I misunderstand something or if I meet an intrinsic limit of my setup. 217.58.51.162 HDSL eth1 - SRV_XP: 192.168.254.10 eth0: 192.168.254.1 -----+------------------+------- 81.121.243.250 ADSL eth3 - I want to allow incoming pptp request (port 1723) to be forwarded to srv_xp

Hello everyone, Please excuse these basic questions but I am new to Linux and I am getting desperate for answers. We are running redhat linux and after many hours of investigation I am unable to get a certain ip rule and ip route command combination to work. These are the software versions installed. [root@c1b04a01 linux-2.4.21-15.EL]# uname -a Linux c1b04a01 2.4.21-15.ELsmp #1 SMP Thu Apr

Hi! I got some strange problem with routing loadbalancing. I cannot get the full speed from my ISPs until I get some big files from close ftp server. I have server with one connection to internal network and 3 to ISPs: __________ | eth1|---- ISP1 | | internal--|eth0 eth2|---- ISP2 net | | (~300 | eth3|---- ISP3 hosts

I am running a public core router using private links from my provider. Details: RH7.3 9 interfaces (all Intel) eth0 is default gateway and has a private IP address all other interfaces are links to other routers or networks eth3 has a public IP address The core router will rarely need to access sites out on the internet, but when it does it cannot get there because the eth0 has a private IP

Hi all, I''m trying to set up a computer with 2 routes to the internet, much as described at http://lartc.org/howto/lartc.rpdb.multiple-links.html .One of my interfaces (eth5, 192.168.2.2) is only used for traffic originating inside the network. The other (eth1, 192.168.1.2) is only used for a VPN, where all (udp) traffic originates from outside our network. I have created a second

Hi all, I have a debian server with 4 network cards: The first card is used to connect to public network and this network connects with a big router. The Second, third and fourth cards are used by other networks. The first card used a dinamic route with the big router. The other cards used a static route with a little router. All runs good but my problem is when I try to use the IP of my first

After many many hours of frustration and failures I''m almost to the point that I don''t think this is even currently possible with Linux. With out going in to too much detail, I am effectively wanting to do the following. I want to be able to take traffic in from a local LAN on eth0 and route it out eth1 to a default gateway with a static IP. I want said default gateway

I''ve made some tests... eth2 is my internal interface, LAN is connected here. Before I had IMQ device in AB mode... PREROUTING [A]fter NAT, POSTROUTING [B]efore NAT. I want the same situation on ifb. I do this in this way: --- # incoming traffic here from LAN is before NAT tc qdisc add dev eth2 handle ffff: ingress # outcoming traffic here from WAN is after NAT tc qdisc add dev eth2

I already setup several 2 gateways boxes, with rules too decide which lan should use which gateway. Now I''m stuck with a simpler problem. At home I was just making some experimental setup: * 1 adsl (ppp0) * 1 more tables in rt_tables (200 ping) called "bluff" * table ''bluff *has not* a default route root@fw-eden root # ip ro li table bluff

Hi, Apologies for the cross-posting; I''m not sure whether this is a firewall or routing issue, or both! I have four network cards, detailed below. eth0 and eth3 connect to my ISPs, and eth1 and eth2 connect to local networks. I want to route all traffic from eth2 to eth0, and from eth1 to eth3. However, I am having a few problems with this. eth0 ip: 192.168.100.253/24 gw:

Can I add routes to rt_tables by hand with the vi editor? If I add a route to that file, it will be there if I reboot the box? I am sure there are stupid questions but I can''t find the answer into the papers I have here. Luis Miguel Cruz Miranda. CCNA - Systems Administrator _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl

Hi, I have a little problem to setup iproute in my network It looks like this: ---- ----- ------ R1 R2 R3 ---- ----- ------ | | | | | | ------------------------------- ETH1 ETH2 ETH3 ETH0 ETH4 -------------> DMZ ------------------------------ | |

hello list (and martin) ;x i have now composed my final(?) policy routing design. the goals i had when beginning with this, for you that have not follow mine and martins thread, was to 1) only let 192.168.1/24 to see all routes, 2) not route between defined networks, except to and from 192.168.1/24 and 3) not defined networks should only be able to reach 192.168.1/24. this might sound simple.

I have a server with 4 nics. Two are using different internet connections, both with static IP's, and two are connected to our private network. The two internet facing nics seem to be battling over the gateway designation. Which ever I designate as the gateway the other stops responding to incoming traffic. I need both to listen to inbound traffic. One for our main web page and the other