similar to: HTB shares equally when borrowing enabled :(

Ok, shaping on Linux is new to me.. so bear with me if i am just stupid. curtain:/etc/shorewall# grep TC shorewall.conf | grep -v ^# TCP_FLAGS_LOG_LEVEL=info TC_ENABLED=Yes CLEAR_TC=Yes TCP_FLAGS_DISPOSITION=DROP curtain:/etc/shorewall# So it should be enabled, right? ---- tcrules ---- 1 eth0 0.0.0.0/0 all 2 eth1 0.0.0.0/0 all 2 eth2 0.0.0.0/0

Season Greetings to all Tom, in your faq, u have this noted: While I am currently using the HTB version of The Wonder Shaper (I just copied wshaper.htb to /etc/shorewall/tcstart and modified it as shown in the Wondershaper README), I treid this with wondershaper, using Bearing Leaf 1.0 stable i even changed the tc command to run_tc, and tried it in both angles, and i receive the following..

I did not subscribe to the list. I''ve been using shorewall for some time and I appreciate it very much. I think it would be useful to have an option to generate a script of the commands Shorewall is about to issue, instead of issuing the commands directly. This script could then be used for revision, modification, and could also be used on another system. I thought about modifying

Hello guys, I past the last days trying to configure my shorewall 4.06 firewall to allow openvpn bridging connection. My scenario is the following: roadwarrior (openvpn client) -------------> Internet ------------> (X.Y.W.Z - eth0) Firewall/Gateway (10.x.x.254 - eth1) --------> Local Lan -------> OpenVPN Server (10.x.x.249 - br0) where 10.x.x.0-254 is my private lan X.Y.Z.W is

http://www.shorewall.net/traffic_shaping.htm Page says run_tc qdisc add dev eth0 parent 1:10 pfifo limit 5run_tc qdisc add dev eth0 parent 1:20 pfifo limit 10 Im willing to _bet_ there is a line feed missing in there ;)

I stumbled upon a problem while upgrading Ubuntu 13.04, Shorewall version from 4.4.26.1 to 4.5.16.1. Everything was working fine before, after upgrading the script wouldn''t start. First some config files. tcdevices: #INTERFACE IN-BANDWIDTH OUT-BANDWIDTH OPTIONS REDIRECTED eth1 - 6300kbit hfsc,classify ifb0 - 6300kbit hfsc

Martin Devera wrote: > If you read the manual, the algorithm will not work correctly > with {,c}burst < MTU ... > devik > I just tried to change {,c}burst to 1600, or leaving them by default but no visible result. here is the latest tc -s -d class show dev eth0 class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level

helo again. I think this question i am asking is worth: we know that pppoe-server creates a pppX device on each connection done to it. So, when i have to shape, i have to shape each pppX connection device on itself alone. What i know is that the borrowing method on one device by itself, e.g. ppp0, alone using HTB or the like. this means that i have to create for another device, e.g. ppp1,

I have - HZ - recompiled to 1000 - class nr 1 - 2kbit ceil 1024kbit - class nr 2 - 16kbit ceil1024kbit But class 1 works with 20kbit/sec and class 2 with 60kbit/sec. The proportion does not seems right. Thank you. _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hello... I have one 2Mbit WAN interfaces and two vlan LAN interfaces - vlan2 and vlan3. I''d like to limit bandwidth something like this: rate 1Mbit ceil 2Mbit for vlan2 and rate 1Mbit ceil 2Mbit for vlan3 with possibility to borrow bandwidth between vlan2 and vlan3. ^^^^^^^^^^^^^^^^^^^ Is it possible to do in any way? regards, -- Michal

I have an PNY NVIDIA Quadro NVS 440 PCI Express x1. It's main feature is it's 4 monitor support. The PCIe x1 port was needed since my workstation is actually an beefy server w/ no x16 slots. Linux support, even when using the binary drivers has deteriorated over the years, especially once the desktops started going '3D'. I went from running on a 4 monitor, single desktop, back

Hello! I have a quite complicated setup. In my network on each interface there is bandwidth limitation for each user. Booth outgoing (on interface itself) and incoming (attached IMQ) traffic. There is main HTB class which limits bandwidth for whole interface and HTB subclasses for each user. Filtering is done with hashing filters. This setup was working correctly. But now in the network I

I''m using a fairly large number of classes, andf borrowing is not working as expected... I''ve called this setting it up on an IMQ device with speed 1200/256 on a 1536/384 line. I''m then throwing a UDP data transfer at it that gets tossed in one of the class under parent 1:6. The classification is working fine, but when I try to ping out, ping times are in the 900ms

Hello to everybody, We want integrate in a router/firewall (Debian Based, 2.6 Kernel), an HTB shaper. The goal is to divide the traffic for classes of workstations, at example in three classes, let say A, B and C. Example: A 70 Mb/s B 20 Mb/s C 10 Mb/s If B don''t make traffic, 7/8 of 20Mb/s must be assigned to A and all the rest at B We have used CBQ and HTB, with poor succes. Anybody

This could be a lot simpler than I think and I''m just missing something obvious! I''m working on a creative collaboration app whereby one user could submit a Story and this can then be forked by another user and worked on seperately. To acheive this I have a has_many association within the same Story model as such: class Story < ActiveRecord::Base has_many

Hello there! Yesterday I started my experiments with HTB. I configured it this way: 1: root HTB qdisc | 1:1 HTB class rate 1000kbit | /-------+------\ 1:40 1:50 1:60 user1 user2 user3 rate 333 & ceil 1000 for everyone. User2 is disconnected and user1 and user3 are downloading. For all the time (t1-t5) there are ONLY these two users downloading! HTB should give

I used Stef Coene''s snmp.pl. #./tc.sh #./get_snmp.pl #./snmp.pl #tc -s class ls dev eth0 class htb 20:1 root rate 80Mbit ceil 80Mbit burst 106440b cburst 106440b Sent 674762 bytes 5660 pkts (dropped 0, overlimits 0) rate 3bps lended: 0 borrowed: 0 giants: 0 tokens: 8313 ctokens: 8313 class htb 20:10 parent 20:1 rate 40Mbit ceil 80Mbit burst 54017b cburst 106440b Sent 670753

I've gone over the data and do not see my error; the dput() output of the data frame and the pdf output of cenboxplot() are attached. The command used: cenboxplot(sb.t$quant, sb.t$ceneq1, range=1.5, main='Total Recoverable Antimony', xlab='Pre-Mining Era', ylab='Concentration (log mg/L)') (on a single line in emacs). The RL on the plot is drawn at 0.01 rather

==================================================================== "What I just said is the fundamental, end-all, final, not-subject-to-opinion absolute truth, depending on where you're standing." Steve Martin ==================================================================== Release Announcements ===================== This is is the latest stable release of Samba

==================================================================== "What I just said is the fundamental, end-all, final, not-subject-to-opinion absolute truth, depending on where you're standing." Steve Martin ==================================================================== Release Announcements ===================== This is is the latest stable release of Samba