similar to: tbf : rate and effective speed (newbie)

Hello, I was attempting to throttle egress traffic to a specific rate using a tbf. As a starting point I used an example from the LARTC howto, which goes: tc qdisc add dev eth1 root tbf rate 220kbit latency 50ms burst 1540 I then attempt a large fetch from another machine via wget (~40 megs) and the rate was clamped down to about 12Kbytes/s. As this seemed too much, I gradually increased

I''m trying to fill a token bucket with enough tokens to burst several gigs of data. However, it doesn''t seem to get any higher than ~3.9GB: >tc qdisc add dev eth0 root tbf rate 1440kbit latency 50ms \ burst 16000000000 >tc qdisc show dev eth0 qdisc tbf 800b: rate 1440Kbit burst 3908420240b lat 2197.8s A smaller attempt of ~1.6 gigs works just fine: >tc qdisc

Hi Everyone, This is a simple question but I don''t understand why the below tbf is not working as expected by throttling traffic to 5kbps If I throttle a PC''s traffic using the below when traffic exceeds 5kbps packets start getting dropped (as they should) but all traffic gets dropped. not just the bit over 5kbps. TC="tc add dev ppp0" $TC parent 8001:2 handle 2:

Hi, I would like to know how to specify the token rate when a tbf qdic is created using tc tool.. Will it be a default value when tbf qdisc is created? This could be a silly question.... im quite new to all these stuff.. but im really interested.. any help will be most appreciated... thanks in advance, sanjeev -- ______________________________________________ Check out the latest SMS

Hi everybody, it is my first message here. I tried to browse throughout older posts but I found no immediate answer. I need to change rate of a tbf queue while ip packets are already enqueued by it. If I go: tc qdisc replace|change|link dev eth0 root tbf rate 180kbit burst 1540 limit 15400 as results all enqueued packets seems to disappear. I can see that from a: tc -s qdisc ls dev eth0

Hi, Can you please explain to me the difference between rate and peakrate, in conjucture to TBF. IMHO, rate : controls the no. of pkts flowing through the pipe, and peakrate : controls the no. of tokens flowing through the bucket. A funtion(?) of peakrate and mtu is rate. If this is true, why do I need to specify both peakrate and rate? Regards, suraj. __________________________________ Do

I''m using tc from iproute-2.6.15 with a 2.6.12 kernel. I was testing the effects of the burst parameter in a tbf qdisc. Basically, I was testing this statement from the tc-tbf(8) manpage: "If your buffer is too small, packets may be dropped because more tokens arrive per timer tick than fit in your bucket. The minimum buffer size can be calculated by dividing the rate by HZ."

Hi, I am a completely newbie, and have been doing intense reading for the entire last week, and have the following novice question: In section 9.2.2.2. of LARTC HOWTO, the following sample configuration given: # tc qdisc add dev ppp0 root tbf rate 220kbit latency 50ms burst 1540 Why is the burst parameter value determined to be 1540? Thanks, Todd

Hi, after opening the AUTH port in my ipchains filter, I still can't get directory listings from ftp.winehq.com. Google shows there was a bug in the ProFTPD 1.2.0pre10 which is used on ftp.winehq.com: "Bug#74153: marked as done (proftpd sometimes refuses to list directories"

I know this will be trivial for most, but I am having trouble with getting my scenario to work correctly. I want to ''tag'' and ''throttle'' the bandwidth to and from a particular client on my lan side. Better yet, I just want to throttle smtp traffic, per say, for that ip. ----lan----------eth1-[linux.box]-eth0----------internet I have used the technique

I just installed CentOS 4.4 on my laptop, having good experience with Debian, Fedora Core 5, and RHEL4. I really like 4.4's overall appearance (meshing of RHEL4 and FC5), but what I have yet to figure out is how to access repositories for applications that are not part of the default install, such as ncftp. I invoked and updated yum, but it had no idea. I would also like to see what

Hi have set the following tbf tc qdisc add dev eth0 root tbf rate 0.5mbit \ burst 5kb latency 70ms peakrate 1mbit \ minburst 1540 I want to add a filter so the ip traffic pass from it.. plz help me __________________________________ Yahoo! Mail Stay connected, organized, and protected. Take the tour: http://tour.mail.yahoo.com/mailtour.html

I presently use TBF with this syntax: tc qdisc add dev eth0 parent 1:100 tbf buffer=15000/8 LIMIT=30000 MTU=1500 parent class is a cbq with rate=128Kbit when I want to add PEAK, I get always RTNETLINK error: Invalid argument. Maybe be I don''t understand this parameter. What I know about it, it''s that it can control short-term burst traffic, and it''s what I need to do.

Hi i have found a problem related with tbf and the latency that the tbf calculates.. I have used the following parameters for burst and limit burst 100Kbit limit 500Kbit lat81.8ms burst 6Kbit limit 6Kbit lat 0us burst 200Kbit limit 100Kbit lat 4294.9s As u can see in the 3rd column the latency for 100Kbit burst and 500Kbit limit is 81.8ms but for 200Kbit and limit 100Kbit is 4294.9s!!! How

I am using tbf to do rate limitation. i set the rate, burst and latency parameters for tbf. but when i start passing data i notice that there is an initial burst and then the rate goes down to the configured level. is this because tbf starts with a full bucket? thanks. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection

Dear friends, thanks for the last advices about TBF. After reading the tbf.pdf document I got a better insight of the problems I had trying to limit the bandwith on my testbed with a high resolution. The question I have now is: Would I get an immediatly better resolution result if I change the #define HZ to 1000 for my Linux box? I have a Pentium Celeron 700 MHz, and I would like to see the tbf

Hi all! I just started to experiment with bandwidth management using tbf. I have the folowing problems with token understanding: 1) What unit is token? Is "1 token = 1 byte" ? If this is so, then with rate=0.5mbit and HZ=100 the bucket gets filled with 0,64kb (655 tokens) every 10ms? 2) How much tokens are used for one packet (1500)? 3) And token unrelated question. Does

Quick question: How do I delete an ingress tbf? [root@atlas root]# tc qdisc qdisc tbf ffff: dev eth0 rate 50Kbit burst 2999b lat 1us [root@atlas root]# tc qdisc del dev eth0 ingress RTNETLINK answers: Invalid argument _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hello, I have one Q. What is better when using as leaf in one leaf with several hosts (like subnet) to splice traffic equaly to user number? Like 2 users = 256/2, 3 = 256/3 and so on. WRR was pretty good for this job, but it''s only for 2.4.21 kernels and mine''s 2.4.22. So what is better: SFQ or TBF? -- Artūras Šlajus _______________________________________________

Hello Please give advice in selecting suitable QoS Solution for our device. It contains one WAN port and a LAN port(4 port switch). The WAN will be connected to an ADSL modem(so we don`t know the bandwidth in advance for the WAN and depends on the ADSL connection taken). We need to give highest priority to the Voice and control the WAN bandwidth to 2Mbps. I tried with the TBF by giving 500kbps