similar to: wondershaper

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

Hi, I have a question conercing wondershaper. I''m using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper. On start up of wshaper, there are no errors or any other problems but I''m not sure if it''s running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I

Hello Thilo, What did you find superior with CBQ-wondershaper over HTB-wondershaper? We have not been using wondershaper specifically but our simple tests so far seem to show that htb is much easier to configure for a given target shape (i.,e accurate) compared to CBQ. Torsten -----Original Message----- From: Thilo Schulz [mailto:arny@ats.s.bawue.de] Sent: Saturday, June 14, 2003 8:55 AM To:

Hi, When i do ''wshaper start'' the interface i have defined stops routing traffic for some reason. It resumes routing when i do ''wshaper stop''. I''m using debian stable (3.0 woody) with debian''s default 2.4.18-686 kernel. When I run the script I get no errors, and when I do a ''status'', everything looks correct. Can ANYONE

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

Hi Guys, I''m asking this question again because I have exhausted resources for understanding how to get it to work. I''ve read the howto on getting traffic shaping to work (shorewall''s web site) as well as trying out wondershaper''s htb and cbq scripts. Somehow both does not seem to happen as I want it to. I''ve also read through the lartc

I have wondershaper to limit my upload at 400kilobits (my line is 600kbps). I do a lot of torrent seeding and I dont want my pings killed when I''m uploading so I set low prority source ports as follows (by the way, I have bittornet to only use ports 6881-6910): NOPRIOPORTSRC="6881 6882 6883 6884 6885 6886 6887 6888 6889 6890 6891 6892 6893 6894 6895 6896 6897 6898 6899 6900 6901

Hi, first of all, let me thank you for your great Shoreline Firewall. I use it with great success at home (protecting my WiFi connection). And now if I could have a question about traffic shaping. I did read everything I could find but I still have two problems: first, the MARK from tcrules is not working in HTB based simple tc filter line ("handle $MARK fw classid 1:20"). If I switch

Hi all, ive got wondershaper working well with the highest download while maintaing minimal latency but the problem is this: ive got 2 nics in the linux router eth0 and eth1. eth1= internet interface but this is connected to a router say 10.0.0.190, now off that router there are other servers, mail server, domino server etc now if i shape on eth1 ingress and egress using the wondershaper script

Hello, I am trying wondershaper-1.1a on a friend''s pppoe connection on her Linux box. There are a few things I don''t understand. 1. She has pppoe connection so should DEV=eth0 or DEV=ppp0 ? 2. Her ISP just says on her payment bill that the speed is 128kbps, but doesn''t mention any downlink/uplink speed, so in that case what should be, DOWNLINK= and UPLINK= ? 3. She

Hi, I really like the wondershaper script, it works very well for me. My question is this. Is there a way to get certain remote hosts to be excluded from the shaping? I ask because I don''t have my box connected directly through the net. It sits behind a nat device, and has ports forwarded in for services. I''d like to limit the ports and services, but only to things going outside

Hi ! I´ve been using the wonderful wondershaper from chapter 15.8 of the LARTC Howto for some time. It´s really wonderful. Actually, I use the version from http://freshmeat.net/projects/wshaper/?topic_id=87 Now I tried to put some hosts to low priority, and it doesn´t work. The traffic is splitted equally between the noprio and the other hosts. Is this because I use ip masquerading, and all

I tried installing the WonderShaper on my internal link, mostly to get the SFQ installed. I set uplink and downlink to 100000 to match the link speed and changed the bandwidth on the cbq line to 100mbit. This killed transfer speed *to* the box, knocking it from 30-40 Mbps down to about 800 kbps. Commenting out just the ingress control restored the speed. What about the ingress policer would do

Hi ! I wanted to shape my analog modem connection so I took these two lines from the ''wondershaper'' script: tc qdisc add dev $DEV handle ffff: ingress #tc filter add dev $DEV parent ffff: protocol ip prio 50 u32 match ip \ src 0.0.0.0/0 police rate ${DOWNLINK} burst 10k drop flowid :1 with DEV=ppp0 and DOWNLINK=24kbit. But, when I activate it, nothing comes back from the

Season Greetings to all Tom, in your faq, u have this noted: While I am currently using the HTB version of The Wonder Shaper (I just copied wshaper.htb to /etc/shorewall/tcstart and modified it as shown in the Wondershaper README), I treid this with wondershaper, using Bearing Leaf 1.0 stable i even changed the tc command to run_tc, and tried it in both angles, and i receive the following..

Hi, I''m really new to traffic shaping and try to implement the wshaper.htb script. I have a linux box that serves as vdr, mldonkey, samba, apache and mailserver (imap), connected to my LAN with 100mbit. I''m connected to the inet via adsl with a hardware router/firewall, got 384k downlink 64k uplink. When I have mldonkey running, imap (via Outlook) gets *very* slow (mails with

I''m having a network inside of a dsl modem and I''m using wondershaper on the computers to be able to surf while bulk downloading. The problem is that also the internal traffic is shaped, which means the internal network is at 200kb/s, instead of 100Mb/s. Is there a way to exclude the internal adresses from the wondershaper rules, or is there any other good way to solve this?

Hello, i´ve installed a Suse 8.1 minimal System with iproute 2.4.7 and iptables, Suse default Kernel 2.4.19. When I start the Wondershaper 1.1a Script I get the following Error: CBQ: "allot" is required to set WRR parameters. /home/skripte/./wshaper: line 72: allot: command not found CBQ: "allot" is required to set WRR parameters. /home/skripte/./wshaper: line 78: allot:

Hi, I just installed wondershapper 1.1a on my ipcop firewall box. I have roadrunner cable with a ftp server setup. My download speed is 2mbit (I get 225 KBytes) and my upload is 384kbit (I send at 43 KBytes). What should the settings in wshaper? I can ping yahoo.com at 90msec with little traffic.....and at around 220msec with full upload traffic. Mark

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello, been awhile since I''ve written. I now have a situation where I get to use traffic shaping for a client. ~ We implemented the WonderShaper script on our own firewall and experienced no problems. I made some modifications to it to add IPSec protocol packets into the 1:10 high priority class using the u32 filter. ~ So far on our