similar to: Statistics truncated

Hello everybody, sorry for bothering you, but after some hours, I''m stuck. I''m living in a student''s foundation where I want to connect lots of people to a tiny DSL link. We have exactly four types of traffic. We want a really hard PRIO solution (as I promised to someone that group X will only use the link capacity which isn''t used by group Y). I could make a

Hello, I am using a simple script, which is based on prio. The point is, that it is not possible to use htb on wifi networks, so I thought that prio will work fine, but it does almost nothing. All I wanted was to make the important packets like icmp, games, VoIP,... to go first, and to slow the things like FTP data transfer, etc. When I use $TC -s qdisc show dev ${IFACE}, I see, that the

Hi, I have a router/firewall running Linux (like the most of you) and I wanted to do some traffic control. I''ve created an root PRIO qdisc like the example in paragraph 9.5.3.1 (http://www.lartc.org/howto/lartc.qdisc.classful.html#AEN903) with three SFQ child-classes. I wanted for interactive (ssh, telnet, ftp-control) and dns-traffic to be placed in the first queue, http should go in

I am completely new to this.. I am trying to make simple traffic control.. I have read quite some manuals and posts that i found, but i don''t understand much, i think.. My situation is: i have linux server which i am using for firewall for local network.. also on same linux server i have torrentflux for downloading torrents.. What i want to do is to give priority to local clients(2-3

Hello, I have a problem with simple traffic shapping in shorewall, my current configuration is: zones vlan10 ipv4 # interfaces vlan10 vlan10 detect tcpflags,routeback shorewall.conf TC_ENABLED=Simple tcinterfaces vlan10 Internal 1mbit:50kb shorewall show tc Device vlan10: qdisc prio 5: root refcnt 2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

hi below is sysvinit script for handling tcng-script .... please excuse my bad bash skils, correct me where i''m doing stupid things :") what is left... many things, if i have time i will implement them too : - start [devices] - and then correct handling of service lock files i.e. per device lock file - stats blah ... - all ideas are welcome !! - test or some such, i mean the

Hi Recently I upgraded my kernel to 2.6.11 (debian) and applied some patches from pom-ng (netfilter) and the iproute2-ss050330 package I have been experiencing a lot of crashes in the kernel (snip below) ================================== Apr 5 20:00:21 sydlxfw01 kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000221 Apr 5 20:00:21 sydlxfw01 kernel: printing eip:

I thought I had this all worked out, but it seems not. The following tc configuration: tc qdisc del dev ppp0 root 2> /dev/null > /dev/null tc qdisc add dev ppp0 root handle 1: tbf rate 120kbit burst 1200 limit 1 tc qdisc add dev ppp0 parent 1:1 handle 2: prio bands 3 tc qdisc add dev ppp0 parent 2:1 handle 10: sfq perturb 20 tc qdisc add dev ppp0 parent 2:2 handle 20: sfq perturb 20 tc

Hi, I try to use the PRIO scheduler on a 2.6.17 kernel. I use a simple configuration : $TC qdisc add dev $dev root handle 1: prio bands 2 priomap 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 $TC qdisc add dev $dev parent 1:1 handle 10:0 sfq perturb10 $TC qdisc add dev $dev parent 1:2 handle 20:0 sfq perturb 10 And i put filters for my trafic, the 2 streams are correctly put in each

Hi all, based on the information in the "Linux Advanced Routing & Traffic Control HOWTO", I was trying to set up traffic shaping on my firewall. While I found the HOWTO very useful, in the process I ran into some problems that I did not forsee: According to the HOWTO it seems that it should have worked, even after spending some time going through the sections looking for answers,

Hello All, I am battling a problem I don't know how to fix... Here is the scenario: Fractionated T1 with 1-6 channels voice, 21-24 channels data. Comes into a box with Digium T100P, splits off data channes with HDLC, to devicec pvc0, This works fine, but I have a routing problem getting to my machines! Here is the current set up... sethdlc hdlc0 fr lmi ansi sethdlc hdlc0 create 44

Hi Gang, I''m still experiencing some bandwidth starvation with my script (below), so I decided to look at the statistics by using: tc -s qdisc show dev eth0 (where eth0 is the interface I''m trying to rate-limit outbound packets) I get, for example: qdisc sfq 21: quantum 1514b perturb 10sec Sent 133527926 bytes 413260 pkts (dropped 0, overlimits 0) qdisc sfq 20: quantum

Hello! I have an internet connection of 64kbps garanteed in a channel of 256kbps. On this connection the metropolitan speed is 10Mbps and in the provider''s network the speed is 100Mbps. I have a few clients behind my linux box and i want to set up some limitations because some of them are using it irrational. I am marking the packets with 0 for internet; 1 for metropolitan 2 for

Hi all. I have a bridge running Linux 2.4.24 that I use as a bandwidth manager on a broadband wireless network. I''m using HTB and SFQ to prioritize that share bandwidth on a per-cell basis. My IP tables rules divide the traffic based on IPand traffic type (using layer-7 filter and ipp2p). My goal is to make sure that p2p traffic on the network doesn''t sink all of the

Hi, Is it possible to attach another qdisq under a HFSC classfull ? I try it and the configuraton works : $TC qdisc add dev $dev root handle 1: hfsc default 30 $TC class add dev $dev parent 1: classid 1:1 hfsc sc rate ${RATE}mbit ul rate ${RATE}mbit $TC class add dev $dev parent 1:1 classid 1:10 hfsc rt umax 1500b dmax 30ms rate 200kbit $TC class add dev $dev

Hi Stef, Sorry to write to you directly but my list membership is not working, I receive the archive but cant send to the list, cant delete myself because I don''t exist and can''t rejoin as they say I do exist, anyway hope you don''t mind Can you tell me what the difference between these two scripts is please. What I want to achieve is a high speed channel 1000kbit from

Here goes the filter statements: #Initializing traffic control... tc qdisc add dev br0 root handle 1:0 htb #Loading queue disciplines for plis230 network... tc class add dev br0 parent 1:0 classid 1:1 htb rate 512kbit ceil 512kbit #Loading queue disciplines for pmad048 network... tc class add dev br0 parent 1:1 classid 1:20 htb rate 30kbit ceil 30kbit #server queue tc class add dev br0 parent

Hello List, I use HTB in a ~80 users serving router with kernel 2.4.20. eth0 is the internet interface (half-duplex 1Mbit), eth1 the internal interface (100Mbit full duplex) cause of the fact that the router also serves as a http-proxy (squid) i thought setting up the default class on eth1 with the real upload-speed (100Mbit) would do the job, i.e. shaping normal stuff to 1Mbit except local

Hi everyone, My HTB script is showing me those "r2q change" warnings. I read that I should test with r2q values to gain accuracy and stop the warnings but I made some tests with r2q and with burst and I still get the warnings. Any ideas on this issue will be very helpful. The script seems to be working as the bandwidth for the IPs is being shaped. The NIC works at 100mbit and the