similar to: flowid - classid ?

For simplicity, I tried this: tc qdisc add dev eth0 root handle 1: prio tc qdisc add dev eth0 parent 1:1 handle 10: sfq perturb 10 tc qdisc add dev eth0 parent 1:2 handle 20: sfq perturb 10 tc qdisc add dev eth0 parent 1:3 handle 30: sfq perturb 10 tc filter add dev eth0 protocol ip parent 1: prio 2 flowid 1:1 The last line prints: Unknown filter "flowid", hence option "1:1"

Hi all Can anybody pls explain me the difference between classid and flowid. In which scenario we may need to use either of one. Any help will be greatly appreciated. regards Vinoos. _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi, All, I have a class 1:10, it seems if I use netfilter mark as classifier, then the class will be refered as classid 1:10, however, if I use u32 as classifer, then the class should be refered as flowid 1:10, is it right? Thanks in advance, James

I downloaded iproute2-2.4.7-now-ss010824.tar.gz and I did patched tc with the htb3.6_tc.diff from htb3.6-020525.tgz and when I try to use a htb script I get just errors. I did not patch the kernel, since I use kernel 2.4.21 and I saw on - HTB Homepage that I need to patch it only if I run version 2.4.20 or earlier. Do also need the kernel patch ? Or maybe is something else wrong? RTNETLINK

hello to all i''m trying to set a filter but doesn''t want to work. i''ve set ut the qdiscs and the classes like this : tc qdisc add dev ppp0 root handle 1: htb default 20 tc class add dev ppp0 parent 1: classid 1:1 htb rate 120kbit tc class add dev ppp0 parent 1:1 classid 1:20 htb rate 30kbit ceil 120kbit tc class add dev ppp0 parent 1:1 classid 1:21 htb rate 30kbit ceil

Hi Is there a way of marking packets by mac address instead of ip or ports using a "tc filter u32 match"? I read somewhere that I could use the offset -8 and -14 to grab the mac addresses but if I use anything lower than -8, for example -9, I get an error. I''m modifying the wondershaper script to cap the download speed by mac address. Any sugestions?

I try to shape traffic using HTB and mark packets within iptables using PREROUTING. But the filterrules seems to ignore the marks set with PREROUTING Only POSTROUTING marks are accepted. First my configuration I have a router connected to the internet via ADSL over interface ppp0. eth0 is a tunnel to ppp0 and eth1 serves the LAN. LAN is 192.168.57.0/24 on 10Mbit ppp0 is 80.126.16.44 on

Hi, here I have another newcomer question :-) in the section 9.6.1 of this how too http://tldp.org/HOWTO/Adv-Routing-HOWTO/lartc.qdisc.filters.html we can read commands about filters : ------------------------------------------ # tc filter add dev eth0 protocol ip parent 10: prio 1 u32 match \ ip dport 22 0xffff flowid 10:1 # tc filter add dev eth0 protocol ip parent 10: prio 1 u32 match \

Hello! My system is: Internet ADSL(PPPoE) ---> ppp0 [LINUX server(router)] eth0 ---> LAN Server(router) is running on LINUX Slackware 8.1. I have recompiled a 2.4.22 kernel, enabled all QoS support in the kernel config, including HTB. My ADSL bandwidth is 256Kbit/s for download and 64Kbit/s for upload. I use the following HTB+IPTABLES configuration, because I want to reduce bandwith for

Hi all, Im new to all this, and am still trying to get my head qround some of the concepts of how this all works. Ive read the howto''s, man pages etc. Ive setup packet shaping on my router/server box using HTB and SFQ, but its not working the way i would like. Im after shaping that has "weights" for classes so that a lower priority class will slow down when a higher class

I have: tc qdisc add dev imq0 root handle 1: htb default 30 tc class add dev imq0 parent 1: classid 1:1 htb rate 512kbit ceil 512kbit tc class add dev imq0 parent 1:1 classid 1:30 htb rate 64kbit ceil 512kbit then: iptables -t mangle -A PREROUTING -i ppp0 -s 192.168.2.2 -j IMQ --todev 0 tc class add dev imq0 parent 1:1 classid 1:22 htb rate 64kbit ceil 128kbit tc filter add dev imq0 protocol

Hi, with the attached config my gaming ping is still +20ms, even if the line isn''t saturated..can anybody give me a hint how to get a better response time? my line: 1024/128kbit outbound: one htb qdisc for gaming (7kbps) prio 0 ceil 14kbps<- should get more traffic when needed. Htb again for irc and default. inbound: css, irc, p2p, default <- same shema as before, give css

Hi All, I''ve been playing with QOS for a short while now and have worked out how to do what I want using HTB. Great queuing discipline btw. My problem is the tc filters I want to setup aren''t working because iptables is getting to the packets first and mangling the src address. The iptables script I am using is MonMotha''s Firewall 2.3.8 and it includes lots of nice

I run a small Linux webserver and NAT router from my cable modem at home. Whenever someone starts an http download, all other traffic from my LAN is starved. Bandwidth is not really an issue, but latency is particularly horrible -- pings that usually come back in 20ms can take up to 600ms while the web server is active! I set up QoS (netfilter+iproute2) on the NAT machine in an attempt to give

Dear all, I want to make a filter for all IRC-Dalnet traffic, so I want to put all traffic for port 6660, 6661, 6662, 6663, 6664, 6665, 6666, 6667, 6668, 6669, 7000, 7001, 7002, and 8000 to a class. So, I create a TC script as below. I''m sure, it is not effective, and we can write it in simpler. I need help, how to make my script below are simpler. The simpler, the better. Thank you

Hey, I have a problem adding a filter matching anything, here is my setup: ############### tc qdisc add dev eth0 handle 1: root prio tc qdisc add dev eth0 parent 1:1 handle 10: pfifo tc qdisc add dev eth0 parent 1:2 handle 20: tbf latency 50ms rate \ 128kbit burst 256kbit tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 666 fw \ flowid 1:2 tc filter add dev eth0 protocol ip parent

I''m trying to setup traffic shaping on my linux gateway/router. The system has 3 interfaces: eth0 - My LAN - with IP address 192.168.0.254 eth1 - The ethernet connection to which my ADSL modem is connected. This has a 10.25.x.x IP, more on this later. The ADSL link has an upstream of ~1.2mbit. ppp0 - The PPP connection which is my WAN connection, with a real world IP. The system acts

Le 26 juil. 07 à 13:55, Georgi Alexandrov a écrit : > Vincent Dautremont wrote: > >> Hi, >> here I have another newcomer question :-) >> in the section 9.6.1 of this how too >> http://tldp.org/HOWTO/Adv-Routing-HOWTO/lartc.qdisc.filters.html >> we can read commands about filters : >> ------------------------------------------ >> >> # tc

People, I''m trying to set up the tc filters for a PRIO queue. I''m basing it off of marked traffic via iptables. For example, I''ve marked two classes of traffic with ids "2" and "4", and now I''m filtering those to bands 1 and 2. tc filter add dev eth0 parent 1: prio 0 protocol ip \ handle 2 fw flowid 10:1 tc filter add dev eth0 parent 1:

Hello At first I must tell you that I´m a real newbie with Linux (and english as well...) I´m using 2 vlans and shaping works quite well without vlan Now I want to do load balancing at these vlans. Any vlan should get the same minimum/maximum bandwidth of download and use the bandwidth that isn´t used by the other one at the moment. But with vlan the shaping doesn´t work. Can you please tell me