similar to: How to do ensure bandwith

We have been using HTB for last 10-11 months without any problem. But from last few days we have been facing huge packet loss when we turn on traffic shaping using HTB. I upgraded to 2.4.24 kernel (without any htb patch), still there is same problem. Avg. traffic is around 2Mbps and 4Mbps at peak hours. There are around 110 HTB classes and SFQ attached to each class. We are using 4 port Tulip

Hi, The CBQ config file shud be some thing like this. DEVICE=eth0,10Mbit,1Mbit RATE=50Kbit WEIGHT=5Kbit Shall i hardcode the DEVICE BW as 10/100 Mbit or Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other? C''d anybody can give a suggestion over this? thanks

Hi, I have some interesting problem with htb , I set up root class and sub-classess: $TC qdisc add dev eth0 root handle 1: htb $TC class add dev eth0 parent 1: classid 1:1 htb rate 1990kbit ceil 2000kbit $TC class add dev eth0 parent 1:1 classid 1:10 htb rate 190kbit ceil 200kbit $TC class add dev eth0 parent 1:1 classid 1:11 htb rate 1400kbit ceil 1600kbit $TC class add dev eth0 parent 1:1

I wan to share internet to these 12 PCs. But my traffic control is not working. I''m using IP Masquerading to route internet to the LAN eth0 - LAN interface eth1 - Internet interface this is my firs htb script: #!/bin/bash tc qdisc del dev eth1 root handle 1: tc qdisc add dev eth1 root handle 1: htb default 30 tc class add dev eth1 parent 1: classid 1:1 htb rate 25kbps ceil 48kbps #tc

Hi everybody! I''ve been trying with htb and tc filter. It seemed to work fine, but after testing with ethloop I''ve realized that traffic is not being distributed through the leaves as I thought. When sending packets to 1:10 and 1:11 at the same time, there''s no bandwidth sharing. There''s no traffic through 1:11 until traffic through 1:10 has finished. Though

I''m trying to implement something similar the the diagram in section 9.5.2.1 in the LARTC HOWTO, but must have missed something somewhere :( I''m trying to hack up wondershaper, as it looked like a good place to start.. Here''s where I currently at, but I''ve tried alot of different things, all failing, some worse than others. The end result is to throttle back 126

HTB and imq was used to control traffic. AC="tc class add dev eth0 parent" $AC 1: classid 1:1 htb rate 100kbps burst 2k $AC 1:2 classid 1:10 htb rate 50kbps ceil 100kbps burst 2k prio 1 $AC 1:2 classid 1:11 htb rate 50kbps ceil 100kbps burst 2k prio 1 please tell me the range of "prio" _________________________________________________________ Do You Yahoo!? 新鲜到底,娱乐到家 -

Hi ; MY script: tc-htb3 qdisc del dev eth2 root ipchains -F tc-htb3 qdisc add dev eth2 root handle 10: htb default 20 r2q 40 tc-htb3 class add dev eth2 parent 10: classid 10:1 htb rate 50Mbit burst 2000 tc-htb3 class add dev eth2 parent 10:1 classid 10:100 htb rate 12mbit ceil 50mbit prio 1 tc-htb3 class add dev eth2 parent 10:1 classid 10:20 htb rate 38mbit ceil 50Mbit prio 8 ipchains

To stress the urgency and importance of my questions, I am willing to pay $100 to the first person that can provide me with the scripts/ rules that will work in my SnapGear firewalls that will solve the problems I am having. Please see the following post: Linux QOS and prioritization of real-time data (RTP/VoIP) Thank you!

Hi everyone, My HTB script is showing me those "r2q change" warnings. I read that I should test with r2q values to gain accuracy and stop the warnings but I made some tests with r2q and with burst and I still get the warnings. Any ideas on this issue will be very helpful. The script seems to be working as the bandwidth for the IPs is being shaped. The NIC works at 100mbit and the

Hi, tc qdisc add dev eth0 root handle 1: htb tc class add dev eth0 parent 1:0 classid 1:1 htb rate 2000Kbit ceil 2000kbit tc class add dev eth0 parent 1:1 classid 1:2 htb rate 1200Kbit ceil 2000kbit tc class add dev eth0parent 1:1 classid 1:3 htb rate 800Kbit ceil 2000kbit tc class add dev eth0 parent 1:2 classid 1:21 htb rate 600Kbit ceil 2000kbit tc class add dev eth0 parent 1:2

Hey all. I''m trying to set up QoS using the HTB qdisc in a very basic setup, but it the example shown in the howto doesn''t seem to be working. While the packets show up in the correct classes, they appear to be completely ignoring the rates, meaning nothing gets shaped. My setup is that I''ve got a a bunch of machines behind my firewall/router: 1.2.3.1

Hi, I''m fighting seriously with a most simple HTB setup. I''d like to share the incoming 64kbps into 5 and 59 for two different machines under NAT. HTB seems to hold the required limits when ceil is not set (no borrowing), but when borrowing enabled it seems to share equally rather then keeping the specified ratio. My setup is below. A typical output of "tc -s -d qdisc

I''m using htb classes on my firewall to queue traffic and implement different restrictions on different protocols. tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 1: htb default 190 tc class add dev eth0 parent 1: classid 1:3 htb rate 2mbit burst 30k tc class add dev eth0 parent 1:1 classid 1:90 htb rate 50kbit ceil 384kbit burst 5k tc qdisc add dev eth0 parent 1:90 handle

Hi, I have a problem with ''tc filter'' on a 2.4.22 kernel from Slackware 9.1 distribution. The tc command binary is from htb3.6-020525.tgz (http://luxik.cdi.cz/~devik/qos/htb) I''m trying the following command sequence: tc qdisc add dev eth0 root handle 1: htb default 1 r2q 1 tc class add dev eth0 parent 1: classid 1:1 htb rate 1200kbit ceil 1200kbit tc class add dev

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

dear All, I'm a new student and my job is too shapping bandwith for our campus faculty network. I want to implement htb with Redhat-9.0 distro. does this distro kernel support htb and tc good ? or i should apply some patch or upgrade kernel ? regards reza

Hello good day to all ... this is my setup 1 Linux Wireless Access Point, connected are 4 wireless gateway in which i needed to apply shaping ... ok here is the weird part... clients on each gateway download files from the Acess Point ... a 500 mb file through ftp on gateway 1 which is up to 64 kbps ... the result is from 60-64 kbps speed which is fine ... on gateway 2 which is 128 kbps ... the

HTB and imq was used to control traffic. AC="tc class add dev eth0 parent" $AC 1: classid 1:1 htb rate 100kbps burst 2k $AC 1:2 classid 1:10 htb rate 50kbps ceil 100kbps burst 2k prio 1 $AC 1:2 classid 1:11 htb rate 50kbps ceil 100kbps burst 2k prio 2 $AC 1:2 classid 1:12 htb rate 50kbps ceil 100kbps burst 2k please tell me if i do not set prio, what is the default prio? low delay class

Hi I have setup iproute2 and need a bit of help reading the stats from it ===== output qdisc htb 1: r2q 10 default 20 direct_packets_stat 0 ver 3.17 Sent 547326809 bytes 1342627 pkts (dropped 9303, overlimits 2817572 requeues 0) backlog 46p qdisc sfq 10: limit 128p quantum 1514b flows 128/1024 perturb 10sec Sent 41874343 bytes 730889 pkts (dropped 0, overlimits 0 requeues 0) qdisc sfq