similar to: New Traffic Control GUI

hi there, is there any possible way to control traffic in child??? class with selected protocols for example http i try to use this script but its now working in theory: there is root class 1:0 with subclass 1:2 in class 1:2 all ip adresses have their bandwidth limit 1:{iden} and now i try also control bandwith in this class i.e. if class 1:{iden} have 190kbit i want 95kbit with burst to 190kbit

Hello all. We have three tunnels over the internet between our "central" gateway and some branch office gateway. Each gateway has eth0 on its LAN an eth1 on the internet. We use DSL lines and eth1''s have the internet IP directly attached on it. Each gateway, also, acts as iptables NAT gateway. The outgoing bandwith is 300 kbit, and we tried this (i.e.) on each tunnel: tc

Hello! My system is: Internet ADSL(PPPoE) ---> ppp0 [LINUX server(router)] eth0 ---> LAN Server(router) is running on LINUX Slackware 8.1. I have recompiled a 2.4.22 kernel, enabled all QoS support in the kernel config, including HTB. My ADSL bandwidth is 256Kbit/s for download and 64Kbit/s for upload. I use the following HTB+IPTABLES configuration, because I want to reduce bandwith for

hello again, I got some just preliminary results .... hope someone can explain them to me... As I already told I have the following config : egress { class (30kbps) {sfq}; class (50kbps) {sfq}; class (80kbps) {sfq}; class (30kbps) {sfq}; class (50kbps) {sfq}; ...hundreds like this... class (10kbps,default) {sfq}; } What I got is traffic starvation very often for a period of ~30 sec.. as

Hello again, First, excuse me for my poor english. I''m trying now to make bandwith control in a firewall machine running Shorewall. This machine is also a bridge using bridge-utils bridge-utils-devel. It is a mandrake 10. The configuration is something like this: FTP/Webserver ------| eth0 eth1 Mailserver

Hello again, First, excuse me for my poor english. I''m trying now to make bandwith control in a firewall machine running Shorewall. This machine is also a bridge using bridge-utils bridge-utils-devel. It is a mandrake 10. The configuration is something like this: FTP/Webserver ------| eth0 eth1 Mailserver

hi everybody. im trying to set up an QoS config, using layer7 (http://l7-filter.sourceforge.net/) for protocol detection. im suposing 3 clients with this configuration: 3 clients: 1.2.3.1 , 1.2.3.2 , 1.2.3.3 1.2.3.1 has 256kbit bandwidth "guaranteed" clients 1.2.3.2 and 1.2.3.3 has 256kbit bandwith so im marking every packet using layer7 iptables module, classifying them in three

Hi all, I have read the larc howto and I need to apply a traffic shaper with this configuration: router / two interface etho and eth1 lan lan is on eth1 and on eth0 I''ve the dsl connection (1.2 Mbit / 256 kbit) I need to limit the bandwith towards lan and I''ve thought at HTB and tcng. I write the script belove. I want limit the p2p and ftp (ssh and irc) connection at 15

Hello everyone, First of all, sorry for my poor english. I''ve been working with this for a few weeks and I''m getting sick... I''m trying to control the bandwith in my network using the following script. The machine where the script is running makes NAT, eth0 is connected to the router and eth1 is connected to the Lan. When I run the script it doesn''t appear any

Hi, I try to shape my incoming traffic. I have 2MBit/s DSL bandwith and the following ruleset (on the internal interface): $INT="eth1"; $INT_NET=192.168.1.0; $MAX_IN=2Mbps; dev $INT { egress { class (<$int>) if ip_src:24 == $INT_NET; class (<$ssh>) if tcp_sport == PORT_SSH; class (<$smtp>) if tcp_sport == PORT_SMTP; class (<$http>) if

Hello everybody, I am trying to understand the Advance routing and Traffic control. In the examples section of the how to an example script is given. Section 15.8.2 (the ultimate setup for Your internet connection) The example says download is 800 and upload is 220 ###### uplink # install root CBQ tc qdisc add dev ppp0 root handle 1: cbq avpkt 1000 bandwidth 10mbit Maybe I am

Hello, I''m trying to get lossless VoIP traffic over my 3000k/500k ADSL line. Shaping outgoing traffic is no problem: I set total ceil for outgiong device (ppp0) to 450kbit and put VoIP into highest prio class. Even during full upload the voice is clean on the other end. Now I tried to get the same result for incoming data. I attached HTB to eth1 where the incoming voip traffic is

Hi all, ive got 2 internet connections set up via the nano howto (which are working great) and we are running NAT. Was looking in to qos mainly to stop large http downloads/ftp downloads from hogging the line so that browsing for other users doesnt slow to a crawl, but if the line is free and no one is doing anything then for it to use the available bandwith. The wondershaper sounded exactly what

I have htb on 486 sx with 16mb ram. Slackware 9.1. Connection : dsl 1Mbit. 486 works as router and trafic shaper for network made of 12 pc''s. it does the job quite well, but when i play Counter-Strike or connect to my 486 via ssh (on lan), i get huge lag every 11-20 sec. when i connect to 486 via ssh and run iptraf program i see all the trafic, and after a while when lag comes the

Hello list, I discover strange behaviour of shaping traffic that i setup from Shorewall-4.0.2. I know that this is not Shorewall problem but may be somebody from list can help me or explain this situation. I have follow interfaces in 'tcdevices' files: #INTERFACE IN-BANDWITH OUT-BANDWIDTH # $EXT_IF 500kbit 248kbit $INT1_IF 500mbit

hi there, is there any possible way to control traffic in child??? class with selected protocols for example http i try to use this script but its now working in theory: there is root class 1:0 with subclass 1:2 in class 1:2 all ip adresses have their bandwidth limit 1:{iden} and now i try also control bandwith in this class i.e. if class 1:{iden} have 190kbit i want 95kbit with burst to 190kbit

Dear members I''m new to this list and also new to tc command. I have a subnet with over 30 pc which have ip addresses from 172.16.1.1/16 range.I want that each computer in my subnet can work with internet with maximum 6k for download and maximum 6k for upload.when i run the following tc commands from my bridge the first pc works well but the second pc can not work with 6k and it has an

hi there, is there any possible way to control traffic in child??? class with selected protocols for example http i try to use this script but its now working in theory: there is root class 1:0 with subclass 1:2 in class 1:2 all ip adresses have their bandwidth limit 1:{iden} and now i try also control bandwith in this class i.e. if class 1:{iden} have 190kbit i want 95kbit with burst to 190kbit

hi all i want to first apollogiaze if my message will annoy you(my guess is because it will be quite large:)) i have the following situation on my hands i was recently faced with the problem of traffic shaping/bandwith limiting. my setup is(very common i guess) -internet comming in(going out) through eth0 -internet is being "shared" with the private local network via eth1. i