similar to: Ultime traffic conditionner

I have wondershaper to limit my upload at 400kilobits (my line is 600kbps). I do a lot of torrent seeding and I dont want my pings killed when I''m uploading so I set low prority source ports as follows (by the way, I have bittornet to only use ports 6881-6910): NOPRIOPORTSRC="6881 6882 6883 6884 6885 6886 6887 6888 6889 6890 6891 6892 6893 6894 6895 6896 6897 6898 6899 6900 6901

Hello all, Im new using tc, ive been reading the howto at least 2 or 3 times, but there''s a lot information to aquire all of it quickly. I''ve installed a linux box as firewall for a wireless Network in a hotel, this box is a radius for the access points and it uses iptables to redirect and permit/deny the customers to use the net. So it uses iptables to count the bytes to

Hello! My system is: Internet ADSL(PPPoE) ---> ppp0 [LINUX server(router)] eth0 ---> LAN Server(router) is running on LINUX Slackware 8.1. I have recompiled a 2.4.22 kernel, enabled all QoS support in the kernel config, including HTB. My ADSL bandwidth is 256Kbit/s for download and 64Kbit/s for upload. I use the following HTB+IPTABLES configuration, because I want to reduce bandwith for

Hi everybody. I have a dilema and I think you guys can help me out. I am trying to shape the bandwith for about 500 clients, and I want the bandwith to be alocated dynamicly. Lets say I have 4 MB bandwith. I give each ip (500 IP''s) a sustained rate of 4 KB/sec . I wonder if I can shape the bandwith so when for example only 100 clients are online, to give them a rate of 4MB/100. How can

I have clients, which connectin to Internet through vpn. I want to dynamically share bandwith between vpn connections, so if there few connections, then they get all bandwith, if more then they get their minimal guaranteed bandwith. my idea is: ip-up.local: tc class add dev $DEV parent 1:1 classid 1:2${1/ppp/} htb rate $[$RATEUP/$VPNS]kbit ceil ${RATEUP}kbps tc filter add dev $DEV protocol ip

Hi, If I have a DSL router with 300kpbs upload bandwith: Linux(eth0) ---(100Mbps)---> DSL ---(300kbps)---> INTERNET Which is the recomended value I must set in my QoS setup for the maximum outbound bandwith of my ethernet interface ? The max of 300kbps or something less like 290kbps ? Especify less than the maximum available bandwith is advisable to ensure that the QoS algoritms goes

I have a existencial problem. There are some provider that offer the service of bandwith asimetric as download/upload link as for example 512/256. but most of them offer not exclusive this amount of transmission or reception capacity. They usually offer the service with more users as a ratio of 1/10. How I can design a appropriate diagrama with htb where the amount of bandwith could vary.?

Dear members, I am trying to share the bandwith for all users fairly. because some users heavily uses p2p programs and a few hosts consume most of bandwith. when we limit each flow it does not work as one client has many connection at same time. Firstly I tried to write a script that use the ipfm(which accounts traffic usage) logs as follow .extract ip addresses heavy bandwith users from

Hi all. Here''s the situation Linux box with eth0 connected to LAN, and eth1 connected to internet via cablemodem. Connected to the lan are some voip devices, ive configured htb in eth1 to save some bandwith for the voip devices. Now i have another issue, at some hours of the days, some servers in the lan downloads data from other servers in internet and they use all bandwith available.

hi, (assume HTB) I was thinking will it be possible to do some sort of UNFAIR-SHARING :"), what I have in mind : Say I have a internet link with 100kbits bandwith, then I want to share it between many clients (which will increase over time). Let''s i start with 5 clients with rate = 30kbits... See the total bandwith of users is 120kbits but I have only 100kbits.... So where is the

Hello all. We have three tunnels over the internet between our "central" gateway and some branch office gateway. Each gateway has eth0 on its LAN an eth1 on the internet. We use DSL lines and eth1''s have the internet IP directly attached on it. Each gateway, also, acts as iptables NAT gateway. The outgoing bandwith is 300 kbit, and we tried this (i.e.) on each tunnel: tc

Hi All, Leo here''s the information: Having being bombarded for not providing a link, i guess its time. Actually wanted to see the response first, we would like interested parties we can communicate too in other to get updates on how the code is performing. Please if your interested or you know someone that is, send a mail to <alexander.clouter@connectfree.co.uk>,

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I''m absolutely new to tc and found The Ultimate Traffic Conditioner to be exactly what I wanted as a starting point. Now the script doesn''t behave as I expected though, which applies to both the CBQ and HTB versions, the latter of which being my preference. The only changes made to the script are these assignments:

Hi, I''ve a small question about the cbq.init script. For a gateway I want to shape connections from special IP addresses to limit their bandwith. In my test environment I''ve too machines. One testclient with the IP 192.168.1.19. On my "shaper" (192.168.1.251) runs cbq.init with following config file: orthanc:/etc/sysconfig/cbq# cat cbq-4.ws-019

Hi, It is exactly what I need except one thing. I don''t know exactly if my router is the right place to apply QoS policy. It has two network interfaces and both are 10Mbit/s. The slow part of the network is little bit more far. On their QoS we have 2Mbit and I want all our users to divide this bandwidth equally but also don''t want to unnecessarily restrain their bandwith and to

Hello Everyone, i''m having problem in limiting bandwith on my external interface in the server. i''m having a network here which is online via a linux server with cbq compiled in kernel. i''m having eth0 as internal network card, eth 1 as external network card my internet bandwith line is 8kbps on eth1 i want to limit this 8kbps to 4kbps at eth1 and no shaping on

hello again, I got some just preliminary results .... hope someone can explain them to me... As I already told I have the following config : egress { class (30kbps) {sfq}; class (50kbps) {sfq}; class (80kbps) {sfq}; class (30kbps) {sfq}; class (50kbps) {sfq}; ...hundreds like this... class (10kbps,default) {sfq}; } What I got is traffic starvation very often for a period of ~30 sec.. as

I recently suffer badly from low bandwith. At first I thought it was my Linux box, but after tracing the problem it turns out it was the ammount of double posts I get from Patrick Turley... :) Isn''t there a way to block mail.rocksteady.com? It seems the mail originates from 10.50.23.3, and is forwarded by this host (which would make sense). Greetz -- Jurrie

Hi all, i have a problem: i have an adsl modem that is connected to internet. I can''t manage this modem. Between my PC and the modem i have a linux firewall that make the NAT and the traffic shapping. I have create a script that limit the bandwidth of the "external" interface of the firewall so i can manage my bandwidth for my internet application. The problem is that i need to

Hi, I am the network administrator of my company, I know quite well Windows networking and a few about Linux and its amazing routing and QOS capabilities. Right now, we have a bustable T1, which mean that the bill increase with out T1 use. I have decided to find a way to shape the traffic so I can stay at a raisonable speed of 256 kb/s (Up/down) on my T1. I have linux gateway with 2 nics behind a