similar to: Wan Simulation / Bw/Latency testing

Hi all, I have one bridge system (used for controlling bandwidth) connected to three different DSL ISP provider. I have the following setup below: - +-------------+ | br0 | | -> eth1 | -> DSL_1 | -> eth2 | +-------------+ | br1 | | -> eth3 | -> DSL_2 | -> eth4 | +-------------+ | br2 | | -> eth5

Hello newsgroup, I hope somebody with more routing experience then me can help me with the problem I have. The setup is as described below. A dual internet provider routing, multiple local area networks, and a dmz network with one public and one private ip range. I followed the instructions at lartc.org, and so far everything is working. The default route is via

I have a setup with two Internet providers. One circuit (net0 == eth1) is used primarily for employees and tunnels to other sites. The other (net1 == eth2) is for the production machines that customers access. Everythung works in teh sense that packets get to where they are sent (mostly) but I recently I had a sniffer on the system and noticed a problem I cannot solve. traffic coming in

Hi, Shorewall version -4.0.12-2 (EL5 rpm version) OS : Centos 5.2 I have shorewall successfully running on Linux with multi ISP. Trying to make services such as "rsync, ftp" go through my secondary ISP. For which I did the following eth0 : Internal LAN eth4 : DSL (Second ISP) => x.x eth5 : T1 (First ISP) => y.y Created the following entries in

Hi, I met a problem when using bridge with netfilter. The kernel version 2.4.20, and the patch is bridge-nf-0.0.10-against-2.4.20.diff. Our firewall configuration is as follows, eth3,eth4,eth5,eth6 configured as a bridge with an IP address 10.0.0.1. The local net connect to the internet via the gateway 10.0.0.1 and SNAT is applied on the firewall. It worked but sometimes there are some

I have been studying Tom''s configuration at: http://www.shorewall.net/myfiles.htm -and- http://www.shorewall.net/NAT.htm I am using SBC as an ISP and also have 5 "real" IP addresses and because of other issues, have to re-do my set-up. If I have a block at .120/29 assigned to me, what SBC does is give you 5 usable addresses, in my case .121 is the SBC modem/router and

All, I've got a machine running CentOS 5.3 and this machine has got 2 - built-in 1 Gig NICs and a expansion card with 4 - 100 Meg NICs. For whatever reason at install time, it made the expansion card eth0 through eth3 and the internal ports eth4 and eth5. And by default the 'machine' is known on the network by the eth0 NIC, so my throughput is limited to 100 Mb. How can I force

Hello all, I am new to Linux Ethernet bridging. Let me first start with what I am trying to achieve. Well you see - I am attempting to have 2 main firewall running at the same time - one as a master and the other one as a slave. Yes, I would like to make use of Ethernet bridging in this scenario - as I understand it, all I need are two machines and STP enabled. I am running Debian

I have a 2.6.12(ubuntu-patchset), kernel recompiled with this routing options: [*] IP: advanced router [*] IP: policy routing [*] IP: equal cost multipath Load balancing is working great, but i have problems whits long term tcp flows (like msn-messenger or vpns or any other type of long term ip based conection). I assume this is because after a period of time, the per-host

I''m having another little problem with my new firewall. I want outgoing port 25 from my mail server to appear on the address 65.223.121.227 so I created the file masq: eth2 192.168.124.18 65.223.121.227 tcp 25 eth1 eth5 eth1 eth3 eth1 eth4 eth1 == net0 == 209.189.103.196/27 eth2 == net1 == 65.223.121.237/28 eth3 == dmz0 eth4 == dmz1 eth5 == loc ==

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello all, I''ve a problem with the configuration below eth3 - Connection to ISP 1 eth4 - Server Farm Public address (202.73.10.*) eth5 - Local Area Network (192.168.0.0/24) I''m doing this one-to-one NAT because there is a server need to have the public ip and it is located in somewhere that can only be reach by LAN. I''ve

Hi, I had successfully setup my bridge (br0) but after few minutes the br0 interface seems not working. ifconfig eth0 0.0.0.0 ifconfig eth5 0.0.0.0 brctl addbr br0 brctl addif br0 eth0 brctl addif br0 eth5 brctl stp br0 on I check on my system's /var/log/syslog file. It shows something strange messages as below: - Jan 2 10:44:22 fw01 kernel: ipt_tcpmss_target: bad length (64 bytes)

Hi i have read the all the docs and try to deploy the load balance and QoS using my 4 links (DSL links) My setup looks like below LAN ----Local IP-----Connected to Linux Box Eth1 Eth5-- connected to one DSL1 Eth4-- connected to one DSL2 Eth3-- connected to one DSL3 Eth2-- connected to one DSL4 iam marking them in prerouting randomly and puting them in table and snating at POSROUTING

Hi, I''ve defined a hash like so in my nodes.pp: net::addr { "eth5": rt => { rt1 => { address => ''192.168.10.0'', netmask => ''255.255.255.0'', gateway => ''192.5.28.19'', src =>

Hi List, I am running into a problem where I have 2 interfaces bridged with and ip address assigned. I have another interface in which traffic has ingress traffic that needs to go out the bridged interface. I am trying unsuccessfully to SNAT the traffic leaving the bridge interface to its assigned address. # brctl show xbrdg0 bridge name bridge id STP enabled interfaces

On Mon, Jul 10, 2023 at 12:20:01PM +0300, Gavin Li wrote: > Currently, coalescing parameters are grouped for all transmit and receive > virtqueues. This patch series add support to set or get the parameters for > a specified virtqueue. > > When the traffic between virtqueues is unbalanced, for example, one virtqueue > is busy and another virtqueue is idle, then it will be very

Hi all, I''m trying to set up a computer with 2 routes to the internet, much as described at http://lartc.org/howto/lartc.rpdb.multiple-links.html .One of my interfaces (eth5, 192.168.2.2) is only used for traffic originating inside the network. The other (eth1, 192.168.1.2) is only used for a VPN, where all (udp) traffic originates from outside our network. I have created a second

On Thu, 13 Jul 2023 07:40:12 -0400, "Michael S. Tsirkin" <mst at redhat.com> wrote: > On Mon, Jul 10, 2023 at 12:20:01PM +0300, Gavin Li wrote: > > Currently, coalescing parameters are grouped for all transmit and receive > > virtqueues. This patch series add support to set or get the parameters for > > a specified virtqueue. > > > > When the

Hello, I''m new to Xen (and this mailing-list) and facing some problems with the network. I''m stuck and don''t know how to continue. And Google isn''t very helpful either... My setup: - Ubuntu 7.10 for dom0 and Debian 4.0 for all domU - 4 physical NIC (DHCP from my ISP, internal LAN, DMZ & WLAN) - 1 Dom as firewall/router - 1 domU with internal services

Hi, The CBQ config file shud be some thing like this. DEVICE=eth0,10Mbit,1Mbit RATE=50Kbit WEIGHT=5Kbit Shall i hardcode the DEVICE BW as 10/100 Mbit or Shall i use any other tool like ethtool for getting this. ethtool gives Speed: 10Mbps If so, how about, if i use some other Interfaces other than eth0, like ppp0 or some other? C''d anybody can give a suggestion over this? thanks