similar to: wondershaper htb + multiple ports

Hi, I have a question conercing wondershaper. I''m using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper. On start up of wshaper, there are no errors or any other problems but I''m not sure if it''s running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

Hi, When i do ''wshaper start'' the interface i have defined stops routing traffic for some reason. It resumes routing when i do ''wshaper stop''. I''m using debian stable (3.0 woody) with debian''s default 2.4.18-686 kernel. When I run the script I get no errors, and when I do a ''status'', everything looks correct. Can ANYONE

Hi, I just installed wondershapper 1.1a on my ipcop firewall box. I have roadrunner cable with a ftp server setup. My download speed is 2mbit (I get 225 KBytes) and my upload is 384kbit (I send at 43 KBytes). What should the settings in wshaper? I can ping yahoo.com at 90msec with little traffic.....and at around 220msec with full upload traffic. Mark

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

I have wondershaper to limit my upload at 400kilobits (my line is 600kbps). I do a lot of torrent seeding and I dont want my pings killed when I''m uploading so I set low prority source ports as follows (by the way, I have bittornet to only use ports 6881-6910): NOPRIOPORTSRC="6881 6882 6883 6884 6885 6886 6887 6888 6889 6890 6891 6892 6893 6894 6895 6896 6897 6898 6899 6900 6901

Season Greetings to all Tom, in your faq, u have this noted: While I am currently using the HTB version of The Wonder Shaper (I just copied wshaper.htb to /etc/shorewall/tcstart and modified it as shown in the Wondershaper README), I treid this with wondershaper, using Bearing Leaf 1.0 stable i even changed the tc command to run_tc, and tried it in both angles, and i receive the following..

I don''t know whether this is the right place to ask, but kindly point me to an FM that I can R if it isn''t. My wife is creating lots of Kazaa traffic, and I am using rsync to create a full mirror of Red Hat''s FTP site, Aurora Linux FTP site, the LDP site, and some other stuff. Clearly, when one is moving well over 100GB over a 128 Kbps link, this is going to take a

Hi all, ive got 2 internet connections set up via the nano howto (which are working great) and we are running NAT. Was looking in to qos mainly to stop large http downloads/ftp downloads from hogging the line so that browsing for other users doesnt slow to a crawl, but if the line is free and no one is doing anything then for it to use the available bandwith. The wondershaper sounded exactly what

Hi, I''m really new to traffic shaping and try to implement the wshaper.htb script. I have a linux box that serves as vdr, mldonkey, samba, apache and mailserver (imap), connected to my LAN with 100mbit. I''m connected to the inet via adsl with a hardware router/firewall, got 384k downlink 64k uplink. When I have mldonkey running, imap (via Outlook) gets *very* slow (mails with

I''m trying to setup traffic shaping on my linux gateway/router. The system has 3 interfaces: eth0 - My LAN - with IP address 192.168.0.254 eth1 - The ethernet connection to which my ADSL modem is connected. This has a 10.25.x.x IP, more on this later. The ADSL link has an upstream of ~1.2mbit. ppp0 - The PPP connection which is my WAN connection, with a real world IP. The system acts

Hi I am very unclear about the wonder shaper and a bit of a novice with Unix all together I have a question for you and I hope you can answer Basically my office is getting a couple of people slowing down the network so ive been looking around and found wondershaper What I want to know is that can I rather than having low priority ports have it with high priority ports And

Hello Thilo, What did you find superior with CBQ-wondershaper over HTB-wondershaper? We have not been using wondershaper specifically but our simple tests so far seem to show that htb is much easier to configure for a given target shape (i.,e accurate) compared to CBQ. Torsten -----Original Message----- From: Thilo Schulz [mailto:arny@ats.s.bawue.de] Sent: Saturday, June 14, 2003 8:55 AM To:

Hello, I am trying wondershaper-1.1a on a friend''s pppoe connection on her Linux box. There are a few things I don''t understand. 1. She has pppoe connection so should DEV=eth0 or DEV=ppp0 ? 2. Her ISP just says on her payment bill that the speed is 128kbps, but doesn''t mention any downlink/uplink speed, so in that case what should be, DOWNLINK= and UPLINK= ? 3. She

Hi Guys, I''m asking this question again because I have exhausted resources for understanding how to get it to work. I''ve read the howto on getting traffic shaping to work (shorewall''s web site) as well as trying out wondershaper''s htb and cbq scripts. Somehow both does not seem to happen as I want it to. I''ve also read through the lartc

greetings all, i''ve searched high and low for this, but can''t seem to find an answer anywhere.. having read the docs and the wondershaper script itself, it occurred to me that the documentation promises an immediate drop in interactive app latency, specifically mentioning SSH as a big winner. however, looking through the script i can''t really tell just *how*

Sir, Thanks for the wondershaper utility! It has improved the response time for my ssh connections to my home server whenever i need to access it from the Internet. However, is there a way to setup a bandwidth, say 10kbits/sec (i only have 128kbits/sec DSL), and assign it to a particular traffic type like kazaa and other P2P file-sharing? This way it will guarantee that my home users of

Hi I''m looking for a quick recipe for a newbie to control http traffic in my linux gw. My internet is overloaded already and vpn external clients are experiencing troubles (disconnecting in peak hours). Any suggestions ? Regards Guillermo Caracas/Venezuela On Thu, 2004-05-06 at 14:40, lartc-request@mailman.ds9a.nl wrote: > Send LARTC mailing list submissions to >

Hi all, I moved wshaper 1.1 cbq file to tcstart, but none of my tcrules are being observed. The only way I can set the marks is by editing the tcstart file. Is there a way to incorporate for tcstart to read and apply my set marks in tcrules? Thank you, ~Andrew Nady.

I have packet shaping set up with "The Wonder Shaper" tcstart file. I thoroughly tested upload and download performance with bittorrent and the following config was the best: DOWNLINK=425 UPLINK=3450 DEV=ath0 The main problem is that browsing is sluggish, but ssh is a bit sluggish too. Bittorrent performance is great though. My bittorrent client is set to listen on port 6881 so I