similar to: wondershaper htb

Is there a way to apply wondershaper w/ htb to a port range? I have a ftp server on port 65432 and passive ports 50000-60000. Is there a way to set a range? or do they have to be individually listed? The following doesnt seem to work: # low priority source ports NOPRIOPORTSRC=65432, 50000:60000 # low priority destination ports NOPRIOPORTDST= Mark

I have wondershaper to limit my upload at 400kilobits (my line is 600kbps). I do a lot of torrent seeding and I dont want my pings killed when I''m uploading so I set low prority source ports as follows (by the way, I have bittornet to only use ports 6881-6910): NOPRIOPORTSRC="6881 6882 6883 6884 6885 6886 6887 6888 6889 6890 6891 6892 6893 6894 6895 6896 6897 6898 6899 6900 6901

Hello Thilo, What did you find superior with CBQ-wondershaper over HTB-wondershaper? We have not been using wondershaper specifically but our simple tests so far seem to show that htb is much easier to configure for a given target shape (i.,e accurate) compared to CBQ. Torsten -----Original Message----- From: Thilo Schulz [mailto:arny@ats.s.bawue.de] Sent: Saturday, June 14, 2003 8:55 AM To:

Hi, I just installed wondershapper 1.1a on my ipcop firewall box. I have roadrunner cable with a ftp server setup. My download speed is 2mbit (I get 225 KBytes) and my upload is 384kbit (I send at 43 KBytes). What should the settings in wshaper? I can ping yahoo.com at 90msec with little traffic.....and at around 220msec with full upload traffic. Mark

Hi, I have a question conercing wondershaper. I''m using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper. On start up of wshaper, there are no errors or any other problems but I''m not sure if it''s running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I

Hi there! It just occured to me that there is a difference between wshaper and wshaper.htb. In wshaper there is no check on the ACK-bit, all small packages are priorized. Is that the new way to go, or is it a "bug"? Greetings, Nils _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

hi there, this is my 1st message in the list. I would like to use this wondershaper.htb to limit the bandwith usage at home. My kernel config is: # QoS and/or fair queueing # CONFIG_NET_SCHED=y CONFIG_NET_SCH_CBQ=y CONFIG_NET_SCH_HTB=y CONFIG_NET_SCH_CSZ=y CONFIG_NET_SCH_HFSC=y CONFIG_NET_SCH_PRIO=y CONFIG_NET_SCH_RED=y CONFIG_NET_SCH_SFQ=y CONFIG_NET_SCH_TEQL=y CONFIG_NET_SCH_TBF=y

Hi, I have tried unsuccesfully to limit my ftp server send speed in linux. I have an ipcop linux firewall/router with 2 nics. 1 nic (eth1) is connected to a 3mbit/384Kbit cable connection and the other (eth0) a switch. Behind it i have a suse linux box and a windows box. On the suse box i run proftpd. I need to shape my passive ftp send speed to 34KBytes because if it is maxed out at 45K

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

Hi, first of all, let me thank you for your great Shoreline Firewall. I use it with great success at home (protecting my WiFi connection). And now if I could have a question about traffic shaping. I did read everything I could find but I still have two problems: first, the MARK from tcrules is not working in HTB based simple tc filter line ("handle $MARK fw classid 1:20"). If I switch

Season Greetings to all Tom, in your faq, u have this noted: While I am currently using the HTB version of The Wonder Shaper (I just copied wshaper.htb to /etc/shorewall/tcstart and modified it as shown in the Wondershaper README), I treid this with wondershaper, using Bearing Leaf 1.0 stable i even changed the tc command to run_tc, and tried it in both angles, and i receive the following..

Hi Guys, I''m asking this question again because I have exhausted resources for understanding how to get it to work. I''ve read the howto on getting traffic shaping to work (shorewall''s web site) as well as trying out wondershaper''s htb and cbq scripts. Somehow both does not seem to happen as I want it to. I''ve also read through the lartc

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

Hi I''m actually using a wondershaper derived script. The problem I have is that when I ping (ping is in high priority queue) the ping time is not as low as I expected with p2p running: 760 packets transmitted, 760 received, 0% packet loss, time 759695ms rtt min/avg/max/mdev = 39.667/62.863/598.539/33.287 ms, pipe 2 With voip, it is much better with the qos but it is still a little

Hullo :) I appear to be having a common problem, but the standard fix hasn''t worked for me :/ I''m using a 2.4.23 kernel, with QoS options thusly: # QoS and/or fair queueing # CONFIG_NET_SCHED=y # CONFIG_NET_SCH_CBQ is not set CONFIG_NET_SCH_HTB=m # CONFIG_NET_SCH_CSZ is not set CONFIG_NET_SCH_PRIO=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m

I''m having a network inside of a dsl modem and I''m using wondershaper on the computers to be able to surf while bulk downloading. The problem is that also the internal traffic is shaped, which means the internal network is at 200kb/s, instead of 100Mb/s. Is there a way to exclude the internal adresses from the wondershaper rules, or is there any other good way to solve this?

Hi ! I´ve been using the wonderful wondershaper from chapter 15.8 of the LARTC Howto for some time. It´s really wonderful. Actually, I use the version from http://freshmeat.net/projects/wshaper/?topic_id=87 Now I tried to put some hosts to low priority, and it doesn´t work. The traffic is splitted equally between the noprio and the other hosts. Is this because I use ip masquerading, and all

Sir, Thanks for the wondershaper utility! It has improved the response time for my ssh connections to my home server whenever i need to access it from the Internet. However, is there a way to setup a bandwidth, say 10kbits/sec (i only have 128kbits/sec DSL), and assign it to a particular traffic type like kazaa and other P2P file-sharing? This way it will guarantee that my home users of

Hi, I am using the following script to limit my outbound traffic. This scipt runs on a box behind my firewall. It limits my outbound passive ftp traffic to 39K perfectly....just like i want. However, i just noticed that it is also limiting uploads coming to my server. Is there something I can change to make it not limit uploads to my server? #!/bin/bash #shaping passive ftp traffic # mark the

Hello everyone. I''ve been trying to get Qos to work here for two days now, but it REALLY doesn''t seem to work the way I want to. Here is my situation: Internet Wireless LAN Firewall DMZ Local lan As you can see, I got a Debian box in the middle as my firewall with 3 network interfaces and a wireless one. I use