similar to: Problems with HTB (ceil being overpassed)

With the below script, whenever I ping 10.0.16.10 (which matches the only filter I have), traffic still get''s sent to the default 1:2 class instead of 1:1 and I don''t know why... Any hints? (kernel 2.6.12, iproute2-2.6.15) tc qdisc del dev eth0 root > /dev/null 2>&1 tc qdisc add dev eth0 handle 1: root htb default 2 tc class add dev eth0 classid 1:1 parent 1: htb rate

Hello, i have a htb setup where the root and (nearly) all child classes has a ceil rate with max up from my adsl line. But the root class don''t reach the ceil value but some childs are get a huge backlog. My setup: (tc -d class show dev ppp0) [cleaned a bit] ******************************************************** class htb 1:1 root rate 576000bit ceil 576000bit burst 30Kb/8 cburst

What''s going on here? I''m spewing UDP traffic at this thing, and it is exceeding the ceil. Anyone know how to fix this? class htb 1:613 parent 1:5 leaf 613: prio 6 quantum 2560 rate 20480bit ceil 103360bit burst 15Kb/8 mpu 0b overhead 0b cburst 1728b/8 mpu 0b overhead 0b level 0 Sent 16591370 bytes 4159 pkt (dropped 39449, overlimits 0 requeues 0) rate 412384bit 6pps backlog 0b

A bit more detail. I have the following htb classes set up... class htb 1:356 parent 1:4 leaf 356: prio 4 quantum 1600 rate 12800bit ceil 51680bit burst 15Kb/8 mpu 0b overhead 0b cburst 1663b/8 mpu 0b overhead 0b level 0 class htb 1:357 parent 1:4 leaf 357: prio 4 quantum 1600 rate 12800bit ceil 51680bit burst 15Kb/8 mpu 0b overhead 0b cburst 1663b/8 mpu 0b overhead 0b level 0 class htb 1:2 root

Hello all, when running tc -s -d class show dev eth, the parent class rate and ceil are different to the configuration? his is the first time I have used HTB so I may have made some basic mistakes. Thanks in advance Shaun Output as follows: class htb 1:1 root rate 760Mbit ceil 760Mbit burst 997641b/8 mpu 0b cburst 997641b/8 mpu 0b level 7 Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

Hello, I hope this isn't too off topic, but I'm attempting to set up a Spectralink 8002 Wifi phone with our Asterisk installation, and seem to be running into a brick well (more of a wall than others that have posted their experiences). My problem is that the phone boots, associates with the wireless, grabs an IP (tried static too - same thing), contacts the TFTP server for firmware, then

An earlier exchange about someone seeing the rate larger than the ceiling is posted below. Andy explained the reason for the "above ceiling" rate in Daniel''s output . . . but I just saw an example that doesn''t fit. >> tc output >> class htb 1:14 parent 1:1 leaf 14: prio 1 quantum 3072 rate 256000bit ceil 282000bit burst 1820b/8 mpu 0b overhead 0b

Here is another log from the * server CLI, I reall hope some one can help me out on this one. thanks |SELECT count(*) FROM vicidial_auto_calls where status = 'LIVE' and server_ip='127.0.0.1' and campaign_id = '' and call_time < "" and lead_id != '';| -- VDAD get agent: |0|update of vla table: |127.0.0.1 |UPDATE vicidial_live_agents set

Im using a Linux machine with standard pc hardware with 3 seperate PCI network interfaces to operate as a DiffServ core router using Linux traffic control. The machine is a P4 2.8ghz, 512mb RAM running fedora core 3 with the 2.6.12.3 kernel. All links and network interfaces are full duplex fast ethernet. IP forwarding is enabled in the kernel. All hosts on the network have their time sychronised

Hi, I am trying to setup a shaper for my linux box and I am experiencing some problems. What I am trying to do is priorizing packets on the egress link, therefore I have setup some prio classes etc. The priorizing seem to work but the problem is that the ceil parameter doesnt seem to work on non leafs. This is what stats show: > class htb 1:1 root rate 3000bit ceil 3000bit burst 1602b/8 mpu

Hello, Is there any reason why an IP-phone would pounder on port 5060 ? My firewall blocks the public IP because it thinks the remote IP is port scanning on port 5060. I think the phone is just registering but for some reason it does this repeatedly in a very short time. Oct 28 09:01:48 astserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:00:00

Hi, What exactly are the "tokens"? I thought each token allowed the sending of one byte, that tokens are stored in a bucket that can hold a max of "burst" tokens, and that this bucket is filled with tokens at "rate". But theory does not seem to explain the "tc -s .." output in the examples below. And I can''t figure out why or how... #tc qdisc

Hi, I''m trying to perform some (what I consider) basic traffic shaping on our network utilising HTB. I have mostly reused the example on the lartc.org site: tc qdisc add dev eth0 root handle 1: htb default 10 tc class add dev eth0 parent 1: classid 1:1 htb rate 100mbit burst 24k tc class add dev eth0 parent 1:1 classid 1:10 htb rate 50mbit ceil 80mbit burst 19k tc class add dev eth0

Sorry I pressed the wrong key and sent the message too early... > -----Ursprüngliche Nachricht----- > Von: Philipp Leusmann [mailto:philipp.leusmann@rwth-aachen.de] > Gesendet: Mittwoch, 8. November 2006 12:53 > An: ''lartc@mailman.ds9a.nl'' > Betreff: Why did I need strange ceiling settings? > > Hi all, > > I recently installed traffic shaping on my

Hello! I need to switch from htb2 to htb3, because of speed issues (for me, htb2 is unable to handle more then 100mbit duplex with ~550 classes), kernel profiling shows htb_dequeue_prio at 1st place with 3x isolation. So, I''ve moved from 2.4.19 to 2.4.25 kernel (hi-pac for classification/marking and htb3 for queueing), and traffic rate drop from 100 to 20mbit. What can be wrong? The

If in one time 3 IP adresses using internet. TC script: DEV=eth0 # LAN SERVER_IP=192.168.1.2 # eth0 ip address tc qdisc add dev $DEV root handle 1: htb default 255 tc class add dev $DEV parent 1: classid 1:1 htb rate 384Kbit quantum 1500 tc class add dev $DEV parent 1:1 classid 1:20 htb rate 128Kbit ceil 384Kbit prio 0 quantum 1500 tc class add dev $DEV parent 1:1 classid 1:21 htb rate 128Kbit

Eric, I''ve attached the output from the command you requested below. I''m using kernel 2.6.17.12 and tc version ss060323. I''m have a nforce4 onboard giggabit controller using the forcedeth driver, if that makes a difference. Charlie, I''ll take a look at the Apache model for throttling, thanks. I was going for tc because was going to try to add additional

Hi, I have a server and ten clients in a Gigabit network. The server has 125mbps network bandwidth. I want that the server has 40Mbps bandwidth reserved for client 1 (IP 192.168.5.141), and the rest bandwidth is for all other clients. My script looks like this (I use IFB for incoming traffic): #!/bin/bash export TC="/sbin/tc" $TC qdisc add dev ifb0 root handle 1: htb default 30

Hi All, I am using the script below to limit download rates and manage traffic for a certain IP address and testing the results using iperf. The rate that iperf reports is much higher than the rate I have configured for the HTB qdisc. It''s probably just some newbie trap that''s messing things up but I''m buggered if I can see it. The following script is run on the

Hello, 1. I currently have a 128kbps cable link to the internet..and I''m sharing this connection with others. I''ve made the following script(for alocating bandwidth depending on the services used: browsing, squid, games like counter-strike, icmp, ssh), which unfortunately isn''t working very well as the response times I''m getting upon pinging the server