similar to: HTB and iptables statistics

Hello all. We have three tunnels over the internet between our "central" gateway and some branch office gateway. Each gateway has eth0 on its LAN an eth1 on the internet. We use DSL lines and eth1''s have the internet IP directly attached on it. Each gateway, also, acts as iptables NAT gateway. The outgoing bandwith is 300 kbit, and we tried this (i.e.) on each tunnel: tc

Hi all, I have been getting some strange results with HTB in kernel 2.6.11, and was wondering if anybody could give me some advice. Also, if someone could direct me to the changelog for the recent versions so I can see if it is worth upgrading? Anyway, the problem can best be summed up by looking at the output of ''tc -s -d class show dev eth0''. Some of the relevant results

In this simple htb setup: # tc -s -d class ls dev eth0 class htb 1:1 root rate 300000bit ceil 300000bit burst 1749b/8 mpu 0b overhead 0b cburst 1749b/8 mpu 0b overhead 0b level 7 Sent 13171835 bytes 13169 pkt (dropped 0, overlimits 0 requeues 0) rate 45848bit 10pps backlog 0b 0p requeues 0 lended: 5272 borrowed: 0 giants: 0 tokens: -84429 ctokens: -84429 class htb 1:2 parent 1:1 prio 0

My hardware is a Linksys AP with MIPS 300MHz and Linux kernel 2.4.20. The traffics are from two LAN switch ports to WAN port. And the traffics are generate at a rate of 80Mbit. So the total traffic to WAN port is 160Mbit. The shaping works well that the traffic to WAN port is about 50/30Mbit according to configuration. But the priority seems strange when the root rate is 50Mbit. When the root

Hello, i have a htb setup where the root and (nearly) all child classes has a ceil rate with max up from my adsl line. But the root class don''t reach the ceil value but some childs are get a huge backlog. My setup: (tc -d class show dev ppp0) [cleaned a bit] ******************************************************** class htb 1:1 root rate 576000bit ceil 576000bit burst 30Kb/8 cburst

Thanks for quick reply Andreas! > Every class is allowed to use bandwidth as long as it does not have to > borrow (the specified rate is guaranteed). Prio in HTB only affects > borrowing bandwidth from other classes... In the example below, the class > 1:5 should be allowed to borrow bandwidth before 1:14 does. Thats exactly what I want from HTB to do..to prio the borrowed bandwidth.

Here goes the filter statements: #Initializing traffic control... tc qdisc add dev br0 root handle 1:0 htb #Loading queue disciplines for plis230 network... tc class add dev br0 parent 1:0 classid 1:1 htb rate 512kbit ceil 512kbit #Loading queue disciplines for pmad048 network... tc class add dev br0 parent 1:1 classid 1:20 htb rate 30kbit ceil 30kbit #server queue tc class add dev br0 parent

Hi, got a 25/25Mbit connection which is quite stuffed. So I applied htb rules. Uplink: class htb 1:1 root rate 24500Kbit ceil 24500Kbit burst 4661b/8 mpu 0b overhead 0b cburst 4661b/8 mpu 0b overhead 0b level 7 Sent 430600689269 bytes 730147320 pkt (dropped 0, overlimits 0 requeues 0) rate 23057Kbit 5520pps backlog 0b 0p requeues 0 lended: 199673949 borrowed: 0 giants: 0 tokens: -964

Hello all, when running tc -s -d class show dev eth, the parent class rate and ceil are different to the configuration? his is the first time I have used HTB so I may have made some basic mistakes. Thanks in advance Shaun Output as follows: class htb 1:1 root rate 760Mbit ceil 760Mbit burst 997641b/8 mpu 0b cburst 997641b/8 mpu 0b level 7 Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

Hi I have setup iproute2 and need a bit of help reading the stats from it ===== output qdisc htb 1: r2q 10 default 20 direct_packets_stat 0 ver 3.17 Sent 547326809 bytes 1342627 pkts (dropped 9303, overlimits 2817572 requeues 0) backlog 46p qdisc sfq 10: limit 128p quantum 1514b flows 128/1024 perturb 10sec Sent 41874343 bytes 730889 pkts (dropped 0, overlimits 0 requeues 0) qdisc sfq

Hi, I''m using tc and HTB to shape my outgoing ADSL traffic. I was trying to make some graphs on the classes by meassuring the "sent bytes" of each class using rrdtool to store the data (as kbps after conversion). I expected that meassuring the root class I would get values similar that the ones I get measuring the interface counters but they differ by a large amount. Is

Hi I have tested with FC3 but iam not able get any good results on that. in the list some one recomend me that > 3.17 HTB should work I saw latest FC4 test2 has the HTB 3.17 with iptables 1.3.0 i have install in my P4 box, and trying to test when iam uploading its working perfect, but when iam downloading its going to default class can some one experinced the same problem below is the my

tc qdisc add dev eth0 root handle 1: htb default 12 tc class add dev eth0 parent 1: classid 1:10 rate 30kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1: classid 1:11 rate 10kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1: classid 1:12 rate 60kbps ceil 100kbps burst 2k tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip src 172.16.11.2 flowid 1:10 i login

Hello, I use HTB with linux-2.4.20-ac1 and iptables-1.2.7a (pathced for IMQ). I configured one HTB qdisc on an IMQ device. This qdisc has some classes (about 5) and all of the classes has qdisc pfifo. I sometimes got out from my linux (while I was working) and I found in logs: Dec 4 11:49:27 core kernel: HTB init, kernel part version 3.7 Dec 4 11:49:28 core kernel: HTB: quantum of class

Hi all, I''m trying to setup htb on a box with the following class configuration: class htb 1:2 root rate 4Mbit ceil 4Mbit burst 2099b/8 mpu 0b overhead 0b cburst 2099b/8 mpu 0b overhead 0b level 7 Sent 0 bytes 0 pkts (dropped 0, overlimits 0 requeues 0) lended: 0 borrowed: 0 giants: 0 tokens: 4300 ctokens: 4300 class htb 1:4 parent 1:2 leaf 4: prio 7 quantum 1000 rate 1Kbit ceil

Hi. I did send this to `jaazz@post.cz'', but I suspect the list is a more appropriate/useful place for it. It''s a question about Michal Charvat''s QoS extension to Net-SNMP. When I look at the MIB entries for the QoS handles, I get something like this - enterprises.qos.qosObjectTable.qosObject.qosHandle.0.0 = Gauge32: 0

I''m attempting to set up a hierarchy of tc qdiscs with filters, but the filters don''t seem to be working correctly.  I''m running iptables 1.3.5 with iproute 2.6.16.20060323 on a Gentoo 2.6.18 kernel.  The system takes all my tc setup, but does not filter packets as I am expecting it to based on my ruleset. My tc qdiscs and classes are added correctly and report as

Eric, I''ve attached the output from the command you requested below. I''m using kernel 2.6.17.12 and tc version ss060323. I''m have a nforce4 onboard giggabit controller using the forcedeth driver, if that makes a difference. Charlie, I''ll take a look at the Apache model for throttling, thanks. I was going for tc because was going to try to add additional

Dear all, First, sorry for my bad English .. To night one of my client is the victim of UDP attack from internet. It''s tons of UDP packets from internet with destination to port 80. But when I look at class of that victim client, the actual class rate is over than configured rate class. Below is my screen capture. You can see at class 1:913 which have actual rate 105136bit while

Hi, I''ve have my IP and TC scripts working OK but my rate limiting does not seem to be being appiled. My available download speed is around 150kbps. I''d like to limit this box and the machines it forwards for to 10kbps each, a total of 20kbps. Thus leaving 130kbps unused. The classes I''ve created are simple and the stats show they are moving bytes OK, however; the