similar to: borrowing

Hello, 1. I currently have a 128kbps cable link to the internet..and I''m sharing this connection with others. I''ve made the following script(for alocating bandwidth depending on the services used: browsing, squid, games like counter-strike, icmp, ssh), which unfortunately isn''t working very well as the response times I''m getting upon pinging the server

Hi everyone, My HTB script is showing me those "r2q change" warnings. I read that I should test with r2q values to gain accuracy and stop the warnings but I made some tests with r2q and with burst and I still get the warnings. Any ideas on this issue will be very helpful. The script seems to be working as the bandwidth for the IPs is being shaped. The NIC works at 100mbit and the

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

Hi,All I am using iproute2 to manage bandwith for ADSL router.High,medium,low priority are needed for different protocol port on the ADSL's upstream side,as following: LAN --- |ADSL Router|------WAN When there aren't traffic on the specific priority, its bandwidth should be borrowed by other priorities.But it doesn't work.Here is my script: /usr/sbin/tc qdisc del dev nas0 root

Hi, I''m fighting seriously with a most simple HTB setup. I''d like to share the incoming 64kbps into 5 and 59 for two different machines under NAT. HTB seems to hold the required limits when ceil is not set (no borrowing), but when borrowing enabled it seems to share equally rather then keeping the specified ratio. My setup is below. A typical output of "tc -s -d qdisc

This is one of my test classes: class htb 1:10 parent 1:1 prio 0 quantum 2048 rate 160Kbit ceil 400Kbit burst 1803b/8 mpu 0b cburst 2111b/8 mpu 0b level 0 Q1: where does "level 0" stand for? Q2: where does this b/8 stand for? Q3: this is on a i386 platform, so timer resolution should be 10mS. According to the doc the minimal burst should be 10mS*160Kbit=1600. Why is it 1803? Q4: I

Hi, I have a problem with ''tc filter'' on a 2.4.22 kernel from Slackware 9.1 distribution. The tc command binary is from htb3.6-020525.tgz (http://luxik.cdi.cz/~devik/qos/htb) I''m trying the following command sequence: tc qdisc add dev eth0 root handle 1: htb default 1 r2q 1 tc class add dev eth0 parent 1: classid 1:1 htb rate 1200kbit ceil 1200kbit tc class add dev

Hi, I have a parent class 1:1 with rate=ceil=64kbit i create 3 classes under it(1:1). class 1:2 rate=ceil=32kbit class 1:3 rate=ceil=16kbit class 1:4 rate=ceil=16kbit if 64kbit traffic is flowing from the cable all the 3 classes will get their respective shape. 1 .if only 32kbit data is flowing(for some reason). a. Then how will the traffic gets distributed.? b. Is it in first come first serve

Hello... I have one 2Mbit WAN interfaces and two vlan LAN interfaces - vlan2 and vlan3. I''d like to limit bandwidth something like this: rate 1Mbit ceil 2Mbit for vlan2 and rate 1Mbit ceil 2Mbit for vlan3 with possibility to borrow bandwidth between vlan2 and vlan3. ^^^^^^^^^^^^^^^^^^^ Is it possible to do in any way? regards, -- Michal

Martin Devera wrote: > If you read the manual, the algorithm will not work correctly > with {,c}burst < MTU ... > devik > I just tried to change {,c}burst to 1600, or leaving them by default but no visible result. here is the latest tc -s -d class show dev eth0 class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level

This is my first attempt at understanding lartc: I want to throttle outgoing bandwidth fo a certain tcp port and leave other traffic the way it was. so I put a prio qdisc at the root of eth0 (dummy priomap since i want to use filters to switch bands): $ tc qdisc add dev eth0 root handle 1: prio bands 2 priomap 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 then attach a tbf qdisc at 1:2 : $ tc qdisc add dev

Hi, I can''t get traffic shaping working. This is my situation: -------- ------ Net1 ----- |router| -------------------- | TC | ----------- Net2 -------- leased line ------ eth1 eth0 We use the leased line for normal traffic but also for synchronisation between 2 servers. The leased line is 2mbit. The synchronisation

Hi, One more of those ... 1) what is a ctoken with regard to HTB? Does the ''c'' stand for ceil and if so how is it different from tokens? 2) Is the difference, only in the generation of these tokens? 3) Would the ctokens and token be treated equally once borrowed? Kindly help. Thank you. Regards, suraj. __________________________________ Do you Yahoo!? Protect your

Hello. The problems are: 1. Using HTB I get negative values for tokens and ctokens in tc -s output, for example: mich:~# tc -s -d class show dev eth0 class htb 1:11 parent 1:1 prio 1 quantum 1024 rate 8Kbit ceil 23Kbit burst 1609b/8 mpu 0b cburst 1628b/8 mpu 0b level 0 Sent 0 bytes 0 pkts (dropped 0, overlimits 0) lended: 0 borrowed: 0 giants: 0 tokens: 1287999 ctokens: 453286 class htb 1:1

>Hi everyone, and thanks for your help so far. > >I have been playing around with tc and htb for a couple of weeks now, and >while I am nowhere near understanding everything here, I am beginning to >know more about packets than I ever wanted to know. > >I have two university buildings with a 1mb connection to the Internet. The >two buildings (on either side of town) are

Hi ; MY script: tc-htb3 qdisc del dev eth2 root ipchains -F tc-htb3 qdisc add dev eth2 root handle 10: htb default 20 r2q 40 tc-htb3 class add dev eth2 parent 10: classid 10:1 htb rate 50Mbit burst 2000 tc-htb3 class add dev eth2 parent 10:1 classid 10:100 htb rate 12mbit ceil 50mbit prio 1 tc-htb3 class add dev eth2 parent 10:1 classid 10:20 htb rate 38mbit ceil 50Mbit prio 8 ipchains

tc qdisc add dev eth0 root sfq perturb 10 I want to set perturb to 8 then i used this tc qdisc add dev eth0 root sfq perturb 8 system give me the following message RTNETLINK file exists I delete the rule by this :"tc qdisc del dev eth0 root sfq perturb 10" please tell me how can i delete the rule by another way and where is "RTNETLINK file"

How to do ensure a class not lended and not borrowed each other. I do cburst burst 0b ,but ctokens tokens go to negative! --------------------------------- Do You Yahoo!? "更多惊喜，同样精彩，NetVista A30 热卖" --0-611462377-1048485942=:33792 Content-Type: text/html; charset=gb2312 Content-Transfer-Encoding: 8bit <P>How to do ensure a class not lended and not borrowed each

Dear folks, Here goes my bandwidth manager: INTERNET | |eth0 202.14.41.1 BW.Manager | | | +----eth1----192.168.1.0/24 | +------eth2----192.168.2.0/24 Total incoming bandwidth to eth0 is 1024kbps should be shared to eth1 and eth2, which mean each get 512Kbps and burstable to 1024Kbps if other host is idle. My question is how do i apply HTB to these situation ? As far as i know eth1 and eth2

Hello there, Having made quite a lot of expensive mistakes i have finally clobbered together a script for the users on my network. Have a look at it and please suggest as to how can i limit bandwidth to each ip on this network to about 64Kbits. Trevor -- ( >- GNU/LINUX, It''s all about CHOICE -< ) /~\ __ trevor@clovertechnologies.com __ /~\ | \) / Pre Sales