similar to: burst according to time limit???

I was wondering if there is a queue with which I could have a regular rate limit at some kbits (say 256kbits) for my ethernet stations, but allow burstable sessions with a multiple limit (512 kbits) for a specific time (say 3 minutes). Of course, this is the same with having bursts of some Megabit buckets (measuring bits and not time), but for such big bursts i think it isn''t what i

I am trying to shape a client (somewhat advanced). This is my target: Client is 192.168.2.224. I would like to allow him to download with 500000 bits/sec in general. But, for a specific port(say 22), i would like him to download with 300000 bit/sec only. The problem is that my configuration (maybe wrong) allows him to download with 800000 bit/sec. (500000 generally + 300000 on port 22) I thought

2003-06-28 Bandwidth Study - John Todd (jtodd @loligo.com) Purpose: ------------- To obtain a better chart of actual bandwidth usage per codec as seen "on-the-wire" when using IAX2 trunking between two Asterisk telephony servers. Discussion: ------------- Past threads on the asterisk-dev and asterisk-users lists have indicated that the optimal way to save bandwidth on

Dear folks, Here goes my bandwidth manager: INTERNET | |eth0 202.14.41.1 BW.Manager | | | +----eth1----192.168.1.0/24 | +------eth2----192.168.2.0/24 Total incoming bandwidth to eth0 is 1024kbps should be shared to eth1 and eth2, which mean each get 512Kbps and burstable to 1024Kbps if other host is idle. My question is how do i apply HTB to these situation ? As far as i know eth1 and eth2

--- filters/delay/nbdkit-delay-filter.pod | 4 +- filters/rate/nbdkit-rate-filter.pod | 84 +++++++++ configure.ac | 2 + filters/rate/bucket.h | 62 +++++++ filters/rate/bucket.c | 173 +++++++++++++++++++ filters/rate/rate.c | 235 ++++++++++++++++++++++++++ TODO | 9 +

Dear all, I''d like to ask for help with HTB configuration (after having read some manual pages, FAQs and forum posts). Short version: is there a way to specify infinite burst for HTB? (Infinite amount of data to use the "ceil" rate.) Long version: I have the following small topology: cable modem (uplink to ISB) | <ethernet>

Did anybody have success in setting up xen 3.0.2-2 with a newer kernel than 2.6.16? I ran into the same LVM problems as mentioned before on this list (not being able to lvremove a snapshot). Now I''m trying to get the 2.6.18 running from the fedora repository ( http://hg.et.redhat.com/kernel/linux-2.6-xen-fedora ) but I didn''t have any success so far. The xen hypervisor binary

Hi, I wanted to implement some QOS on my Linux Box with HTB, but after some time spend on the configuration and tests, I still don''t manage to have some correct results. Here are the details : -ROOT 2000 kbits -HIGHPRIO SUBCLASS 50 kbits prio 0 -SUBCLASS1 750 kbits prio 1 -SERVICE1 250 kbits prio 1

Hi. I had to update the BIOS of a Silicon Image 3512A Serial ATA controller. I''m not using RAID. When I run the updater program (updflash.exe), it asks me to choose flash memory from a list, something like: AMD Am29F010B (1 Megabit), AMD Am29LV01B (1 Megabit), etc. How can I find out which is flash memory of the controller? Thanks Marcelo

Hi all, I am notice strange behaviour of samba in our mixed fastEthernet/gigabitEthernet enviroment. First of all let me to describe our situation. We have a samba server running debian unstable with 2.6.3 kernel installed. Server has a gigabit copper connection (tg3 driver) to the 100/1000 Megabit switch (3COM 4228G). Client is a WinXP/Linux workstation connected by ordinary 100 Megabit

Hi Paolo Malfatti, Thanks for your script. It works fine. I get what I expect. THANK you all the way until it comes to an end. FOR the benifit for evryone in the LIST. HERE IS the SCRIPT AGAIN. INTERFAZ_LAN=eth0 FULLBANDWIDTH=256 BANDWIDTH4LAN=64 tc qdisc del root dev $INTERFAZ_LAN tc qdisc add dev $INTERFAZ_LAN root handle 1 htb r2q 4 tc class add dev $INTERFAZ_LAN parent 1: classid 1:2

Hi, I''ve read ADSL-Bandwidth-Management-HOWTO http://www.tldp.org/HOWTO/ADSL-Bandwidth-Management-HOWTO/implementation.htm l#AEN166 and I''ve a doubt from script: [ ... ] # DNS name resolution (small packets) iptables -t mangle -A MYSHAPER-OUT -p udp -j MARK --set-mark 21 [ ... ] That is a bug ? I think that " DNS name resolution (small packets) " is better

I''ve been lurking for a while, trying to figure out this traffic control stuff. We have 3 ADSL modems upstream, with 2, 2, and 1 megabit total bandwidth, 1/4 of it up, 3/4 down. We also have about 200 workstations downstream, connected through wifi. We are presently using tc to create about 200 buckets with HTB and SFQ. It seems like this is too many buckets, since usually only about

Hi, I managed to fix 128kbit for an IP address of 192.168.200.3 as below: - tc qdisc add dev eth3 root handle 1: cbq avpkt 1000 bandwidth 100mbit tc class add dev eth3 parent 1: classid 1:1 cbq rate 128kbit allot 1500 prio 5 bounded isolated tc filter add dev eth3 parent 1: protocol ip prio 16 u32 match ip dst 192.168.200.3 flowid 1:1 tc qdisc add dev eth3 parent 1:1 sfq perturb 10 How can I

I am using Asterisk and A2billing Calling Card Platform and after the 6th call the quality starts to degrade. The way it set up is the user calls into the system then dial out so I have 12 channels being used up but 6 active calls. Here are my specs Asterisk SVN-branch-1.4-r79142 on a i686 running Linux Fedora 6, Pentium 4 Hyper-Threading, 64 bit, 1GB of RAM, 80 GB Sata Drive, bandwidth 4 Mbps

Hi all, First of all, I have spent a lot of time reading up on it. Anyway, I live in a shared accomodation with 2 roommates and a landlord and we share a cable internet connection. It is 2Mbit/400Kbit connection. Sometimes when one of us is downloading a song through Kazaa or a new Linux or FreeBSD iso, the bandwidth gets hogged and other users can't get through. I was trying to configure

I have a policy doubt. Suppose next scenario: I''ve a Internet link (1 Mb upload, and 1 Mb download). That link is maneged with a Linux QoS box (HTB/eSFQ and so on). Suppose that I''ve 50 customers sharing Internet Link, and I must to assign 3 ranges of bandwidth for them. Gold customers: 128 kbits Silver customers: 64 kbits brass customers: 32 kbits Next, I create classes

Hi, On 27/09/12 12:45, renato fringuello wrote: > I took some radios from yp.xml 2 days ago, but today someone (like > http://streaming207.radionomy.com/AngeFM) answers to me : > "The file you requested could not be found" > what's the problem? > They doesn't exist anymore? They are off now and they could be on later? Yes, yp.xml is a snapshot of the streams that

I would like to request that some useful work on networking be MFCed from -CURRENT to -STABLE in time for the release of FreeBSD 6.3. In particular, I'd like to see some of the Netgraph nodes which are new or which have seen extensive development brought in -- ng_nat and ng_car in particular. Bringing in the latest version of ng_nat would allow more flexible in-kernel NAT, while ng_car (which

Hi, we have set up a small project in a school the following way: SITE_A(4 port analog to ip g729)------ADSL_ISP1-------ISP2--------Asterisk-----PSTN Site A has 1 Megabit of bandwith (up 512kilobit down 1 megabit) The asterisk box gets internet service via a wireless antenna. 1 Mbit of up/down bandwith Comments: So far, this means that I will need licenses for the 729. asterisk only supports 20ms