similar to: Bandwith thinking error

Hi, I have a typical configuration for my firewall/gateway box: single network card, with a pppoe connection to the DSL modem. I''m already successfully shaping the uplink (how come that the wondershaper.htb doesn''t use the ceil parameter? It should implement bandwidth borrowing!) but i found the ingress policy a little bit rough. I''d like to keep the traffic categories

I have wondershaper to limit my upload at 400kilobits (my line is 600kbps). I do a lot of torrent seeding and I dont want my pings killed when I''m uploading so I set low prority source ports as follows (by the way, I have bittornet to only use ports 6881-6910): NOPRIOPORTSRC="6881 6882 6883 6884 6885 6886 6887 6888 6889 6890 6891 6892 6893 6894 6895 6896 6897 6898 6899 6900 6901

Hello everyone, I want an opinion from people who tryed different matching modules to match diferent types of traffic, especially p2p ones. I would like to hear which scales better as CPU usage and latency : ipp2p, iptables-p2p or l7-filter with the p2p patterns. I want to use one of them to block most of p2p (except maybe dc++ and emule which i want to shape). I would use the matching rules in

Hey, one more question for ipp2p iptables -t mangle -A DSL-IN -p tcp -m ipp2p --ipp2p -j CONNMARK --restore-mark iptables -t mangle -A DSL-IN -p tcp -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A DSL-IN -p tcp -m ipp2p --ipp2p -j MARK --set-mark 7 iptables -t mangle -A DSL-IN -p tcp -m ipp2p --ipp2p -j CONNMARK --save-mark iptables -t mangle -A DSL-IN -p udp -m ipp2p --ipp2p -j MARK

Im getting into tc. How can I control P2P (peer to peer) traffic??? which filters??? any ideas??? Hugonik

Hello, I''ve been trying to shape the bittorrent traffic (on my external interface, upload), but without luck, for this I''m using layer7 filter right now, but I''ve also tried ipp2p, with the same results, I might say that this is not a problem with this packet classifiers, the problem is with HTB, here''s why. When I open azureus (the bittorrent client I

Hello there, I''m having lots of problems with my setup here. Let me explain: I am network administrator for my university dorm. We are about 300 users, and we have 2 ADSL connections doing load balancing with 300kbits upstream and 2Mbit downstream. The load balancing is working great, we are doing connection tracking so I can mark and hence prioritize interactive traffic and ACKS

Hi all I''m new in this list and i hope to lear and to help if possible. But firt i need help :-( I have this messege in my syslog when my classes and qdiscs goes down. Can any one know what does it mean? Thnx in advance. Yannick Arrimadas Bot Oct 14 16:09:27 pototogorri kernel: HTB init, kernel part version 3.17 Oct 14 16:09:27 pototogorri kernel: Unable to handle kernel paging

Hi.... I''m trying to setup a LAN router with P2P filter but the problem is that can''t "catch" Ares. There is a way to DROP "ares" p2p packets ? I''ve tried with last "ipp2p" snapshot without sucess... I''ve Kernel 2.4.28 iptables 1.3.0 Various Patches from patch-o-matic-ng-20040621 iproute2-ss020116 IMQ Patch Esfq Patch

I''m moving to a new place and my new flatmate wants a router because he likes the cleaness of it all in a non geeky way which I can understand. This means it''s going to be hard for me to pursude him to let me run a computer as a router to act as bandwidth cop. But I don''t fancy trying to use ssh, VNC and games while he''s using WindowsUpdate or p2p. So I need

Hi, I appologise for the bad ettiquite of this, but I have tried looking for some HTB examples that would help me, and am having trouble understanding how the tc filters should work, but I can''t figure out why this isn''t working. I''ve written this script, based upon the ultimate traffic shaper at LARTC, to try and shape for me and my 3 housemates. The idea being to

Hi, When i do ''wshaper start'' the interface i have defined stops routing traffic for some reason. It resumes routing when i do ''wshaper stop''. I''m using debian stable (3.0 woody) with debian''s default 2.4.18-686 kernel. When I run the script I get no errors, and when I do a ''status'', everything looks correct. Can ANYONE

Hi folks. Let''s say I would like to make some bandwidth control on my network using HTB. I have 2 clients: PC1: 192.168.100.2 PC2: 192.168.100.3 Server: 192.168.100.1 This has 2 NIC''s eth1 is local and eth2 is connected to the internet. It could be nice to have a script, where you could specify, how much bandwidth you want for a specific host on a network, like, PC1 has

Hi, I''ve a linux as router nat + firewall (POLICY DROP for INPUT OUTPUT and FORWARD) but, I''ve put next rules for p2p software on FORWARD chain [... snip ... ] iptables -F FORWARD iptables -P FORWARD DROP iptables -A FORWARD -p tcp --dport 80 -j ACCEPT iptables -A FORWARD -p tcp --dport 25 -j ACCEPT [... snip ... ] iptables -A FORWARD -m ipp2p --ipp2p -j ACCEPT iptables -A

Hi guys, I want to priorize traffic comming down from internet on my ppp0 int I want port 80 and 21 (and others ) to have preference over P2P traffic, I don''t want to bann P2P just give to it less prio than other more vital services... does anyone know how to do it or where to read on. Thanks in advance

Greetings, I''ve searched, found ftwall, and some other commercial solutions, but am wondering if anyone on this list has any solutions using a linux firewall to block p2p traffic, more specifically Kazaa. Walter Wickersham _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Hi, I''m really new to traffic shaping and try to implement the wshaper.htb script. I have a linux box that serves as vdr, mldonkey, samba, apache and mailserver (imap), connected to my LAN with 100mbit. I''m connected to the inet via adsl with a hardware router/firewall, got 384k downlink 64k uplink. When I have mldonkey running, imap (via Outlook) gets *very* slow (mails with

Hi all, ive got wondershaper working well with the highest download while maintaing minimal latency but the problem is this: ive got 2 nics in the linux router eth0 and eth1. eth1= internet interface but this is connected to a router say 10.0.0.190, now off that router there are other servers, mail server, domino server etc now if i shape on eth1 ingress and egress using the wondershaper script

Hi. there is a way to MARK udp VOIP (SIP) traffic, in order to put in a highest prio class ? Traffic flow seems start on udp 5060 port, but next both server and client seems jump to a random(?) port. I can''t use CONNMARK because is udp traffic. I only see a pattern for L7 patch in order to SIP traffic identification , but I run 2.4 kernel series . When you patch 2.4 kernel with

Hi, I have a question conercing wondershaper. I''m using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper. On start up of wshaper, there are no errors or any other problems but I''m not sure if it''s running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I