similar to: prerouting does not effect filtering

Hi Is there a way of marking packets by mac address instead of ip or ports using a "tc filter u32 match"? I read somewhere that I could use the offset -8 and -14 to grab the mac addresses but if I use anything lower than -8, for example -9, I get an error. I''m modifying the wondershaper script to cap the download speed by mac address. Any sugestions?

Hello! My system is: Internet ADSL(PPPoE) ---> ppp0 [LINUX server(router)] eth0 ---> LAN Server(router) is running on LINUX Slackware 8.1. I have recompiled a 2.4.22 kernel, enabled all QoS support in the kernel config, including HTB. My ADSL bandwidth is 256Kbit/s for download and 64Kbit/s for upload. I use the following HTB+IPTABLES configuration, because I want to reduce bandwith for

Hi all, Im new to all this, and am still trying to get my head qround some of the concepts of how this all works. Ive read the howto''s, man pages etc. Ive setup packet shaping on my router/server box using HTB and SFQ, but its not working the way i would like. Im after shaping that has "weights" for classes so that a lower priority class will slow down when a higher class

Hi All, I''ve been playing with QOS for a short while now and have worked out how to do what I want using HTB. Great queuing discipline btw. My problem is the tc filters I want to setup aren''t working because iptables is getting to the packets first and mangling the src address. The iptables script I am using is MonMotha''s Firewall 2.3.8 and it includes lots of nice

I am looking for a good htb traffic shaping script to prioritize incoming traffic over outgoing traffic for my machine. I have a 100mbit line, ftp up, backup data comming in, but whenever mirrors starts grabbing it they use all the traffic and the backup data comming in (the important data) drops to like 300kb/sec. I was thinking some script doing sleep 60 [if downstream > 1mb/sec, limit

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

Hello At first I must tell you that I´m a real newbie with Linux (and english as well...) I´m using 2 vlans and shaping works quite well without vlan Now I want to do load balancing at these vlans. Any vlan should get the same minimum/maximum bandwidth of download and use the bandwidth that isn´t used by the other one at the moment. But with vlan the shaping doesn´t work. Can you please tell me

Dear all, I want to make a filter for all IRC-Dalnet traffic, so I want to put all traffic for port 6660, 6661, 6662, 6663, 6664, 6665, 6666, 6667, 6668, 6669, 7000, 7001, 7002, and 8000 to a class. So, I create a TC script as below. I''m sure, it is not effective, and we can write it in simpler. I need help, how to make my script below are simpler. The simpler, the better. Thank you

Hello! I have an internet connection of 64kbps garanteed in a channel of 256kbps. On this connection the metropolitan speed is 10Mbps and in the provider''s network the speed is 100Mbps. I have a few clients behind my linux box and i want to set up some limitations because some of them are using it irrational. I am marking the packets with 0 for internet; 1 for metropolitan 2 for

I''m trying to implement something similar the the diagram in section 9.5.2.1 in the LARTC HOWTO, but must have missed something somewhere :( I''m trying to hack up wondershaper, as it looked like a good place to start.. Here''s where I currently at, but I''ve tried alot of different things, all failing, some worse than others. The end result is to throttle back 126

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

Hi! I have a setup where I want to prefer traffic on one port (for testing purposes I used port 22) my setup is : tc qdisc add dev eth3 root handle 1: htb default 30 tc class add dev eth3 parent 1: classid 1:1 htb rate 96mbit burst 15k tc class add dev eth3 parent 1: classid 1:7 htb rate 2mbit burst 15k tc class add dev eth3 parent 1:1 classid 1:10 htb rate 96mbit burst 15k tc class add dev

I run a small Linux webserver and NAT router from my cable modem at home. Whenever someone starts an http download, all other traffic from my LAN is starved. Bandwidth is not really an issue, but latency is particularly horrible -- pings that usually come back in 20ms can take up to 600ms while the web server is active! I set up QoS (netfilter+iproute2) on the NAT machine in an attempt to give

Dear All! I reach the point that I must ask you what I have to do. I am beginner at traffic shaping and I''m very confused with it. :) Here''s my script that doesn''t do what I want to do with it: tc qdisc del dev eth1 root tc qdisc add dev eth1 root handle 1 htb default 2 r2q 10 tc class add dev eth1 parent 1: classid 1:1 htb rate 300kbit tc class add dev eth1 parent 1:

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

Hi to all I am studying HTB on LARTC how to. I realize a simple configuration on router: tc qdisc add dev eth0 root handle 1: htb default 30 tc class add dev eth0 parent 1: classid 1:1 htb rate 3mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:10 htb rate 2mbit burst 15k tc class add dev eth0 parent 1:1 classid 1:20 htb rate 1mbit burst 15k tc qdisc add dev eth0 parent 1:10 handle 10: sfq

Hi, I want to use inverted matches with tc-filter. I tried to invert the matches with a "!", but this doesn''t seem to be the correct syntax. The following rules don''t work: ---------------------------snip----------------------------------------- $TC filter $ACTION dev $DEV protocol ip parent 1:0 u32 match ip src ${NETWORK[$i]} !match ip dst 192.168.0.0/24 flowid

hello to all i''m trying to set a filter but doesn''t want to work. i''ve set ut the qdiscs and the classes like this : tc qdisc add dev ppp0 root handle 1: htb default 20 tc class add dev ppp0 parent 1: classid 1:1 htb rate 120kbit tc class add dev ppp0 parent 1:1 classid 1:20 htb rate 30kbit ceil 120kbit tc class add dev ppp0 parent 1:1 classid 1:21 htb rate 30kbit ceil

Hey all. I''m trying to set up QoS using the HTB qdisc in a very basic setup, but it the example shown in the howto doesn''t seem to be working. While the packets show up in the correct classes, they appear to be completely ignoring the rates, meaning nothing gets shaped. My setup is that I''ve got a a bunch of machines behind my firewall/router: 1.2.3.1

Hello, I use rrdtool to graph the traffic in the different classes on an interface, eth1. Basically, I use the output from tc -s qdisc ls dev eth1 my tc script (which is only for testing the graphing) looks like this: /sbin/tc qdisc add dev eth1 root handle 1: htb default 20 r2q 1 /sbin/tc class add dev eth1 parent 1: classid 1:1 htb rate 200kbit burst 15k /sbin/tc class add dev eth1 parent