similar to: problem with 2 Mbit egress rate

I''m just-so-fresh to the list, so hello everyone. I''m having a realy hard time with setting up very simple bandwidth management. What I am trying to do is setup a 10Mbit interface to send at only 1920kbit to most of the network (to make sure it hardly ever tops 2mbit). I did succeed with the ingress traffic... With egress however, I get very odd results at different speeds. With

I have a strange problem with VLANs with Xen 3.0.4. I signalled it on Xen-users list, but found no definitive solution to it. I configure VLANs so that they are available in dom0; domUs don''t know that they use VLANs. I use a stock "network-bridge" comming from Xen for setting up networking: #!/bin/bash dir=$(dirname "$0") "$dir/network-bridge"

I upgraded to pre3 a couple hours ago & right now I'm watching my 00:00 backup set absolutely _crawl_. Typically, backups would have been finished somewhere in the 00:10 to 00:30 range, depending how much data changed across 6 machines in the past day. As I write this, the 3rd of 6 machines is (hopefully) just finishing its backup with no more than the usual changes per machine. Whiskey

Hi there, I have two ethernet connections of 2Mbit/s each and I''m trying to add them together to one 4Mbit/s connection but I cannot get more than approximate 1Mbit/s! My setup: I have a LAN (10.2.18.0/24), connected to a larger network (10.0.0.0/8) by two WAN-connections with 2Mbit/s each. On each end I have a Linux router. I first setup the routers to use TEQL with one of the

Hi all! I just started to experiment with bandwidth management using tbf. I have the folowing problems with token understanding: 1) What unit is token? Is "1 token = 1 byte" ? If this is so, then with rate=0.5mbit and HZ=100 the bucket gets filled with 0,64kb (655 tokens) every 10ms? 2) How much tokens are used for one packet (1500)? 3) And token unrelated question. Does

Hello, What''s difference between ingress and egress shaping? When we need to setup ingress shaping(policing) ? Bye

Hi all, Supposedly my router is itself streaming traffic to clients. Is it possible for it to mark its packets before going through dsmark?? I have gone through the examples in iproute2/examples, i noticed that there''s always an ingress and egress of which these are 2 different dev. Is it possible for before ingress and egress be the same dev?? I tried the script below but

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I''ve just discovered that trying to pass traffic from multiple interfaces through the same imq is a Bad Thing(tm). A quick search of "HTB IMQ panic" showed me older posts on this list saying that it''s simply incorrect to pass such traffic through the same imq dev. I''m now back to square one on using the linux

Hi, Can Ingress and Egress can be used in Asterisk, so that Jitter can be calculated...! Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20130821/12427233/attachment.htm>

I''m trying to set up customer egress shaping on concentrator that customers connect to using pptp (which uses pppd). This means customers each have a pppXXX interface when they connect. It''s easy to shape their "down" speed this way, and when they disconnect the interface is gone and thus the shaping rules automatically go away as well. However, shaping their upload

I am successfully running ingress (IMQ) and egress (HTB) shaping on a bridge. Is there any way to combine and share the bandwidth between ingress and egress? Example: I have set up www service for egress at 128 KB and ingress at 256 KB. The shaping on them works fine separately. However, I want to create a single virtual pipe for www traffic and limit both ingress and egress combined to 256 KB.

Hi, Does anybody know how to get the SIP call ID of a "Dial" command? Thanks in advance. Ray -- Want an e-mail address like mine? Get a free e-mail account today at www.mail.com! -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20071008/7f27548e/attachment.htm

Hey all, I've been fighting with this all morning, and I feel like this should be a relatively simple task, but I just can't get it to work. I currently have a very basic asterisk v11.6 setup with a single extension (a Bria softphone) and a single sip trunk to my carrier. What I'm trying to accomplish is simply adding the asterisk generated SIPCALLID of the leg between asterisk and

I have two interfaces, eth0 and eth1 but i can''t discern the egress traffic than ingress traffic. I need to apply htb qdisc in both directions, and I read that I need the IMQ patch to do this, because in ingress qdisc i can''t apply htb qdisc...but where is the ingress qdisc? affect the traffic that goes from eth0 to eth1 or is for the traffic that goes from eth1 to eth0?

Hi, I've looked around the archives and have spent a while on voip-info.org but not found an answer so forgive me if this is in a FAQ somewhere. We've got several Asterisk servers with E1 cards (some Digium, some Sangoma). We provide non geographic numbers for customers and route calls to their existing phone numbers. Calls come in over the PSTN and into Asterisk. This works perfectly

https://bugzilla.netfilter.org/show_bug.cgi?id=1673 Bug ID: 1673 Summary: bug egress hook virtio interface with VLAN Product: nftables Version: 1.0.x Hardware: All OS: All Status: NEW Severity: normal Priority: P5 Component: kernel Assignee: pablo at netfilter.org

https://bugzilla.netfilter.org/show_bug.cgi?id=1672 Bug ID: 1672 Summary: bug egress hook virtio interface with VLAN Product: nftables Version: 1.0.x Hardware: All OS: other Status: NEW Severity: normal Priority: P5 Component: kernel Assignee: pablo at netfilter.org

Hi, I have a Debian based NAT router. How can I manage upstream egress bandwidth based on the LAN ipadress in the network below? My goal is that host1 get a minumum of 10Mbit up/down and host2 gets a minimum of 90Mbit up/down, both max 100Mbit up/down? targethost 172.16.255.254 | | 172.16.0.1 natrouter

Hello, After reading the excellent HOWTO I got traffic shaping working nicely over ethernet devices on a test setup. I can''t put this setup live though, because our main firewall has three 2mbit hdlc interfaces instead of a single device. We are using multipath routing using iproute2 nexthop at the moment, and that works fine for firewalling. But now I have a need for shaping and

As the issue concerns both the -user (configuration) and -devel (OOPS), I''m sending this message to both lists. Some time ago I complained about two problems: - VLANs are not working on machines with 100 Mbit cards - I get a kernel Oops (sometimes panic) when I try to use bonding and VLANs with Xen The root of the issue is the same in both cases: VLAN interfaces must *not* be