similar to: Wondershaper stops limiting outbound traffic

Hi, I have a question conercing wondershaper. I''m using the Clarkconnect linux distribution for my linux router and I tried to use wondershaper. On start up of wshaper, there are no errors or any other problems but I''m not sure if it''s running correctly. Only one qdisc / one class is used and when I start an uplink ftp transfer, my ping time is growing up to 1700ms - I

Hi, When i do ''wshaper start'' the interface i have defined stops routing traffic for some reason. It resumes routing when i do ''wshaper stop''. I''m using debian stable (3.0 woody) with debian''s default 2.4.18-686 kernel. When I run the script I get no errors, and when I do a ''status'', everything looks correct. Can ANYONE

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

I''m trying to shape traffic on a Devil-Linux box. This note was originally sent to their maillist, because the LARTC list appears to have been down for the past few days. My mailbox was just flooded with a half dozen or so confirmation requests in response to my repeated attempts to subscribe to this list. ---------- Forwarded message ---------- From: drew einhorn

Hi, I''m really new to traffic shaping and try to implement the wshaper.htb script. I have a linux box that serves as vdr, mldonkey, samba, apache and mailserver (imap), connected to my LAN with 100mbit. I''m connected to the inet via adsl with a hardware router/firewall, got 384k downlink 64k uplink. When I have mldonkey running, imap (via Outlook) gets *very* slow (mails with

Hello, i´ve installed a Suse 8.1 minimal System with iproute 2.4.7 and iptables, Suse default Kernel 2.4.19. When I start the Wondershaper 1.1a Script I get the following Error: CBQ: "allot" is required to set WRR parameters. /home/skripte/./wshaper: line 72: allot: command not found CBQ: "allot" is required to set WRR parameters. /home/skripte/./wshaper: line 78: allot:

Hi, I just installed wondershapper 1.1a on my ipcop firewall box. I have roadrunner cable with a ftp server setup. My download speed is 2mbit (I get 225 KBytes) and my upload is 384kbit (I send at 43 KBytes). What should the settings in wshaper? I can ping yahoo.com at 90msec with little traffic.....and at around 220msec with full upload traffic. Mark

Hi all, I moved wshaper 1.1 cbq file to tcstart, but none of my tcrules are being observed. The only way I can set the marks is by editing the tcstart file. Is there a way to incorporate for tcstart to read and apply my set marks in tcrules? Thank you, ~Andrew Nady.

Is there a way to apply wondershaper w/ htb to a port range? I have a ftp server on port 65432 and passive ports 50000-60000. Is there a way to set a range? or do they have to be individually listed? The following doesnt seem to work: # low priority source ports NOPRIOPORTSRC=65432, 50000:60000 # low priority destination ports NOPRIOPORTDST= Mark

Hi ! I´ve been using the wonderful wondershaper from chapter 15.8 of the LARTC Howto for some time. It´s really wonderful. Actually, I use the version from http://freshmeat.net/projects/wshaper/?topic_id=87 Now I tried to put some hosts to low priority, and it doesn´t work. The traffic is splitted equally between the noprio and the other hosts. Is this because I use ip masquerading, and all

I don''t know whether this is the right place to ask, but kindly point me to an FM that I can R if it isn''t. My wife is creating lots of Kazaa traffic, and I am using rsync to create a full mirror of Red Hat''s FTP site, Aurora Linux FTP site, the LDP site, and some other stuff. Clearly, when one is moving well over 100GB over a 128 Kbps link, this is going to take a

Hi, first of all, let me thank you for your great Shoreline Firewall. I use it with great success at home (protecting my WiFi connection). And now if I could have a question about traffic shaping. I did read everything I could find but I still have two problems: first, the MARK from tcrules is not working in HTB based simple tc filter line ("handle $MARK fw classid 1:20"). If I switch

Hi I''m looking for a quick recipe for a newbie to control http traffic in my linux gw. My internet is overloaded already and vpn external clients are experiencing troubles (disconnecting in peak hours). Any suggestions ? Regards Guillermo Caracas/Venezuela On Thu, 2004-05-06 at 14:40, lartc-request@mailman.ds9a.nl wrote: > Send LARTC mailing list submissions to >

Hi there! It just occured to me that there is a difference between wshaper and wshaper.htb. In wshaper there is no check on the ACK-bit, all small packages are priorized. Is that the new way to go, or is it a "bug"? Greetings, Nils _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

Season Greetings to all Tom, in your faq, u have this noted: While I am currently using the HTB version of The Wonder Shaper (I just copied wshaper.htb to /etc/shorewall/tcstart and modified it as shown in the Wondershaper README), I treid this with wondershaper, using Bearing Leaf 1.0 stable i even changed the tc command to run_tc, and tried it in both angles, and i receive the following..

Hi Guys, I''m asking this question again because I have exhausted resources for understanding how to get it to work. I''ve read the howto on getting traffic shaping to work (shorewall''s web site) as well as trying out wondershaper''s htb and cbq scripts. Somehow both does not seem to happen as I want it to. I''ve also read through the lartc

Hi all, ive got wondershaper working well with the highest download while maintaing minimal latency but the problem is this: ive got 2 nics in the linux router eth0 and eth1. eth1= internet interface but this is connected to a router say 10.0.0.190, now off that router there are other servers, mail server, domino server etc now if i shape on eth1 ingress and egress using the wondershaper script

Hi, I found that I had some thinking error with the wshaper script. I assigned the bandwith of my DSL connection to it, but the machine where it runs is normally connected to the LAN with 100Mbit behind a separate Hardware-Router.Obviously, the complete connection of the machine was slowed down to 384k because I told it so.I guess, since wshaper takes only one card as argument, I can''t

Hi, I really like the wondershaper script, it works very well for me. My question is this. Is there a way to get certain remote hosts to be excluded from the shaping? I ask because I don''t have my box connected directly through the net. It sits behind a nat device, and has ports forwarded in for services. I''d like to limit the ports and services, but only to things going outside

I got wshaper.htb working.....however I have 1 question. How can i limit just ftp server traffic? I have ftp server on port 21 with passive ports of 50000-60000. I currently have wondershaper with htb working on my router....but im afraid that it is also affecting all of my send traffic....not just the ftp server. I want to be able to limit the ftp server traffic only. Thanks, Mark