similar to: tcng and ip_len

Hi all, I have read the larc howto and I need to apply a traffic shaper with this configuration: router / two interface etho and eth1 lan lan is on eth1 and on eth0 I''ve the dsl connection (1.2 Mbit / 256 kbit) I need to limit the bandwith towards lan and I''ve thought at HTB and tcng. I write the script belove. I want limit the p2p and ftp (ssh and irc) connection at 15

Hi, I wanted to configure the following : 1. VPN + some other special connections (TCP 82,8282,23,22 and ICMP) to have priority over the rest 2. special upstream for our updating system on port 4000 3. within the VPN tunnels citrix traffic ( TCP 1494, 2598) + icmp has priority I need this for both incoming and outgoing traffic as it is the bandwith managment config on a central system from

Hi all, Can someone please help with a tcng setup? I have played with tc and tcng in the past, and now would like to get some serious rules in place. However, I have a difficulty in setting them up. My setup is as follows: One machine working as a firewall: eth0 is the interface connected to a 512K DSL line eth1 is connected to a LAN eth2 is connected to another LAN, a bit like a DMZ eth1 and

Hi I''m completely stuck with the tcng language - I assume there must be some way to arrange queues hierachically like eth1 | TBF | PRIO / \ class class but my attempt (below) produces a "inferno.tc:8: qdisc "tbf" has no classes near "prio"" when run through tcc. dev eth1 { egress { tbf (rate 128kbps, burst 64kb,

Hello all, I am trying to set up a simple htb based system, where packets with source ip 10.0.0.1 should have their own class. I plan to use tcng to set it up easier. Is there something wrong in my tcng file ? ~/tcng$ cat htb /* */ #include "fields.tc" #include "ports.tc" dev eth0 { htb ( ) { class ( rate 600kbps, ceil 600kbps ) {

Hey all, i have a class. class ( <$call1> ) if ip_dst == 10.100.1.6 && tcp_dport == 22 if ip_src == 10.100.1.4 && tcp_sport == 22 ; Now when i apply this traffic TO 6 on port 22 is indeed limited to the speed i specify BUT it doesn''t seem to take the src into account at all. If i change the src to anything, even an address that

Newbie here... tcng version 10b I''m just learning about htb and using tcng. I am trying to make the example in Martin A. Brown''s Traffic Control with tcng and HTB HOWTO v0.5 example 2 /* * Simply commented example of a tcng traffic control file. * * Martin A. Brown <mabrown@securepipe.com> * * Example: Using class selection path. * * (If you are reading the

Hello mailing list, i stand bevor a mystery and cannot explain it J. I want to do shaping and prioritization and I have done these following configurations and simulations. I can´t explain, that the combination of PRIO and TBF is much better than the HTB (with the prio parameter) alone or in combination with the SFQ. Here are my example configurations: 2 Traffic Classes http (80 = 0x50) and

Hello. I have been trying to duplicate these u32 matching rules using TCNG, but without much success: tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32\ match ip protocol 6 0xff \ match u8 0x05 0x0f at 0 \ match u16 0x0000 0xffc0 at 2 \ match u8 0x10 0xff at 33 \ flowid 1:10 Wondershaper 1.1a implements this and if I run it things seem to be shaped as expected. But this TCNG

Ok, earlier I post a message explaining my problem with HTB and layer7 (or ipp2p), about not being able to shape the traffic. Well, actually this is what''s happening, I''m marking the packets (right now, I''m using ipp2p as Klaus adviced me to) with iptables, and my queue rules are made using tcng, I''m using the HTB qdisc, and traffic is going to the HTB class

Hey people, I have the following tcng configuration: #include "fields.tc" #include "ports.tc" dev "eth0" { egress { // Voice traffic class (<$voice>) if udp_dport >= 20000 && udp_dport <= 23000; // SSH connections class (<$interactive>) if tcp_dport == PORT_SSH; //

Hi, I have several users on the lanside each allocated separate IP addresses. I need to allocate th traffic to each IP addresses certain portion of total uplink. Say, 192.168.0.2 rate 128kbps, ceil 128kbps. 192.168.0.3 rate 65kbps, ceil 128kbps 129.168.0.4 rate 64kbps, ceil 64kbps. and so on.... Also, for each user i would like to prioritize the traffic within the allocated bandwidth. say for

Hello, I''ve been trying to shape the bittorrent traffic (on my external interface, upload), but without luck, for this I''m using layer7 filter right now, but I''ve also tried ipp2p, with the same results, I might say that this is not a problem with this packet classifiers, the problem is with HTB, here''s why. When I open azureus (the bittorrent client I

My previous message (http://mailman.ds9a.nl/pipermail/lartc/2004q2/012285.html) didn''t generate any replies, so I thought I''d try posting what I''ve done trying to solve my own problem, in hopes that someone will take pity and show me if/where I''m going wrong. Just to recap, I''m trying to accomplish this on my server, which streams RealAudio files

Thank you for your help. It generates this script : tc qdisc add dev eth0 handle 1:0 root htb default 2 tc class add dev eth0 parent 1:0 classid 1:1 htb rate 75000bps ceil \ 75000bps tc class add dev eth0 parent 1:0 classid 1:2 htb rate 125000bps tc filter add dev eth0 parent 1:0 protocol all prio 1 u32 match u32 \ 0xa000001 0xffffffff at 12 classid 1:1 But I thought it was necessary to

I''ve been having a bit of difficulty with a hierarchy of HTBs that I''m wanting to create. Essentially, I''ve got one interface that goes to both the DMZ and the internet. When going to the internet, some of the traffic will be going through a VPN and therefore I want to prioritize it differently, however I want to give the DMZ traffic full speed as long as it

hi, i´am new in tcc (tcng). i try to define my qos for VoIP-Services. For this i wantto define a class for a port range 10000 till 15000. how is the right way? this down works: class (<$voip>) if tcp_sport => 10000 || tcp_sport <= 10000 ; are there any examples of real installations - maybe including VoIP, HTTP and P2P services? regards thorsten gehrig

Hello Mailing list, I have a problem with the prio qdisc and I don´t know what is wrong in my configuration This ist a sample configuration and looks like this: #include "fields.tc" #include "ports.tc" #define X16(i) i i i i i i i i i i i i i i i i dev ppp0 { dsmark { prio(bands 6, priomap X16($be)) { class if ip_proto == IPPROTO_UDP;

This fixes a build failure from undefined references to ASN1_STRING_data in libopusurl.so. ASN1_STRING_data is deprecated in openssl-1.1.0. The new ASN1_STRING_get0_data is identical, except the returned string may not be modified, which we don't do anyway. Also include missing asn1.h header to silence compiler warnings. X-Gentoo-Bug: 592456 X-Gentoo-Bug-URL:

Pulled from Bugtraq. Dan ____________________________________________________________________________ Dan Yocum | Phone: (630) 840-8525 Computing Division OSS/FSS | Fax: (630) 840-6345 .~. L Fermi National Accelerator Lab | email: yocum@fnal.gov /V\ I P.O. Box 500 | WWW: www-oss.fnal.gov/~yocum/ // \\ N Batavia, IL