similar to: IMQ & NAT

Hi! By iptables I set marking (-j MARK) just before -j IMQ. There are only three marks. Exectly all of them are ditected to 1:20 Why I see 3 pkts in default 1:30? How explain it? ### imq0: queueing disciplines qdisc htb 1: r2q 10 default 30 direct_packets_stat 0 Sent 631429 bytes 1812 pkts (dropped 0, overlimits 20) ### imq0: traffic classes class htb 1:20 root prio 0 rate 100Kbit ceil

Hello, I''ve just recently started to use IMQ and I got puzzled after seeing the imq usage example on the linuximq.net site: It was something like this: tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 1mbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 5 tc class add dev imq0 parent 10: classid 10:1 htb rate 256kbit

On my debian woody (kernel 2.4.31) the tcpdump doesn''t work with imq0 devices. If I try to tcpdump imq devices there is no packet seen: [...] rt1:~# tcpdump -n -i imq0 Warning: arptype 65535 not supported by libpcap - falling back to cooked socket tcpdump: WARNING: imq0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on

Hello, I have eth0 - internet eth1..4 - local networks on eth0 i do $IPTABLES -A POSTROUTING -t nat -o eth0 -j MASQUERADE I want to balance out/in load for eth1..4 and localhost (mainly squid). Nat makes impossible to do it on eth0, so I installed IMQ. I need to get to on imq0 unnnated in/out traffic that I could make priorities for protocols and networks. Do somthing like this: prate=1Mbit

Hi folks, I`ve a problem to use HTB and SFQ. The first script, below, to show a simple configuration, does work fine...!!! But, in the second example, does not work, becouse i put more code to clasify the traffic by protocol, http and ftp in this case. Somebody can tell me the errors? Thx, in advance.- NOTICE: IMQ device is to asociate with ETH1 my external iface. SCRIPT que funciona:

i''m trying to limit upload and download but something is wrong(it is about NAT) i will post here my "script" maybe someone could tell me what is wrong my kernel(2.6.9) is patch with imq(linuximq.net) and my iptables(1.2.11) also #flush tc qdisc del dev eth0 root tc qdisc del dev eth1 root tc qdisc del dev imq0 root tc qdisc del dev imq1 root ifconfig imq0 down

Hi all and tc Gururs i have patched the IMQ and htb to kernel, but when i do egress filtering, iam not able to see any traffic and excusted the following the commands modprobe imq numdevs=1 tc qdisc add dev imq0 handle 1: root htb default 1 tc class add dev imq0 parent 1: classid 1:1 htb rate 100kbit tc qdisc add dev imq0 parent 1:1 handle 10: htb default 1 tc class add dev imq0 parent

Hello, Some time ago I''ve read somewhere that local traffic in IMQ could hung up the whole system but it was corrected long time ago. So I was very surprised yesterday when it occurred not true. While testing IMQ I''ve observed for some time that - if you tag some local traffic with iptables both in pre- and postrouting - kernel is hunging up. It is happening quite quick with

Hello, I wrote a simple traffic shaping script (below) that should have allowed me to shape my internet traffic a bit (ppp0 - adsl 128kbit/64kbit; local interface eth0). The script works only partially - the speed is being limited but too much. Without running this script my download rate is about 10kBytes (with second computer also downloading at about 6kBytes). After running it my download speed

Hey Andreas, how i catch this traffic using L7 filter?, i´ve installed l7 filter now, but i don´t kwnow to use the kind of filter...!!! Can you help me? Thx.- Terraja-based 2007/4/29, lartc-request@mailman.ds9a.nl <lartc-request@mailman.ds9a.nl>: > > Send LARTC mailing list submissions to > lartc@mailman.ds9a.nl > > To subscribe or unsubscribe via the World

hi stef oone more pb while shaping incoming traffic with imq .this one tc qdisc add dev imq0 root handle 1: htb default 20 tc class add dev imq0 parent 1: classid 1:1 htb rate 2mbit burst 15k tc class add dev imq0 parent 1:1 classid 1:10 htb rate 1mbit tc class add dev imq0 parent 1:1 classid 1:20 htb rate 1mbit tc qdisc add dev imq0 parent 1:10 handle 10: pfifo tc qdisc add dev imq0 parent

Hello I have a server with a dsl connection on eth1 and local interface eth0. Because of the NAT i cannot direct traffic to IMQ device in PREROUTING chain but have to use INPUT and FORWARD. So i use rules. iptables -t mangle -A INPUT -i eth1 -j IMQ --todev 0 iptables -t mangle -A FORWARD -i eth1 -j IMQ --todev 0 And now the strange thing: FORWARD traffic gets directed nicely to the IMQ, but

Alejandro, So, i did try the script that you give to me, and the problems its continues.- Maybe the problem was in the IPTABLES rules, i attach the complete script below: ##################### ifconfig imq0 up tc qdisc add dev imq0 handle 1: root htb default 30 tc class add dev imq0 parent 1: classid 1:1 htb rate 500kbit ceil 2000kbit tc class add dev imq0 parent 1:1 classid 1:10 htb rate

Hi, i am running imq + htb on my router , the situation is like this eth0 = uplink to my provider eth1 = 1st customer eth2 = 2nd customer eth3 = 3th customer eth0 has limit 512 and i want to share this between eth1 eth2 and eth3 , but not working , this is the script i used, \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ #!/bin/sh

I have this: class htb 1:29 parent 1:1 prio 0 rate 3000bit ceil 100000bit burst 1599b cburst 1611b Sent 33233 bytes 772 pkts (dropped 0, overlimits 0) lended: 415 borrowed: 357 giants: 0 tokens: -3756376 ctokens: 128779 or this: class htb 1:21 parent 1:1 prio 0 rate 3000bit ceil 100000bit burst 1599b cburst 1611b Sent 57554 bytes 618 pkts (dropped 0, overlimits 0) lended: 193 borrowed: 425

Hi ! I have a single host which is connected via an 512kbit ADSL link to the n= et. I quite often use some realaudio application that uses some bandwidth = and I want to avoid other traffic to scale that bandwidth down. So I used = some classes (with htb) on imq0 device and applied some filters and it see= ms to work in most cases. However, there are some sites with which downloa= d is

Hello, I have HTB on IMQ device. My rate does not work as I configured. I configured 1920kbit/s and I can download only about 290kbit/s (while it should be the whole bandwidth). My script: /sbin/modprobe imq numdevs=1 /usr/local/sbin/tc qdisc del dev imq0 root 2> /dev/null > /dev/null /usr/local/sbin/tc qdisc del dev imq0 ingress 2> /dev/null > /dev/null /sbin/ifconfig imq0 down

Hello, I have a serious problem with HTB which I wasn''t able to solve myself. I run a masquerading router with ppp0 as interface to the Internet. Three clients need to share a downstream of 1 MBit, which I want to divide with tc. When I see a packet being forwarded to one of these clients, I give it the appropriate unique mark: iptables -t mangle -A FORWARD -d 192.168.34.141 -j MARK

Hello, I''m trying to get my shaper to work, but have only a partial success. Can someone help me with that. My setup unfortunately is not so trivial, but I think some people could have similar one... 1. There is a router connected to the internet line via interface eth0 2. There are users connected to the router via two interfaces : eth1 and wlan0 3. All users are assigned private IP