similar to: TCNG Port Range

Hi, I try to shape my incoming traffic. I have 2MBit/s DSL bandwith and the following ruleset (on the internal interface): $INT="eth1"; $INT_NET=192.168.1.0; $MAX_IN=2Mbps; dev $INT { egress { class (<$int>) if ip_src:24 == $INT_NET; class (<$ssh>) if tcp_sport == PORT_SSH; class (<$smtp>) if tcp_sport == PORT_SMTP; class (<$http>) if

Thank you for your help. It generates this script : tc qdisc add dev eth0 handle 1:0 root htb default 2 tc class add dev eth0 parent 1:0 classid 1:1 htb rate 75000bps ceil \ 75000bps tc class add dev eth0 parent 1:0 classid 1:2 htb rate 125000bps tc filter add dev eth0 parent 1:0 protocol all prio 1 u32 match u32 \ 0xa000001 0xffffffff at 12 classid 1:1 But I thought it was necessary to

Hi all, Can someone please help with a tcng setup? I have played with tc and tcng in the past, and now would like to get some serious rules in place. However, I have a difficulty in setting them up. My setup is as follows: One machine working as a firewall: eth0 is the interface connected to a 512K DSL line eth1 is connected to a LAN eth2 is connected to another LAN, a bit like a DMZ eth1 and

Hi I''m completely stuck with the tcng language - I assume there must be some way to arrange queues hierachically like eth1 | TBF | PRIO / \ class class but my attempt (below) produces a "inferno.tc:8: qdisc "tbf" has no classes near "prio"" when run through tcc. dev eth1 { egress { tbf (rate 128kbps, burst 64kb,

Newbie here... tcng version 10b I''m just learning about htb and using tcng. I am trying to make the example in Martin A. Brown''s Traffic Control with tcng and HTB HOWTO v0.5 example 2 /* * Simply commented example of a tcng traffic control file. * * Martin A. Brown <mabrown@securepipe.com> * * Example: Using class selection path. * * (If you are reading the

I can''t seem to match packets less than 512 bytes: class( <$bulk> ) if tcp_dport == 81 && !( ip_len & 0xfe00 ) ; or if tcp_dport == 81 && ip_len < 512 Both rules match any packet I send to port 81, even when the total IP length is much greater than 512 bytes: class htb 2:4 parent 2:1 leaf 5: prio 1 rate 8000bps ceil 24000bps burst 6Kb cburst 1839b Sent

My previous message (http://mailman.ds9a.nl/pipermail/lartc/2004q2/012285.html) didn''t generate any replies, so I thought I''d try posting what I''ve done trying to solve my own problem, in hopes that someone will take pity and show me if/where I''m going wrong. Just to recap, I''m trying to accomplish this on my server, which streams RealAudio files

Hello all, I am trying to set up a simple htb based system, where packets with source ip 10.0.0.1 should have their own class. I plan to use tcng to set it up easier. Is there something wrong in my tcng file ? ~/tcng$ cat htb /* */ #include "fields.tc" #include "ports.tc" dev eth0 { htb ( ) { class ( rate 600kbps, ceil 600kbps ) {

Hey all, i have a class. class ( <$call1> ) if ip_dst == 10.100.1.6 && tcp_dport == 22 if ip_src == 10.100.1.4 && tcp_sport == 22 ; Now when i apply this traffic TO 6 on port 22 is indeed limited to the speed i specify BUT it doesn''t seem to take the src into account at all. If i change the src to anything, even an address that

> Message: 8 > Date: Fri, 14 Mar 2003 21:49:49 +0200 > From: raptor <raptor@tvskat.net> > To: lartc@mailman.ds9a.nl > Subject: [LARTC] [tcng] X:Y to tcng corespondence ! > > Is there a easy way that I to get class-id<----->tcng-class-path conversation.... and vs. versa.. > > --__--__-- There are couple files can be created by tcc: # cat a.tc dev

Hello all, This is just a self-aggrandizing note to inform you all that my rather brief introduction to traffic control using tcng and HTB is available now on TLDP. http://tldp.org/HOWTO/Traffic-Control-tcng-HTB-HOWTO/ I welcome any criticism. -Martin -- Martin A. Brown --- SecurePipe, Inc. --- mabrown@securepipe.com _______________________________________________ LARTC mailing list /

Hi all, The following ingress statement: .... $host2 = SLB(cbs 1024kb, cir 2048kbps); class(<>) if ip_dst == 81.175.84.2 && SLB_else_drop($host2); .... is compiled by TCNG into the folling tc command: ... tc filter add dev eth0 parent ffff:0 protocol all prio 1 u32 match u32 0x51af5402 0xffffffff at 16 classid ffff:0 police index 505 rate 256000bps burst 131072 mpu 0 action

Hi all, I want to apply traffic control using TCNG 1.30 on a NAT router. Can I use the IP addresses on my LAN to shape the traffic on the outgoing interface, with other words, does the address translation take place before or after traffic control? (Or does it depend and if so, on what?) Groeten, Joost Kraaijeveld Askesis B.V. Molukkenstraat 14 6524NB Nijmegen tel: 024-3888063 / 06-51855277

Hello. I have been trying to duplicate these u32 matching rules using TCNG, but without much success: tc filter add dev eth0 protocol ip parent 1:0 prio 1 u32\ match ip protocol 6 0xff \ match u8 0x05 0x0f at 0 \ match u16 0x0000 0xffc0 at 2 \ match u8 0x10 0xff at 33 \ flowid 1:10 Wondershaper 1.1a implements this and if I run it things seem to be shaped as expected. But this TCNG

hi all, i''m having problems building a module from my tcng configuration file. could someone verify the syntax for building a kernel module? i did it as shown below ... module gets built but i cannot load it. thanks charles ps -- sorry, don''t know c++ :-) [root]# cat /etc/tcng.test #define LAN "eth0" #define LAN_INGRESS 750000 #define LAN_EGRESS 750000 dev

Hi folks, first of all, sorry for my bad English ^^ and for the fact that I am a Linux N00b. I have a little Problem installing TCng on my Debian System. At the make install command the following error occured: tar: lib/tcng/include/klib/kernel/include: Cannot stat: no such file or directory tar: Error exit delayed from previous errors Can somebody help me ? greets Marcus -- GMX im TV

I am working on traffic shaping using the nextenso proxy platform(a product of alcatel)on linux platform, I wish to do dynamic traffic shaping means on a fly, is that possible with TCNG?? With Warm Regards, Aruna Baghel "Gratitude can transform common days into thanksgivings, turn routine jobs into joy, and change ordinary opportunities into blessings."

I''ve used tc in the past for shaping, upon learning of tcng, I redid my config, and load it using tcc. I thought this was great, as the new script is much easier to maintain, and is so much simpler. The new script was working for about a week, then it stopped working. I now get this error: can''t dump subexpression (if_u32.c, unsupported offset sequence - please try to reorder

Hey people, I have the following tcng configuration: #include "fields.tc" #include "ports.tc" dev "eth0" { egress { // Voice traffic class (<$voice>) if udp_dport >= 20000 && udp_dport <= 23000; // SSH connections class (<$interactive>) if tcp_dport == PORT_SSH; //

hi, i was looking tcc --help, there seems to be no way to tell tcc to generate output only for specified device i.e. tcc -device eth0 m''I mistaken ? thanx raptor _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/